D-Link DIR-655 :: Determine If A Device Is Connected To LAN?
Mar 27, 2011
Should the DIR-655 list all devices that are accessing either my WAN or another device on the LAN, assuming there are no other switches on the network, and all traffic is going through the DIR-655?
I was trying to determine the IP, and MAC address of an AT&T Microcell connected to my network. I have no physical access to Microcell. I have been able to find the IP address, in the logs of the DIR-655, but nowhere else. Shouldn't it be listed under SETUP -> NETWORK SETTINGS -> NUMBER OF DYNAMIC DHCP CLIENTS?
View 2 Replies
ADVERTISEMENT
Oct 27, 2011
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
View 1 Replies
View Related
Apr 26, 2011
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies
View Related
May 14, 2013
I used the AP 1552 Link Calculator to determine the coverage area of my AP deployment, however I have some concerns.I would like to know what the maximum radio range refers to when using an omni-directional antenna. Is this distance the radius or diameter of the coverage area? [code]
View 1 Replies
View Related
Jun 1, 2012
I have a wireless network (cable modem and router) set up in my home, which all of my devices are able to connect to the internet just fine, all but two; one is a netbook and the other is a desktop. The netbook has a wireless card built in, and the desktop has usb wireless card. Both of devices are running xp (both are the only compters in my home ran on xp), and these are the only two devices that will not connect to the internet wirelessly, except for when the wireless is unsecure these two devices connect fine, but once I enable a password these two devices say connected with an excellent signal strength, but once I open up the brower no web page comes up (just a message saying server not found). These two computers are able to install automatic program updates from over the internet, but still no web page will come up.
View 3 Replies
View Related
Jun 5, 2012
My desktop's internet connection is acting up. It's always worked fine, then all of a sudden it has stopped. I can still access MSN messenger and Paltalk, perfectly fine, and it is showing that I have an internet connection. However, when I open any of my browser windows, it cannot access the internet. My laptop and ipod are connecting fine on the wireless. I have my ethernet cable from the desktop plugged into the router, which is plugged into the modem. I CAN force the connection to work by 'talking' to the modem (using the IP address) and doing a disconnect and reconnect. This lasts for a little while, then it stops again. When I do my network map, it shows an 'unknown device' where the modem is supposed to be. When I disconnect and reconnect the modem, it changes from 'unknown device' to 'switch'.
View 19 Replies
View Related
Sep 29, 2011
i have a lan connection for internet, the wireless card is used for an adhoc connection to a device that does not have internet, my pc just keeps telling me i have no internet connection because it is letting the wireless connection take priority over the lan connection
View 2 Replies
View Related
Jan 12, 2013
On rv110w, I have 4 vlans. vlan3 feeds a dumb switch and a Wireless AP. When looking at router DHCP leases, it shows devices connected that are not connected. Kinda like it doesn't refresh the list. Set to 50 leases. Questions: Is this normal? How often should it refresh? Is the DHCP time put in as minutes???
View 11 Replies
View Related
Dec 16, 2011
I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies
View Related
Jan 28, 2012
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
View 1 Replies
View Related
Jul 19, 2012
My router EA4500's Cisco Logo is Blinking and not connect with any device
View 5 Replies
View Related
Sep 14, 2012
I have several devices connected to my Linksys EA4500. Two of them are my Apple Mac Pro and my Logitech Squeezebox Radio. For some reason, in 'Device List', my Apple Mac Pro has the manufacturer 'Logitech' and the model 'Squeezebox Radio'. As for my Logitech Squeezebox Radio, it doesn't have a manufacturer nor a model. It appears that there is a mix up with these two devices. I have cross checked the IP addresses and MAC addresses displayed in Cisco Connect Cloud with those displayed on the devices and they match - so it's not a case of mixed up names. Could this be an issue with Cisco Connect Cloud?
View 1 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Sep 18, 2011
I have a very annoying problem with my Linksys WRT54G2.When I connect a wireless device (laptop, phone, TV, Ipad) to my wireless network I only see a Local connection, no connection to internet. After resetting the router (power off for several seconds) the internet-connection is available again.I have to do this every 1 - 2 days.
View 7 Replies
View Related
Dec 20, 2012
In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.
View 6 Replies
View Related
Dec 18, 2012
I'm the sole IT worker at this company and I specialize in everything but big, corporate networking so here's a dumb question. How do I determine the IP address of one of our two switches? I need a list of MAC addresses of connected devices so I can relabel all the cables that were mislabeled (and this is a managed switch). For the other switch, which was put in by someone who knew what they were doing, you just type ss3900 into a browser and tada, 3com Superstack 3900 login so apparently someone did some fancy DNS stuff or whatever.
For this HP Procurve, the idiot before me who got fired for completely screwing up everything didn't leave any documentation or labeling and didn't use the same IP address as the Cisco switch that was pulled out. Obviously the switch is invisible to my PC from an IP standpoint
View 15 Replies
View Related
Aug 30, 2011
I have a site with a 1700 router connected to a 2960 switch. For some of the computers on site I want to determine how much traffic is local to the LAN and how much is going across the WAN.
One strategy I've come up with is to reset the interface counters on the switch ports to the machines in question and after some time compare the total bytes in and out of the interface with netflow data from the router. My only concern is that netflow is not completely accurate about the amount of data that has passed through an interface.
Is there a better or more accurate way to accomplish my goal?
View 7 Replies
View Related
Dec 13, 2012
J've just bought an Asus RT-N66U router and I'm setting up a broadband credit card machine to go into it (rather than transmitting data over the phone line).I need to know what the status of DHCP and MAC are on the router but I'm not sure how to find it.DHCP needs to be on and MAC needs to be off.
View 3 Replies
View Related
Jan 2, 2013
Here's the situation, 2 houses, house #1 has internet, DIR-665 connected to Cable modem, between the 2 houses CAT 6 cable, house #2 has DIR-655. Both houses need to offer wireless. How should the DIR-655 (house#2) be set up? (SSID/DHCP/UPNP/IP/GATEWAY/SUBNET, etc)?
View 1 Replies
View Related
Aug 30, 2011
I have a Netgear media player that I need to keep separate from my LAN. I have a switch that's connected to WAN and from the switch to dir-655 and the Netgem box. So I have two IP:s and the Netgems traffic is not going through the router at all.Now I'm short of LAN ports and I bought an eight port switch. However I only have room for keeping two devices at the space they are at. So I need to get rid of the old switch and somehow manage the network(s) with dir-655 and the new switch.The way I see it, I should connect WAN to dir-655 and from there to the switch and connect the Netgem box to router. But how can I configure dir-655 so that the Netgem is not on LAN with other devices?
View 6 Replies
View Related
Jul 20, 2011
Do you know an easy way to determine the physical location of the device were an IP address is attached? IP Geo location doesn't work well.Is something like this possible? I know it could be if you are the network administrator and know the location of your equipment and stuff.
View 12 Replies
View Related
Nov 23, 2011
I was attempting to troubleshoot a logon problem with some machines, when it was finally revealed that there was a managed switch between the host and the target preventing this.
How would I detect this in the future? (A tracert showed nothing between host and target.) Would Wireshark show me this info, with reduced TTLs?
getting a picture of all devices between a host and a target?
View 10 Replies
View Related
Dec 29, 2011
my husband gave my son a sim card for his phone and I have no idea what the number is. This is what I found on the sim card and need the number for this to see if it is valid.
View 1 Replies
View Related
May 25, 2012
How do I determine the speed of my wireless components?
View 2 Replies
View Related
May 18, 2011
problem is my brother has been playing with its config page. he changed the IP Address of the modem and disabled DHCP. he forgot what IP Address he inputted on the config page. I tried resetting the router with the small button on its side. Nothing happens. all the lights blink when i pushed the reset button for 10 sec. but nothing happens. i still can't access its default IP which is 192.168.1.1 IS there anyway to determine its IP Address even if DHCP is disabled ?
View 5 Replies
View Related
Apr 9, 2012
I have an old Compaq PC that's running Windows XP SP3 and for quite some time has not had problems with networking or using this wireless adapter. But not long ago the network interface disappeared and the adapter was now being shown in the Device Manager as an unknown device. If you pulled the adapter out and reinserted it you'd get a message on screen that would say something to that effect.
There are two computers next to each other that both use this exact same adapter and I've tried swapping them between the PCs to see if one adapter worked better than another. They both work in one PC and neither work in the PC I'm having trouble with.
View 1 Replies
View Related
Feb 8, 2011
I had a Linksys BEFSR41 router with AppleTV 1stGen with 0 problems.Now I have a DIR-655 Vb1 2.00NA firmware and itunes now cannot find the AppleTV as a device. I have tried resetting the AppleTV to factory defaults re-installing latest firmware and reinstalling itunes, powering down all devices etc., and no way can itunes find the appleTV although the appleTV is on the net and seen by the router.I have gone to a wired connection to the router too because the router kept dropping the wireless connection to the router too. Of course I got the DIR-655 for wireless
View 15 Replies
View Related
Apr 5, 2012
I have a media player wired to my dir-655. I have a wrt300 on the same network to use for vpn. I live in Canada, and to use Netflix etc, from the US, I need to use the vpn.Is it possible to have the media player routed through the wrt300, rather than discovering all the IP addresses for Netflix etc and routing each one?
View 3 Replies
View Related
Dec 5, 2010
I have a "vpn device" (that is what they called it to me) basically its a custom no-name black box with a lan and a wan port that my office gave me. It is running url... vpn connection to my office automatically so no computers have to run a vpn client locally. "It just works".Previously I had a DL 4300 set to bridge mode so I could get wifi. VPN device doesnt have wifi
I replaced the DL-4300 with a 655 because I wanted N speed for wifi and I got a DAP 1522 to wirelessly bridge my dvr and a htpc.I have read through the many threads of the 655 and bridging and it being removed and I'd love to use the 655 as my router to take advantage of all the other routing features, but alasSo here is my setup as of now, they set my vpn to be 10.86.83.1 so that is my network.Cable Modem -> pfSense -> switch ->
-> office computers and printers
-> DL 4300 10.86.83.2 (I'll soon disable this and remove it, or maybe setup another remote ap in future)
-> DIR 655 10.86.83.3 (using Lan port not wan port)
Laptops/phones connecting to new 655 wireless SSID, however I'm not sure how you tell if its using the DAP1522 or the 655 or is that just seemless and I shouldnt know?Also I couldnt get a dhcp via the 655-> ... -> DAP 1522 from the pfSense router. So I just enabled DHCP on the 655 and now I get ip and internet access.Really have no idea how that is working having 2 DHCP servers, but I guess they are smart about it (for now..or just lucky)
View 1 Replies
View Related
Jan 19, 2011
I have a D-Link DIR-655 REV.B and have no luck getting my Nettalk Duo device to work with it. I have tried forwarding all of the needed ports and even placing the device in the DMZ but can't get it to work with this router. I have noticed that this router has no way to disable SIP ALG which should eliminate the issues I am having. Why would D-Link give us no way to disable this "feature" that is known to cause issues with VOIP devices?
View 14 Replies
View Related
Mar 28, 2012
I am new to Cisco Nexus and recently my company auditor flagged out that IPv6 is enabled on our Cisco Nexus 7000 device when we are not IPv6 ready.
The auditors have flagged this out due to the following default CoPP configuration:
ipv6 access-list copp-system-acl-bgp6
ipv6 access-list copp-system-acl-hsrp6
ipv6 access-list copp-system-acl-icmp6
ipv6 access-list copp-system-acl-icmp6-msgs
ipv6 access-list copp-system-acl-ntp6
ipv6 access-list copp-system-acl-ospf6
ipv6 access-list copp-system-acl-pim6
ipv6 access-list copp-system-acl-radius6
ipv6 access-list copp-system-acl-ssh6
ipv6 access-list copp-system-acl-tacacs6
ipv6 access-list copp-system-acl-telnet6
ipv6 access-list copp-system-acl-tftp6
Does the default CoPP enable IPv6?
View 4 Replies
View Related
Feb 8, 2012
How to determine why my HP Pro-curve switch randomly faults and resets during the day, about 3 to 5 times?
View 5 Replies
View Related
