D-Link DIR-655 :: Router Is Not Recognizing Laptop As Directly Connected Device
Oct 27, 2011
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
View 1 Replies
ADVERTISEMENT
Nov 11, 2012
I've been trying to find a response or a fix to this issue for a few weeks now.My DIR-655 RevB router is currently at firmware 2.07NA, and has speeds of around 30Mbps down and 10Mbps up when connected directly through wired connections.However over wifi, I am only getting around about 5 Mbps down and 2 Mbps up. I've tried the 'usual' fixes suggested on here, change broadcast signal to manual, not auto, shutting of QoS shaping, all of that. However nothing seems to be improving the speed.
View 8 Replies
View Related
Jun 9, 2011
I have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again. I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do. When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
View 12 Replies
View Related
Aug 9, 2012
I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.
View 1 Replies
View Related
May 5, 2012
my laptop stopped recognizing my wireless router out of nowhere. One minute it was connected to the internet, the next it was on and off, I reset it and restarted and it wasn't recognized. Currently only working if Ihave an ethernet cable directly connected from modem to laptop or modem to router/router to laptop.
Specs:
Windows 7
Time Warner Cable modem
Edimax wireless router
View 13 Replies
View Related
Apr 14, 2013
I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
View 5 Replies
View Related
Mar 27, 2011
Should the DIR-655 list all devices that are accessing either my WAN or another device on the LAN, assuming there are no other switches on the network, and all traffic is going through the DIR-655?
I was trying to determine the IP, and MAC address of an AT&T Microcell connected to my network. I have no physical access to Microcell. I have been able to find the IP address, in the logs of the DIR-655, but nowhere else. Shouldn't it be listed under SETUP -> NETWORK SETTINGS -> NUMBER OF DYNAMIC DHCP CLIENTS?
View 2 Replies
View Related
Oct 12, 2012
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
View 6 Replies
View Related
Apr 26, 2011
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies
View Related
Jul 18, 2011
I have had my DIR-825 for a year and half. My computer that is wired directly to the router keeps losing the connection to the router - unable to obtain an address. All of my other devices (that are connected via wireless) still hold the connection with no issues. I've checked the cable, unplugged/plugged back into the router, and it shows connection on the network card on the back of the computer.I have used the system interface to ensure the address is a valid one. I have powered up and down the computer multiple times and have also powered down and up both the router and the cable modem.
View 1 Replies
View Related
Jun 21, 2011
I set up a network several years ago. The network was to use a printer between an old desktop with XP and a laptop with Vista. This has worked very well until several weeks ago. I would logon to the network on the laptop through the desktop, type in the password and I was good to go. Suddenly the password does not work. The printer works fine through the desktop. We have had several lightening storms in our area recently.
View 14 Replies
View Related
Jan 24, 2013
Can i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies
View Related
Aug 29, 2011
I know there are a lot of threads out there regarding connection issues, both with wireless & LAN connections, after updating firmware to 1.35. To provide a snapshot of my setup...I have 3 GB switches throughout my home, a couple Ethernet enabled Blu-Ray players, 2 XBOX 360's, multiple satellite receivers with Ethernet, 5 PC's, 3 iphones, etc...you get the picture. I also have 5 older DLink wi-fi cameras. So, with this said my setup has been flawless for some time. However, a week or so ago I upgraded my firmware on my DIR-655 to the latest version...everything still seemed fine at the time. Yesterday I noticed we had no wireless internet so I went and checked. Sure enough...no connectivity on my desktop that's directly linked to the router, etc.
I tried rebooting & then resetting the router...got connectivity, but as soon as I plugged my PC into the switch...no IP address. I played around with settings, wiring configurations, etc...I'm pretty up to speed on this setup so I felt I exhausted every option. I thought my router went bad...gave me an excuse to go get the latest so I brought home a NetGear N750...hooked it up. As soon as I changed the LAN IP address range to condense the #of IP addresses I'm giving out again, the LAN connection to the PC was lost...I could not get it restored. I finally got it working, bypassing the GB switch, but the wireless would lose connection literally after a few seconds.
I ended up taking the NetGear router back and bought the exact same DIR-655, but this time it was HW version B1 instead of A and it was firmware #2.00 or something like that. I hooked it up when I got home...configured the system to exactly the way I had it before and PRESTO!!! My system is working like it was before. I can only think that the firmware upgrade I made on the previous router screwed something up in my system.
View 4 Replies
View Related
Feb 29, 2012
Why isn't it possible to make following configuration:
View 9 Replies
View Related
Jan 16, 2012
if you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies
View Related
Mar 27, 2012
Can an ip address be NAT'ed to an ip address on a PIX 515 which isn't an ip address of a network directly connected to an interface on the PIX?
Specifically, can a host with an ip address of 150.140.102.3/26 which is connected to a network whose PIX firewall interface is 150.140.102.1/26 be NAT'ed to an ip address of 150.90.70.1/24 which is not a ip address of an interface that is directly connected to that same PIX 515?
I've attached a PDF depicting the network topology and describing the above.My first response to this question is that it can't be configured to do this, but need either a confirmation or correction to this.
View 2 Replies
View Related
Aug 12, 2012
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
View 14 Replies
View Related
Jan 15, 2012
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies
View Related
Jan 14, 2013
i'm using WLC AIRCT5508-K9 software version 7.3.101.0, ISE, cisco prime infrastructure 1.2 (1.2.1.012), and using Odyssey access client manager all running well but here the problem, when a user connected to our SSID, the status of connection information especially on access point.. there appear that "Access point : WLC2-ISC-JKT-GCC".that is the WLC not the access point, is there any miss configuration from me..
View 5 Replies
View Related
Mar 28, 2013
I'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).
View 2 Replies
View Related
Nov 3, 2012
We had a problem where a 4500 would not ping directly connected devices dispite being able to telnet to them and also view them in CDP. It was mostly forwarding packets between devices but some hosts could not connect to others.
View 1 Replies
View Related
May 24, 2012
is there a link to directly download the EA4500 firmware?
View 3 Replies
View Related
Jun 21, 2011
I installed the DIR-655 on my home network a couple weeks ago to replace an older model D-Link that failed.
I'm having trouble with my laptop maintaining a connection to the network ever since.
Details:
Firmware Version : 2.00NA , Wed, 12, May, 2010
Hardware Version: B1
Desktop WinXP hardwired to router
Blu-Ray player hardwired to router
Dish Network received hardwired to router
Laptop Win7 wifi
Android phone wifi
CenturyLink DSL
It seems that the wifi stays up until I try to access the internet via the laptop. After a few seconds, the laptop will disconnect, and many times the router seems to reset itself, though not always. This does not happen when using a hard-wired connection. Using the wifi-enabled Android phone doesn't seem to affect the network.
Sometimes the wifi comes back up pretty quickly, but other times it does not. Earlier today, the internet globe light on the router turned from blue to amber. I had to reset the CenturyLink DSL modem for it to work again.
When the network goes does, I get a message on my desktop that a network cable is unplugged, and the network disappears from my available wifi networks that I can see with the laptop. Sometimes I get the "limited connectivity" message.
I have tried changing the 802.11 mode around, and I've changed from Auto Channel Scan to Channel 1. Neither of those have fixed the problem.
View 7 Replies
View Related
Apr 11, 2013
I am trying to test (if possible) the idea of having 2 6509-E switches connected directly to each other while using VRF-lite (Sup 2T). The idea is to have 3-4 separate networks. For example Net-A, Net-B,Net-C, Net-D. There is no PE router*, just these two switches. Also, there sin't any other access layer switches. All users connect directly to the 6509-E's via switch 48 port switch blades.
Net-A and Net-B on separate VRF's, but able to talk to each other. Net-C and Net-D* on separate VRF's without being able to talk to any other. Net-D* will have a PE since it comes from an external network. This is something I would like to test in a lab environment, but I am not familiar with VRF's.
View 1 Replies
View Related
Dec 31, 2011
my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.
View 1 Replies
View Related
Oct 5, 2011
As the title might suggest, my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.
It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.So yeah, it's not pretty but I have to work with what's available. I'm actually surprised it even works this well. how to optimize the whole thing or how to fix the partial lack of connectivity?
View 5 Replies
View Related
Jul 17, 2012
access points are directly connected to 2016 wlc.Event log from the wlc
AP event log download completed.
======================= AP Event log Contents =====================
*Mar 1 00:00:30.157: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:30.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:30.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:30.191: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
[code]....
but still access points are not functional ?
View 17 Replies
View Related
Dec 1, 2011
I have a CAT 3560 connected to a ISR 2911 The 3560 has 2 subnets ( 192.168.1.0 /24 and 10.10.10.0 /24) The 2911 has interface GigabitEthernet0/1 on the 192.168.1.0 /24 and another GigabitEthernet0/0 on a WAN connection 172.16.7.246 I need to NAT both the 192.168.1.0 /24 and the 10.10.10.0 /24 to the single address 172.16.7.246 I have to use route-maps . I have IPSec VPN's and ZBF on the 2911 My problem is the NAT does not work for the 10.10.10.0 /24 network!Why?is my only option to use trunking between the 3560 and 2911 and subinterfaces on the 2911? I want to avoid sub-interfacing.
=============================================================
On the Cat 3560=====================!vlan 40name the 192.168.1.0 /24 subnet!vlan 60name the 10.10.10.0 /24 subnet!interface FastEthernet0/7description Connection to Router Gig0/1switchport access vlan 40!interface FastEthernet0/16description Connection pc host on the 10.10.10.0 /24 subnetswitchport access vlan 60!interface Vlan1no ip address!interface Vlan40ip address 192.168.1.4 255.255.255.0!interface Vlan60ip address 10.10.10.10 255.255.255.0!ip classlessip route 0.0.0.0 0.0.0.0 192.168.1.1
=========================
The host on the 10.10.10.0 /24 network has the 10.10.10.10 address as it's default gateway The host can not access the WAN thru NAT....
View 3 Replies
View Related
Jan 9, 2012
My Data Center has one single core switch where is connected several servers, one port is the link to the router wan and other port is the link to the FW, my boss wants to install 2 nexus in order to replace the single switch. All my network has only one address, for example 192.168.10.0/24 if I connect two nexus 7010 in VPC and Domain, each nexus is going to has 2 modules with 48 port 10/100/1000 rj45 and i wan to connect servers directly to each nexus, with this figure i'm going to have a group of servers connected in two different nexus, Do they can have the same network 192.168.10.0/24 considering that the nexus are in the same vdc and vlan and have only one gateway for both groups? If the answer is positive, which nexus would be the gate way for that address, the primary or secondary? Or i must have a different address for both group of servers, i mean for example 192.168.10.0/24 and 192.168.12.0/24?thus each nexus would be the gateway for that new address?
To have two nexus connected by VPC in a Domain mean that one computer connected to one nexus can share the same address or vlan with other computer connected to the other nexus????
View 2 Replies
View Related
Sep 9, 2012
We have a 3750X VTP Server and the rest of the switches are clients.
Due to cabling issues, we have a switch (Switch F) that we can't connect directly to the 3750X so we have it connected through another switch. Everything is set to VTP client with the correct domain and password but this not-directly-connected switch isn't receiving any VTP VLANs.
Anything I need to do on Switch D so that Switch F can receive the VTP updates?
View 3 Replies
View Related
May 14, 2013
I have a DIR-655 Rev B1, FW 2.01 (I will probably upgrade the FW tonight to the latest.)
I have at least 20 items that connect wirelessly to this router (2 PCs, 2 Laptops, 2 Tivo Box, 3 Game Consoles, 3 Cell Phones, 2 Tablets, 2 TVs, Printer, AP Gateway, and some other projects) It's been a solid connection to everything for the past couple of years.
I bought a new Dell Inspiron 15r SE laptop (uses the Intel Centrion Wireless-N 2230 Wifi Solution.) After anywhere from 2 - 10 mins of browsing/watching a video/downloading files the access out to the internet simply stops.
At this point I'm still connected wirelessly to the router, and if I go to the router address I still have access and can login and see the router settings. I check and there's plenty of time left on the lease (days.) Still not getting internet access. Eventually my Laptop will disconnect and reconnect (or I do it manually.) I've performed hard resets of the router, I've had my laptop Forget the network and then reconnect, etc. Nothing has resolved it.
I thought it may be my laptop, but I've taken it to Starbuck, Work, Neighbors WiFi, etc and I don't have any problems staying connected on their networks.
I've had Dell on the line, we connected hardwired, and there solution was to force forget and reconnect to the router, which worked for the 10min he was on the line with me, but then failed soon after, and back in the same connectivity hell
View 4 Replies
View Related
Jun 27, 2010
A specific switch port which happens to be part of a 2 switch 3750 Switch Stack is seeing multiple CDP packets from 3 extra switch port interfaces that are not directly connected. Noteworthy is that the far end devices have the correct CDP entries and I physically confirmed at least two of those connections that lead to the switch "upstream to the culprit switch". Tricky part is that its production so room for maneuvering is limited. At some point I disabled all Ports save for the real uplink and the problem momentarily disappeared. Re-enable the interfaces problem resurfaces. Is there an explanation, technique to eliminate the culprit with minimal disruption?
View 4 Replies
View Related
Jul 18, 2012
I have a Cisco 7206VXR running 12.4(24)T3 IOS. It is configured with WCCPv2 using L2 mask redirection. I am using service groups and associated extended ACLs to select which subnets I want to redirect port 80 traffic from.
It is working fine for the subnet 192.168.1.0/24....
int gi0/2
ip wccp 10 redirect in
ip address 192.168.1.99 255.255.255.0
... however, there is OSPF running between the router and a Mikrotik device directly connected to this interface. The gateway addresses for all the client subnets are on the Mikrotik. Traffic from other subnets, e.g. 192.168.2.0/24, 192.168.3.0/24 come in on this interface and I want to redirect those too. But it appears that the redirection doesn't work for those subnets (I don't see any hits on the relevant ACL for any subnet except 192.168.1.0/24).
It seems like the router only wants to redirect traffic for subnets that it has an IP address in itself. Admittedly, all of the example configs i've found on cisco.com are for redirecting traffic from directly connected subnets but I can't find anything that denies thie possibility of redirecting any traffic that comes in on a given interface.
The question is, is this how WCCPv2 redirection works? i.e., the router must have an IP address in the subnet to be redirected?
View 1 Replies
View Related
