I connect a wireless access point to our network and within 10-15 minutes any wired LAN users internet connection goes down, yet the wireless internet works fine.
Here is how our small business network is setup:
1. We have a Server 2000 that serves as our companies domain controller and DHCP (I know, I know..dated). We also have another server on our network, which is a Server 2003, which is primarily a backup domain to our Server 2000 and hosts Quickbooks that our employees use and a small intranet website via ISS. We are connected to a router from our ISP with a gateway IP of 192.168.1.2. Our ip address structure is 192.168.1.xxx and subnet is 255.255.255.0.
2. I have configured the AP to be just that, an access point to broadcast wirelessly and made sure that DHCP is turned off on the router. I set it to a static ip of 192.168.1.215 and subnet of 255.255.255.0 and our default gateway of 192.168.1.2. Once I connect it, everything works fine for about 20-30 minutes, then our LAN internet goes down. The Wireless G access point that I am using is a TP-Link Model TL-WA501G.
My question is, how does the WAP know that our server is the DHCP? And are the wired LAN people getting disconnected because of a DHCP fighting issue between the WAP and our server 2000? I'm not a network engineer but know enough, but this problem is really baffling me.
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
Any issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).
I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.
Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?
my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.
As the title might suggest, my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.
It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.So yeah, it's not pretty but I have to work with what's available. I'm actually surprised it even works this well. how to optimize the whole thing or how to fix the partial lack of connectivity?
dell 170L (old but very stable) winxp/pro linksys wusb54gs adaptor
installed the software and i get the "connected to the access point (very strong signal) but the internet cannot be found"this was working for quite some time and i shut the system down for quite a while before needing to set it up again.
I have a big house so I have a e4200 on one end of the house upstairs and the WAP610n on the other end downstairs linked via CA6. I am having no issues with Laptops etc..just with Apple devices. I spent a lot of time with chat support (waste of time). WAP was flashed with latest firmware via hard wire no devices connected to wireless, has same ssid and security settings as router running on 2.4 ghz wpa2 personal AES. I am using 2.4 due to iphone4 does not support 5ghz and wap does not support dual band (another bummer). I am using AES instead of TKIP/AES mixed mode due to apple devices will not acquire dhcp with this setting and if they do they lose it right away. I have tried everything imaginable with the settings even changed beacon to 75, 50 RTS to 2304 etc...the current setting are the only ones that seem to work the best however when i run speedtest.net LA server or SD server the performance is horrible. On windows laptop i can achieve 27mbps down 2.5mbpsup, my apple devices use to achieve very close numbers to that on a simple configuration with two Dlink DGL-4300's one as router one as AP (G mode). So two major issues i have noticed is WAP610N has issues passing DHCP to apple devices and has extremely poor performance. So my question is will there be a firmware to correct this issue or a new hardware version that i can exchange this for if I RMA it or would it be best to call it a day and just get a E3200 and use it as a real simultaneous dual band AP???
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
A 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.
I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
So, for some reason my internet connection started disconnecting about every 1-5 minutes. It worked fine this morning, however, when I turned my PC on a few hours ago it became very unstable. After it happens I have to reconnect to internet (it doesn't work all the time, I usually have to do it two times for it to work), and then again after a few minutes the connection dies. Tried restarting my computer, tried restarting the modem, tried the troubleshooting network thing (it keeps saying "Local Area Connection doesn't have a valid IP configuration", but gives no solution). Also, I tried connecting on my cellphone and on a laptop and both of those work. However, those connect through WiFi, while my PC is connected through an ethernet cable[code]
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
