D-Link DIR-600 :: Access Point Via Laptop Connected To WLAN?
Dec 31, 2011
my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.
As the title might suggest, my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.
It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.So yeah, it's not pretty but I have to work with what's available. I'm actually surprised it even works this well. how to optimize the whole thing or how to fix the partial lack of connectivity?
I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
My wlan says connected but cannot access the internet. LAN does not work either. I suspect there is a virus somewhere but I cannot update any antivirus software to remove the virus.
I have a bsnl wireless modem but I can't access internet through my phone.Though i have enabled the wlan and set up all the configurations I can't connect using the wireless.
I use the WAP610N as an Accesspoint for only an small Mobilephone to WLAN Printer Network.My big Problem is that i have therefore no DHCP Server in this special small WLAN Network.And now i need an own DHCP Server from the Accesspoint side because otherwise i must use static IP Adresses in all Mobilephones to connect with the WLAN Network .In the WAP610 unfortunately there is only the choose between static IP Adress and IP Adress FROM an existing DHCP server .
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm] %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
I got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
I connect a wireless access point to our network and within 10-15 minutes any wired LAN users internet connection goes down, yet the wireless internet works fine.
Here is how our small business network is setup:
1. We have a Server 2000 that serves as our companies domain controller and DHCP (I know, I know..dated). We also have another server on our network, which is a Server 2003, which is primarily a backup domain to our Server 2000 and hosts Quickbooks that our employees use and a small intranet website via ISS. We are connected to a router from our ISP with a gateway IP of 192.168.1.2. Our ip address structure is 192.168.1.xxx and subnet is 255.255.255.0.
2. I have configured the AP to be just that, an access point to broadcast wirelessly and made sure that DHCP is turned off on the router. I set it to a static ip of 192.168.1.215 and subnet of 255.255.255.0 and our default gateway of 192.168.1.2. Once I connect it, everything works fine for about 20-30 minutes, then our LAN internet goes down. The Wireless G access point that I am using is a TP-Link Model TL-WA501G.
My question is, how does the WAP know that our server is the DHCP? And are the wired LAN people getting disconnected because of a DHCP fighting issue between the WAP and our server 2000? I'm not a network engineer but know enough, but this problem is really baffling me.
Any issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).
I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.
Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?
dell 170L (old but very stable) winxp/pro linksys wusb54gs adaptor
installed the software and i get the "connected to the access point (very strong signal) but the internet cannot be found"this was working for quite some time and i shut the system down for quite a while before needing to set it up again.
I have a big house so I have a e4200 on one end of the house upstairs and the WAP610n on the other end downstairs linked via CA6. I am having no issues with Laptops etc..just with Apple devices. I spent a lot of time with chat support (waste of time). WAP was flashed with latest firmware via hard wire no devices connected to wireless, has same ssid and security settings as router running on 2.4 ghz wpa2 personal AES. I am using 2.4 due to iphone4 does not support 5ghz and wap does not support dual band (another bummer). I am using AES instead of TKIP/AES mixed mode due to apple devices will not acquire dhcp with this setting and if they do they lose it right away. I have tried everything imaginable with the settings even changed beacon to 75, 50 RTS to 2304 etc...the current setting are the only ones that seem to work the best however when i run speedtest.net LA server or SD server the performance is horrible. On windows laptop i can achieve 27mbps down 2.5mbpsup, my apple devices use to achieve very close numbers to that on a simple configuration with two Dlink DGL-4300's one as router one as AP (G mode). So two major issues i have noticed is WAP610N has issues passing DHCP to apple devices and has extremely poor performance. So my question is will there be a firmware to correct this issue or a new hardware version that i can exchange this for if I RMA it or would it be best to call it a day and just get a E3200 and use it as a real simultaneous dual band AP???
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
A 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.
I want share my adsl internet connection to my galaxy tab and use labtop wirless as a access point. in toturials there is settings in wirless newworks tab in wirless propertice,but I cant found this tab. I installed lastest Wirless driver update and start WLAN autoconfige service. also I cant found microsoft virtual wifi in network connetions.
I recently got an access point to extend the wireless range in my house. It is a Netgear WN802T. The long and short of it is, it works fine, i configured it succesfully, it reaches the main router and gets an IP address from it. My laptop connects to it fine without fuss. However, my phone (HTC Desire HD) and tablet (Motorola Xoom) are unable to connect.They can 'see' the access point, but when i connect and put in the passcode, it get's stuck on 'scanning' or 'disconnected'. I've tried turning certain settings on and off, i've tried taking it out of G/N mode and taking it down to B/G mode.
I've tried multiple types of security (WPA-PSK, WPA-PSK 2, TKIP, AES...), the odd thing is, the type of security my main router uses (which the phones connect to without a hitch) does not work. I have tried different channels. My main router's channel is 1, which works perfectly fine. To make sure there is little interference, i set the AP channel to 4. I've also tried auto, no avail.
The laptop doesn't seem to care what i change the settings to, it connects fine and gets the internet perfectly. But my phone and tablet just don't want to play ball. I don't think the router is broken or anything, it works fine, but i think there's some incompatibility issue here that i'm not seeing.
I installed the DIR-655 on my home network a couple weeks ago to replace an older model D-Link that failed.
I'm having trouble with my laptop maintaining a connection to the network ever since.
Details: Firmware Version : 2.00NA , Wed, 12, May, 2010 Hardware Version: B1 Desktop WinXP hardwired to router Blu-Ray player hardwired to router Dish Network received hardwired to router Laptop Win7 wifi Android phone wifi CenturyLink DSL
It seems that the wifi stays up until I try to access the internet via the laptop. After a few seconds, the laptop will disconnect, and many times the router seems to reset itself, though not always. This does not happen when using a hard-wired connection. Using the wifi-enabled Android phone doesn't seem to affect the network.
Sometimes the wifi comes back up pretty quickly, but other times it does not. Earlier today, the internet globe light on the router turned from blue to amber. I had to reset the CenturyLink DSL modem for it to work again.
When the network goes does, I get a message on my desktop that a network cable is unplugged, and the network disappears from my available wifi networks that I can see with the laptop. Sometimes I get the "limited connectivity" message.
I have tried changing the 802.11 mode around, and I've changed from Auto Channel Scan to Channel 1. Neither of those have fixed the problem.
Everything worked fine until I went to move my desk to a different area and had to unplug everything. Upon plugging everything back up - my desktop internet works fine, but the laptop says "Connected but no internet access". I've tried working on it for 2 hours unplugging and replugging cords back up and I can't get any internet access on my laptop. I am using a cable modem. Currently I have the blue ethernet cord running from the modem, directly into my computer. I also have a grey cord that apparently was plugged into the router somehow but I don't remember how exactly I had this one plugged up. The cable modem only has one jack, for "ethernet". The router is a Linksys WRT54G and has 4 numbered (1-4) jacks in the back and then one jack for "internet". The laptop is running Windows 7, and the desktop (which the internet runs fine on right now) is running Vista.
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1 Processor Count: 1 RAM: 479 Mb Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB; Motherboard: , KM266-8235 Antivirus: None
I just bought a new laptop and have had issues with it from day one regarding the internet. It connects me to the internet, but then after a few minutes on the task bar where it tells you what you are currently connected to a yellow (!) shows up. It tells me that I am connected to my network, but it says that I do not have any or sometimes even limited internet access. I have other computers in the house (3 laptops, sometimes 4, and 2 desktops) that do not have any issues connecting or staying connected to the internet. The laptop with the issue has Norton installed on it and it is with Windows 7. My ISP is AT&T, DSL. My router is a LinkSys router.
My os is vista I have belkin Wireless router Iam trying to connect my laptop to wireless.it wont have any problem outside of home but at home i click on connect to a network and click on my wireless network and it says sucesfully connected but it is not connected to internet network and sharing center shows unidentified network?
I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
I setup an accespoint on my laptop. Now I want to connect my Phone (android) to this network but, he is asking for an Ip-address I tried the following;
I have a DIR-655 Rev B1, FW 2.01 (I will probably upgrade the FW tonight to the latest.)
I have at least 20 items that connect wirelessly to this router (2 PCs, 2 Laptops, 2 Tivo Box, 3 Game Consoles, 3 Cell Phones, 2 Tablets, 2 TVs, Printer, AP Gateway, and some other projects) It's been a solid connection to everything for the past couple of years.
I bought a new Dell Inspiron 15r SE laptop (uses the Intel Centrion Wireless-N 2230 Wifi Solution.) After anywhere from 2 - 10 mins of browsing/watching a video/downloading files the access out to the internet simply stops.
At this point I'm still connected wirelessly to the router, and if I go to the router address I still have access and can login and see the router settings. I check and there's plenty of time left on the lease (days.) Still not getting internet access. Eventually my Laptop will disconnect and reconnect (or I do it manually.) I've performed hard resets of the router, I've had my laptop Forget the network and then reconnect, etc. Nothing has resolved it.
I thought it may be my laptop, but I've taken it to Starbuck, Work, Neighbors WiFi, etc and I don't have any problems staying connected on their networks.
I've had Dell on the line, we connected hardwired, and there solution was to force forget and reconnect to the router, which worked for the 10min he was on the line with me, but then failed soon after, and back in the same connectivity hell
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
