Linksys Wireless Router :: EA3500 Disabled And Enabled IPV6 On Network Card
Apr 9, 2013
I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
- I have tried to reset the router both by holding the reset button and through the configuration application.
- I have enabled and disabled wireless to see if that was slowing things down
- I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500)
- I tried putting the computer in the DMZ
- I have changed the ports that the computer is plugged into
- I have disabled and enabled IPV6 on both router and network card
- Firmware version - 1.1.38.134141
I have to go back into settings and deactivate the IPV6 tunnel daily to keep access to youtube. My provider does not support IPV6. Saving changes has no effectIs there a way to ensure that the IPV6 tunnel remains deactivated?I have firmware version 1.0.30 build 126544 2011-12-24. Firmware update function says I got the latest version.
Region : Ireland Model : TL-MR3420 Hardware Version : V2 Firmware Version : ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
Using a Mac running Mac OS X 10.6.8 with VPN Tracker 6.3.0.Before switching to the WAG320N I had no issues with my IPSEC VPN client. After the switch it consistently fails in Phase 1 negotiation.In the log file of the gateway I only notice: Mon, 2011-08-22 07:47:31 - [Outgoing] UDP Packet - 192.168.1.100:500 --> IP.ADDRESS.VPN.GATEWAY:500.The software itself complains about timeouts while contacting the remote gateway.VPN pass through is enabled, no port forwarding is set up, firewall is disabled.
I have disabled / enabled and unistalled / installed and updated driver software but to no avail.It has been replaced, I have refreshed TCP/IP as per previous instruction found here and it did go a bit further, but now stuck as per below from CCX diagnostics Utility:
I had it working fine up until i decided to install a new harddrive on my xp pro machine. but to the point, when i connect to the 3g card its fine, but if i try to enable the lan at the same time it disconnects my 3g card. my problem isnt how to network two computers, its how to get lan and a usb modem working simultaneously. i have tried to enable ics, then reboot. same results. if i can get the lan to stay on while the 3g card is on i have the rest whooped.it is some kind of setting somewhere. maybe i need to install windows 2003 server or something like that.
I press FN/F2 to "enable and disable wireless" but cannot see the antenna icon appear on the screen to know if the functionalty even exists. Other function keys work properly. I vaguely remember seeing this icon when I first purchased the laptop, but soon after purchase I had to completely reinstall the operating system and have not had a need to a wireless connection to notice it was no longer there.Because I cannot access wireless connections I assume there is a problem with enabling this feature of my laptop.
what I should be doing to check/correct that my laptop can receive a wifi connection? I've checked the recommended driver installs for my model of laptop, but nothing seems relevant.
Ever since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
I am having no end of issues with this router since the upgrade to CCC. I don't want to downgrade because the reason I purchased the router was for the hopeful addition of more apps later on and the CCC.
My router has now suddenly decided to no longer broadcast N signals. My 2.4ghz network is set for mixed and my 5ghz is set for N Only. They are both set to auto channel and WPA2 Personal security and have been working since I purchased the router on Sunday.
Last night it spontaneously rebooted and that was that.
Both laptops (with N adapters) are seeing the 2.4ghz network as 802.11g and my 300Mbps notebook adapter is seeing the 5ghz network as 802.11a. InSSIDer is showing that both networks are now broadcasting at a max of 54Mbps.
I have tried rebooting the router multiple times. I have also tried unplugging it for 60 seconds. I have also attempted to force the 2.4ghz to 20Mhz and a more optimal (unused) channel. That doesn't work. I tried setting the 5ghz network to wide (40mhz) with an optimal channel. Same deal. Still seeing it as 802.11a.
I have just bought the EA3500 3 days ago.Also, I have been trying to find the way to rename the Guest Network to something without the -guest prefix.[url]....
I am having a HP Laptop with Windows Vista 64 bit OS. Since today I am having problem with my wireless network adapter card. It is remaining disabled and not getting enabled. I uninstalled the driver as well as disable the card but it is not working. The problem is Quick launch button on HP laptop for wireless card is showing as enabled but my network center shows it as disabled.
Just purchased new N750 model EA3500-NP and everything went ok until I tried to get my HP Laser Jet P2035n online. No go! It worked fine on the D-Link via Ethernet connection.
Experienced problems with guest network not showing up as an available network on a device (laptop, iPad, etc)?I double checked if guest network is enabled on a EA3500 router. What other steps can I take?
I'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?
Just got a new EA3500, and plan to use its guest network feature to allow Internet access but not access to my LAN. Wondering if I can set it up so that users on the guest network bring up a particular website when they open their browser.
I just setup my EA3500 router and both SSID's are the same.Is this ok or should I give them unique names?Since they are the same what are my products connecting to?If I do separate them, what item should connect to what network?
I just bought a Linksys ea3500 and i'm trying to configure it.This is the case.I have a first router connected to internet and several computers connected to it.Then, I have a second router (ea3500) also connected to it.If i disable the dhcp and use it as an access point i can see all computers in the network.If if enable the DHCP it creates a private network and all pcs connected to this network can't see and access computers of the first network.The problem is that using EA3500 as an access point disables the most part of the features of the router.My question is: can i use it not as an access point (in order to have all features) but at the same time having access the first network and all computers on it?
I have been trying to get Airprint to work in our network. Topology is a 255.255.255.254.x network that has mostly wired with wireless all under the same subnet. Airprint will not discover printers if on the WLC2106 WiFi network but if the iPad or iPhone is connected to some small Linksys WiFi router, it works.
What should be enabled or disabled on the WLC2106 to get Airprint to work?
Brand new MSI system using windows 7. we're using a wirless network in the house, and up until today it's been fine. Randomly, Windows is no longer detecting any networks.
I've confirmed there is no prob with the router or signal as I can detect the network in my room and connect to the internet (using a homeplug hardline). I've tried enabling and disabling both the router and wireless card, a system restore (windows made no changes), and when I came to use the windows 7 troubleshooter - it says the device is not enabled?
When I click on the Wireless Network Connection icon it says "Wireless network unavailable." There's also an error message that says "The Dell Wireless WLAN Card is disabled. Use the Dell Wireless WLAN Utility to enable it." When I right click on the wireless network icon it says "No wireless networks were found in range. Make sure the wireless switch on your computer is on. To see an updated list, click 'Refresh network list.'" I don't have a wireless switch. I have a wireless enable icon and it says Enabled. My wireless network is working because my phone sees it and two other networks in the neighborhood. I couldn't find the Dell Wireless WLAN Utility. I also tried my iPhone hotspot. Laptop did not detect it either.
I just purchased an AE2500 today for my desktop computer because my router is in another room. I am running Windows 7 64 bit. I tried installing the software from the disk first and it would not detect the adapter. But Windows did detect the device and I was able to manually install the drivers and in the control panel it says the device is working properly. When I go to the network sharing center no network is detected I then go to the netwokr adapters and the device is disabled. I try enabling the device and it will not. So then I go and boot in to Windows 8 RC and the device is detected and works fine and everything seems fine. I downloaded the driver from the website tried uninstalling the driver and reinstalling it with the downloaded version and still a no go.
HP Pavilion dv7-6135dx Ent Pc Win7 Home Prem 64 Motorola Surfboard Modem Linksys EA3500 Router Netgear 10/100 24 port switch
my wife bought me this EA3500 for Father's Day this year. It's only been hooked up for a couple of weeks (we were in the middle of a move during Father's Day), but now I have no wifi on either band. My wife can no longer connect to it either. We have tried completely resetting it, we have reset the modem, the switch, laptops, everything. Still no wifi. It worked out of the box, but now we have nothing. Does HP needs a certain type of driver? Our iPhones show connected and surf the brower's and FB app with no issues while in wifi mode, but then again, I can pull the ethernet from the internet port and the phone's still show connected (good job, iOS).Cable from main splitter runs to basement where the modem is located. Modem ethernet feed up a wall to a wall plate where the router is. Router then feeds back to the switch. The switch then sends the IP throughout the house for the LAN lines, and the EA3500 feeds all of the wireless devices (used to). So, Cable box, modem, router, switch. Router is currently good for LAN only. I am connected to it via LAN right now, 2 feet from my laptop.
In connections:IPv4/IPv6 both "No Internet Access" (for IPv4, if you change a setting in the setup, it becomes "Internet Access" for about 3 seconds.)Media State: EnabledSpeed: Alternates between 72Mbps and 144Mbps
In my home network, I have a Synology. It has 10.0.123.123 as local IP address on my local network and it can be accessed by internet with the dynamic domain name.So when I'm home, I have to use 10.0.123.123 to access it, and when I'm away, I have to use trucmuche.diskstation.me.Would it be possible to configure the EA3500 to redirect the domain name "trucmuche.diskstation.me" to 10.0.123.123 when I use the domain name inside my home ?A friend told me that I had to configure "loopback" but I don't know how..
The guest network on the router keeps going down. It can be seen but it cannot be connected to. Sometimes it works for a day or 2 and then it doesn't. I have to constantly babysit the network and it is entirely frustrating because the only fix is to reboot the router.I have tried factory resetting several times.I have tried re-flashing the fw.I'm using the non-CCC fw because CCC had way, way too many issues.These routers have been out for months and many people have been having issues and somehow Cisco doesn't see fit to work on firmware that stabilizes them at all? It's like, they release a router and then forget about it - the next batch comes along, often the same guts with a different shell and it's the same thing over again. I had a WRT610N and I said I'd never buy another Cisco after that but I broke my rule because of being lured by these "App enabled" features, which mind you have nothing at all over the competition since the CCC doesn't even work for most people.
I have a EA3500 wireless router with the new style (smartwifi) firmware. I've scoured the web admin interface and can't find any sort of 'status' page that would tell me the external IP. I've looked through the support docs but they only show how to find internal/local IP.
I have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
If someone has the original firmware for the EA3500 to copy. I need to downgrade my router after Cisco sabotaged it with their Cloud Connect. This will be the firmware you have right out of the box. Be sure you go into the Admin. section and Save a Copy before you ever connect to the Internet. Also Uncheck the Auto Updates box or you will be fed the Cloud Connect (and its amazing Terms Of Service).
Windows 7 64 bit / Linksys EA3500 / (2) FosCam F18910W IP Camera’s I just installed a new EA3500. (Should I have purchased the 4500)?I need to set up port forwarding to enable wireless use of the IP cams with my iPhone. I had this all set using my former router, but it died.how to to port forward this Linksys EA3500?
