Cisco :: Determine If IPv6 Is Enabled On Nexus?
Mar 28, 2012
I am new to Cisco Nexus and recently my company auditor flagged out that IPv6 is enabled on our Cisco Nexus 7000 device when we are not IPv6 ready.
The auditors have flagged this out due to the following default CoPP configuration:
ipv6 access-list copp-system-acl-bgp6
ipv6 access-list copp-system-acl-hsrp6
ipv6 access-list copp-system-acl-icmp6
ipv6 access-list copp-system-acl-icmp6-msgs
ipv6 access-list copp-system-acl-ntp6
ipv6 access-list copp-system-acl-ospf6
ipv6 access-list copp-system-acl-pim6
ipv6 access-list copp-system-acl-radius6
ipv6 access-list copp-system-acl-ssh6
ipv6 access-list copp-system-acl-tacacs6
ipv6 access-list copp-system-acl-telnet6
ipv6 access-list copp-system-acl-tftp6
Does the default CoPP enable IPv6?
View 4 Replies
ADVERTISEMENT
Apr 9, 2013
I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
- I have tried to reset the router both by holding the reset button and through the configuration application.
- I have enabled and disabled wireless to see if that was slowing things down
- I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500)
- I tried putting the computer in the DMZ
- I have changed the ports that the computer is plugged into
- I have disabled and enabled IPV6 on both router and network card
- Firmware version - 1.1.38.134141
View 9 Replies
View Related
Dec 9, 2012
Should I install any special license to enable vrf within Nexus 7000 VDC? I observed that vrf routing instance is not enabled in the VDC.
View 2 Replies
View Related
Nov 23, 2011
Does Nexus 7000 support ipv6 6to4 tunnel?
View 3 Replies
View Related
Aug 30, 2011
I have a site with a 1700 router connected to a 2960 switch. For some of the computers on site I want to determine how much traffic is local to the LAN and how much is going across the WAN.
One strategy I've come up with is to reset the interface counters on the switch ports to the machines in question and after some time compare the total bytes in and out of the interface with netflow data from the router. My only concern is that netflow is not completely accurate about the amount of data that has passed through an interface.
Is there a better or more accurate way to accomplish my goal?
View 7 Replies
View Related
Dec 18, 2012
I'm the sole IT worker at this company and I specialize in everything but big, corporate networking so here's a dumb question. How do I determine the IP address of one of our two switches? I need a list of MAC addresses of connected devices so I can relabel all the cables that were mislabeled (and this is a managed switch). For the other switch, which was put in by someone who knew what they were doing, you just type ss3900 into a browser and tada, 3com Superstack 3900 login so apparently someone did some fancy DNS stuff or whatever.
For this HP Procurve, the idiot before me who got fired for completely screwing up everything didn't leave any documentation or labeling and didn't use the same IP address as the Cisco switch that was pulled out. Obviously the switch is invisible to my PC from an IP standpoint
View 15 Replies
View Related
Dec 13, 2012
J've just bought an Asus RT-N66U router and I'm setting up a broadband credit card machine to go into it (rather than transmitting data over the phone line).I need to know what the status of DHCP and MAC are on the router but I'm not sure how to find it.DHCP needs to be on and MAC needs to be off.
View 3 Replies
View Related
Jul 20, 2011
Do you know an easy way to determine the physical location of the device were an IP address is attached? IP Geo location doesn't work well.Is something like this possible? I know it could be if you are the network administrator and know the location of your equipment and stuff.
View 12 Replies
View Related
Nov 23, 2011
I was attempting to troubleshoot a logon problem with some machines, when it was finally revealed that there was a managed switch between the host and the target preventing this.
How would I detect this in the future? (A tracert showed nothing between host and target.) Would Wireshark show me this info, with reduced TTLs?
getting a picture of all devices between a host and a target?
View 10 Replies
View Related
Dec 29, 2011
my husband gave my son a sim card for his phone and I have no idea what the number is. This is what I found on the sim card and need the number for this to see if it is valid.
View 1 Replies
View Related
May 25, 2012
How do I determine the speed of my wireless components?
View 2 Replies
View Related
May 18, 2011
problem is my brother has been playing with its config page. he changed the IP Address of the modem and disabled DHCP. he forgot what IP Address he inputted on the config page. I tried resetting the router with the small button on its side. Nothing happens. all the lights blink when i pushed the reset button for 10 sec. but nothing happens. i still can't access its default IP which is 192.168.1.1 IS there anyway to determine its IP Address even if DHCP is disabled ?
View 5 Replies
View Related
Mar 27, 2011
Should the DIR-655 list all devices that are accessing either my WAN or another device on the LAN, assuming there are no other switches on the network, and all traffic is going through the DIR-655?
I was trying to determine the IP, and MAC address of an AT&T Microcell connected to my network. I have no physical access to Microcell. I have been able to find the IP address, in the logs of the DIR-655, but nowhere else. Shouldn't it be listed under SETUP -> NETWORK SETTINGS -> NUMBER OF DYNAMIC DHCP CLIENTS?
View 2 Replies
View Related
May 22, 2013
I have an AIR-LAP1242AG-A-K9, serial number FTX1623B0RX. I just need to know how old this unit is. (I haven't attached it to our Cisco account, so I can't open a TAC for it.)
Boot Version 12.4.13.0 IOS Version 12.4(23c)JA5Mini IOS Version 3.0.51.0
View 2 Replies
View Related
Dec 8, 2012
In the bottom screenshot how to determine the coverage level, I couldn't find any explicit documentation on that .
View 3 Replies
View Related
Feb 8, 2012
How to determine why my HP Pro-curve switch randomly faults and resets during the day, about 3 to 5 times?
View 5 Replies
View Related
Jan 27, 2012
I'm am using Google Analytics for my webpage, and I want to exclude(filter) the IP range of my router's external IP addresses from the Analytics data. How do I determine the IP range of my router's public IP?
View 4 Replies
View Related
Jan 14, 2012
The support and registration pages for the E4200 wireless router ask whether I have a V1 or V2 router. There is no place on the actual router that identifies it as V1 or V2, and the Cisco Connect application doesn't display this infomation either. What I do know is the following:
Model name: Linksys E4200
Model number: E4200
Serial number: 01C10C18104423
Firmware version: 1.0.03 build 14
Software version: 1.4.12005.2
How do I determine if this is a V1 or V2 router? The software updates are version specific.
View 9 Replies
View Related
Apr 27, 2011
I'm attempting to configure qos on our ASA 5505 and I'm not sure how to determine what our average and burst rates should be.The applications being used will be RDP over a ipsec tunnel, so it is somewhat sensitive to latency.The final setup will be a 1.54Mb T1 line, but in testing I have a DSL connection with .70Mb U/L speed.
View 3 Replies
View Related
Jun 13, 2013
We are trying to replace the CSS between our firewall and DMZ with a BigIP. Among it's other functions, it will act as the router between the firewall and the DMZ. To make this work, I need to assign vlan tags values for the vlans I create on the BigIP box and these must match the tags on the cisco switches (3550's) How do I find this information on the switch?
View 2 Replies
View Related
Jun 27, 2004
Im trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?
View 4 Replies
View Related
Mar 12, 2013
I would like to ask if how can we determine by mear physical inspection if the power supply of a CISCO2911/K9 router is AC, POE or DC? Do we have images of the actual spare power supply?
View 3 Replies
View Related
Aug 13, 2012
Do they have a default IP assigned to them?
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).
View 15 Replies
View Related
Jun 17, 2012
I have a client devices constantly sending data (~ 13 kb per second) to a server through a Cisco AP1241AG (802.11g).I use Iperf to test throughput, but I am having a difficult time determining what an acceptable throughput rate would be.I know in "theory" the best throughput rate I could get is 54 Mbps, but since my client devices only send 13 kbps is 1 Mbps more than enough? or is 13 kbps the low limit for my throughput test?
View 1 Replies
View Related
Oct 22, 2012
how do i determine the ip address manually when installing my hp printer. model ; P3005x
View 3 Replies
View Related
Oct 30, 2012
How can I determine my DIR 601 router signal strength ?
View 2 Replies
View Related
Nov 8, 2012
I have a list of email addresses, people who have subscribed to a free electronic newsletter. The email address is all the information we have about each subscriber.A satellite office is going to begin handling print and electronic subscriptions for subscribers in Peru. Is there any way to determine which of these email addresses are from Peru?
View 5 Replies
View Related
Mar 8, 2012
Is there a free scan to determine ipaddress of westell7500 router?
View 3 Replies
View Related
Apr 2, 2011
I have the BEFSR41 v2 Router and am trying to determine if I have the latest Firmware vrsion - am having a few connection problems.
View 1 Replies
View Related
Jan 12, 2012
I am not very computer literate, so this will seem like a stupid question. How do I determine whether a computer has wireless connectivity?
I have a Dell Dimension 9200 running Windows Vista that I bought in 2007. Previously, I have connected it to the internet using an ethernet cable to my router, but this is no longer possible now that my new computer is using the ethernet connection. I want to establish a wireless connection between my older Dell Dimension 9200 and my router, but I don't know how to find out whether the computer is capable of wireless connectivity.
View 3 Replies
View Related
Sep 29, 2011
I have an E1000 linksys router. I am trying to determine the admin password. I have looked at seeral entries regarding this. I do not have CICSO connect installed. Not sure why. The router works fine. I have the CD that came with the router. I have also downloaded current version of connect software. Both of them want to config the router. The first item asked for is the admin password. I know I press reset button. I am trying to retrieve password without doing that.
View 1 Replies
View Related
Feb 23, 2011
We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies
View Related
Mar 15, 2013
I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
View 12 Replies
View Related
