D-Link DSL 2750U Wireless Router - Combine WLAN With LAN
Oct 28, 2012
I have D-link DSL 2750U wireless router. My PC and notebook are connected to router by Wi-Fi. They can share files or ping each other. I have a network storage unit plugged into router by an ethernet cable. Any of the computers cannot reach that storage unit or ping it. I guess my router isolates LAN network from WLAN network. Is there a way to combine them and get the router treat all devices connected to router in a single network?
View 1 Replies
ADVERTISEMENT
Apr 23, 2012
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
View 2 Replies
View Related
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies
View Related
Apr 22, 2013
I started using a D-link 2750U wireless modem-router about 2 months ago, and configured it using the given disk for my ISP (MTNL Delhi). Since then, it has never retained a connection for more than 10 days, give or take i.e starts showing a red earth light instead of a green one. I usually reset it to factory settings and reconfigure it using the same disc over and over again, but now it has started dropping connection more frequently.Recently, it developed a new disease. Connection is very unstable now. Through line, it keeps disconnecting every 4-5 minutes. re-connects and dies again itself and does not work through wi-fi at allMy hardware quality healthy as I ran a wired connection for over 3 years without any trouble before this one.
View 1 Replies
View Related
Aug 6, 2012
configure my D-link wifi Modem DSL-2750U for Reliance Broadband.I dont understand codes but a simple explanation and step by step
View 3 Replies
View Related
Feb 15, 2013
I have a new internet router linksys EA2700 Firmware Version: 1.0.14, the wireless signal doesn't cover the whole house so I like to extend the wireless signal using my old router Dlink DSL-2750U as Access point, I configured the two router as following but yet didn't work.
Linksys
DHCP: enabled,
IP lease range 192.168.1.100 to 150
Wireless SSID, Security Mode, Passphrase, Channel Width and Channel number same as Dlink
Dlink:
DHCP: disabled
AP Mode: Access point
Bridge Restrict:Enabled
Remote Bridges MAC Address: is the linksys MAC.
And I removed the Layer2Interface and WAN old configuration.
View 3 Replies
View Related
Aug 4, 2011
I am a day trader using Microsoft 7.I need to combine cable (comcast) and a wireless connection (AT&T) as backup into one access point.
View 1 Replies
View Related
Sep 17, 2012
My Dlink DSL 2750u 3g internet wont stay active if my computer is off. My pc ain't quite a power saver.
View 1 Replies
View Related
Jun 10, 2013
I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
View 4 Replies
View Related
Dec 19, 2012
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I recently purchased an TL-WDR3600. Setup was easy. Both wlan channels work perfectly. All clients can connect to the internet and access my lan connected NAS. I have some wlan devices which needs to be connected sometimes by http: port 80 and also by telnet or ssh. I can connect from a wlan device to a lan device. But NOT from a wlan to wlan or a lan to wlan. I allready diabled WMM and tried some other wlan settings, like disable one channel, changing the channel width etc.
My setup is : ADSL device -->(192.168.1.X dhcp) WAN TL-WDR3600 --> to LAN&WLAN (192.168.0.X dhcp and some LAN connected with static 0.200, 0.210)
View 6 Replies
View Related
Jun 13, 2011
I want a solution which should be 2 WAN convert in to 1 WAN.
View 1 Replies
View Related
Aug 15, 2012
I am using 2 internet data card and would like to merge them to have high speed. I am using XP and Window 7
View 1 Replies
View Related
Mar 2, 2012
What I want to do is combine a sad 1.5M DSL connection and a long range WiFi signal into a single connection for a rural area home.I am looking for any effective solution (including boosting WiFi output signal beyond FFC suggested values). The WiFi long range antenna (DISH + gutted LNB) receives a full bar 40+ Mbps signal from 11 miles away. DSL is standard 1.5M over DSL Modem.
View 2 Replies
View Related
Jan 31, 2011
I have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt.As u know the connections work separately by default!! (I use Windows 7 64bit)Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 2 Replies
View Related
Jul 28, 2011
I have a small call center and we are struggling with adequate dsl bandwidth for our voip. The providers cannot give us more upload bandwidth. Any way to combine the bandwidth of two or more lines so that the server/switch sees increased bandwidth for upload?
View 1 Replies
View Related
May 26, 2012
I'm going to combine 2 512 kbps ADSL line in my PC. i know that it would be much better to get a 1 MB ADSL connection...but the problem is where i live now there is not better speed than this! Well i have a PC with 2 LANs - 2 phone lines - 2 ADSL modems - as far as i learned from Google , by no means it is possible to combine them to have 1 MB data rate but it is possible for example IDM would works with one 512 and another program with another 512..!! And load balancing is the only solution for this which it needs a special routers ! it is somehow difficult for me to provide one ..!! so my question is :
1- Is there any other solution for combining this 2 lines?! I heard something about teaming.
2- Is it possible to use load balancing by software?
3- How about the efficiency and ping time?
View 1 Replies
View Related
Jan 31, 2011
I have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt. As u know the connections work separately by default!! (I use Windows 7 64bit) Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 3 Replies
View Related
May 6, 2012
My apartment complex limits each connection to 200KBps but each connection has the same IP so I thought there has to be an easy way to combine the connections. Is there a way to connect the wired network i'm connected to with the wireless one?
View 3 Replies
View Related
Mar 11, 2011
Wired computers can't see wireless and wireless can't see wired pcs.
View 8 Replies
View Related
Apr 27, 2011
setting up a simple internet plan for a place, but a LAN center needs crazy fast internet, faster than most large enterprise class offices that take up an entire floor or two. Otherwise there is too much lag in games like first person shooters. We are expecting to have 60 computers, plus people bringing their own gaming rigs from home and laptops as well, xbox, ps3 and other consoles, all accessing the internet at the same time to varying degrees, with no room for lag. There is a LAN center in california that has 200 or more computers and they pay for 9 t3 lines, which is thousands and thousands of dollars per month. Plus the initial equipment to set that up from what I can find on cdw is many thousands of dollars also. Something like 10,000 for a router with 4 expansion bays, and 4000-6000 dollars for a t3 expansion card, bringing the total to around 22-28,000 for equipment to do just 4 t3's. Plus the monthly cost. Since we don't need all of the traffic to be secured like a high end business class line like a t3, I was considering what it would be like, and how one would set up, having multiple cable internet lines coming in. They make cable wic cards for cisco routers. 4, 50meg cable lines would give us 200 down and 40 up but I don't know how to make that work without having multiple public ip's. I was thinking that if I did have multiple public ip's on the network I could just divide the computers up so that they are in groups, using all of the public ip addresses for gateways, so that the load is split pretty evenly, but still, there should be a more seamless way to do this, I just don't know what it is. At the rate for business cable internet, 4 lines would probably only cost around 700 dollars a month, which is much better than probably 5 grand a month for several t3 lines.
View 3 Replies
View Related
Dec 2, 2011
I just installed a new RV016, and have it up and running currently using just one WAN (cable) on the Internet2 port. Just FYI I do plan to have a second WAN on Internet1 (DSL) once I get this next step working and want that to be the dafault provider, hence the use of Internet2 for this first connection.I already have a WRVS4400N installed that has a whole network on it that will be independant to the new the network and am trying to connect the WRVS4400N to my RV016. It is currently plugged into port 8 of the RV016 and the port is currently set to VLAN2.I know just enough to be a danger to myself here. :-) The RV016 is using the default IP of 192.168.1.1 while the WRVS4400N uses 192.168.10.1.I do know that "Typically, a Cisco RV0xx Series router is used as an access router, with a single LAN subnet. By default, the firewall is pre-configured to deny LAN access if the source IP address is on a different subnet than the router’s LAN IP address. However, you can enable multiple subnets to allow this router to work as an edge device that provides Internet connectivity to different subnets in your LAN."Hence I have added added the 192.168.10.1 subnet with mask 255.255.255.0 (to the RV016) and have tried switching the WRVS4400N from Gateway mode to Router mode. The RV016 can see it but nothing on the WRVS4400N network has any internet access, while computers on RV016 do. I assume this is because of the firewall blocking the traffic.
View 3 Replies
View Related
Feb 3, 2012
I'm trying to combine dynamic and static NAT on a SR520. My dynamic NAT is specified with:ip nat inside source list 1 interface Dialer0 overload access-list 1 permit 192.168.0.0 0.0.7.255 In addition to this I want to perform static NAT for a couple of selected internal hosts. I can do this:ip nat inside source static 192.168.1.5 10.85.10.2 which works fine but means that the source address 192.168.1.5 is translated to 10.85.10.2 for all destination IPs. What I want is for the above static translation only to occur for a particular destination subnet.To accomplish this I have tried:
ip nat inside source static 192.168.1.5 10.85.10.2 route-map toOtherSite
route-map toOtherSite permit 10
match ip address 150
access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
But this does not appear to work. Instead it seems to render the host 192.168.1.5 unable to progress through the NAT, whether the destination subnet is 192.168.10.0/24 or not, and I can't work out what I'm doing wrong.
View 2 Replies
View Related
Oct 1, 2012
I have cisco 1841 router and two types of ISP line (Different provider):
1. Lease line = 2 mbps ( it is terminated over cisco 1841 router); For internet-access purpose
2. DSL = 1 mbps; For internet-access purpose
Our cisco 1841 router have only two fastethernet port, first for WAN Port where 2 mbps lease line terminated , second for LAN which is connected to Cisco switch and 1 mbps adsl line running seperatly which is not part of cisco 1841 router. i am planning to buy HWIC card for extra wan port on existing router where i will terminate 1 mbps adsl line or may be other provider lease line.I want to merge or aggregate both WAN link, My concern is to merge both line (2+1) and get single one (Just like as Etherchannel thing) , get 3mbps for LAN for internet access.
View 23 Replies
View Related
Feb 21, 2011
I use the dlink router with 12mbits internet connection. Connection with LAN wire, i get the whole 12 mbits. Via Wlan, even while standing next to the router, i only get 5-6 mbits.
I read this can be cos i send in mixed mode b/g. Is that true? How can I set to g only? I only can select "n only", "b/g mixed" and "b/g/n mixed". But I think all my devices use g.
View 3 Replies
View Related
Mar 4, 2013
I am having issues trying to combine two modules into one VDC. The modules are as mentioned below: When I try to combine module 1 & 10 as shown above, the nexus 7000 switch displays 'Not compatible'. I've read the online guide and it mentions that the F2 and M1 module cannot be combine into the same VDC. Problem is, my customer has already purchased the module, how do i solve this problem? If I separate the VDC, how does module 1 talk to module 10 if user wants to send traffic to Internet or Server Farm?
View 3 Replies
View Related
Dec 31, 2011
my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.
View 1 Replies
View Related
Oct 5, 2011
As the title might suggest, my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.
It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.So yeah, it's not pretty but I have to work with what's available. I'm actually surprised it even works this well. how to optimize the whole thing or how to fix the partial lack of connectivity?
View 5 Replies
View Related
Jan 8, 2011
When I was using my Linksys router, I had no difficulties setting up Windows File Sharing on my computers but since I upgraded to the DIR-655, file sharing have hardly worked. Sometimes I could get one of the computers access files on another, but not the other away around. Most of the time, none of the computers have access to the files on any of the other computers. Two of the computers run Windows XP and another one runs Windows Vista. All computers are on the same workgroup and able to connect to the internet through the router. When calling D-Link tech support, I am told that they dont support file sharing and that I had to contact each computer's manufacture's tech support on the instructions on setting up the file sharing (each computer is from a different manufacture). One of the tech supports did drop the slight hint that I needed to recreate the home network, but when I tried to do that, all I could find is the settings to connect to the router (which I had set up when I installed the new router) and to enable file sharing (which is already done) and to assign the workgroup, which they were all are already assigned to the same group.
View 8 Replies
View Related
Mar 29, 2013
I have a DCP 3925 with 2 telephone and 4 internet ports.So, how can I combine DPC 3925 + E3000 to have more internet ports? and wich one is the best wifi than I can use ??Main router is the DPC 3925, where the internet is connected.
View 9 Replies
View Related
Dec 5, 2012
When the front-panel WLAN LED light is solid, it indicates that the wireless segment is ready; it blinks during actual wireless data transmission. This is how it behaved for me until I added some MAC addresses to Advanced > Network Filter. Now it stays solid even during wireless data transmission. Even after a reboot. If not, how do I get the blinking back?
View 14 Replies
View Related
May 18, 2012
Yesterday the WLAN light stopped lighting up on my wireless router. The DSL light comes on (green), however, the WLAN light doesn't light up and the 'inetrnet' light stays on red. My laptop is saying cannot detect network, but is detecting other wireless networks in area (so not laptop prob). Did all the unplugging, turning everything off and even pressing the reset button on the back of the router but its still not working. Tried plugging in a USB cable directly from router to laptop and 'internet' light flashed green for 1 second then went back to red and still not working.
View 1 Replies
View Related
Feb 13, 2012
I accidentally pressed the front panel button labeled "Cisco Systems" on my WRT54GL wireless router. The button turned to a flashing white which I understand means that it entered SecureEasySetup mode. I then power cycled the router and the front panel button turned back to solid orange. However, now the "WLAN" lamp flashes a lot more often than before even when there are no wireless clients connected. It doesn't seem to be affecting connectivity or performance of my Ethernet connected devices or wireless connected devices. I re-entered my SSID and security key. That didn't curtail the increased flashing of the WLAN lamp. I also tried pressing the front panel button for 5 seconds. This only cleared my wireless settings.
View 2 Replies
View Related
Jul 22, 2012
The E1200 is connected to a router (BEFSR41) that is acting as DHCP server. So I have disabled the DHCP Server option on the E1200. Once configured, the wireless connection is working by unexpectedly only as guest user (I tried via PC XP, PC Win 7 and IPad) on the guest network. The problem is that once configured, the E1200 is no more reachable unless I reset it and I reconfigure it. If I try to access the IP 192.168.1.1, I get the setup page of the router (BEFSR41) and not the E1200. From another computer the IP Scan discover the E1200 as 192.168.1.103, but I am not able to reach it at that address.
View 5 Replies
View Related
