I have to go back into settings and deactivate the IPV6 tunnel daily to keep access to youtube. My provider does not support IPV6. Saving changes has no effectIs there a way to ensure that the IPV6 tunnel remains deactivated?I have firmware version 1.0.30 build 126544 2011-12-24. Firmware update function says I got the latest version.
View 5 RepliesRegion : Ireland
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
- I have tried to reset the router both by holding the reset button and through the configuration application.
- I have enabled and disabled wireless to see if that was slowing things down
- I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500)
- I tried putting the computer in the DMZ
- I have changed the ports that the computer is plugged into
- I have disabled and enabled IPV6 on both router and network card
- Firmware version - 1.1.38.134141
Need a guide to setting the Ipv6 Tunnel from SixXS On the cisco connect cloud?
View 2 Replies View Relatedi have my Cisco E4200 set up with a 6rd tunnel. the tunnel seems to work fine for the most part. i can ping ipv6.google.com and get a response.however, i cannot ping the addresses of the IPv6 Tunnel ends from within my network. If i run a ping from outside the network, i can ping the IPv6 address of the server end, however, i cannot ping the E4200's end of the tunnel. is there a specific option that needs to be set? i have allowed ping so that my IPv4 address is pingable, am i missing something for IPv6?
View 7 Replies View RelatedI try to let Cisco ASA automatic select a tunnel group for users, after user input username and password. I try to do this without user selection a connection profile on login page. Authentication on ASA<>ACS 5.3<>MS AD. How i can will do this? Radius attribute class=group_policy don't work.
View 1 Replies View RelatedMy router automatically sets the wireless network settings to the original default. Sometimes after 1 hour sometimes after a week. It resets to automatic instead of the manulal settings I use for configuration. Changes the SSID to Linksys and disables wireless security.
View 5 Replies View RelatedI just got a linksys after years of using a single netgear, this is the second we've gotten in the last month... But each time we have the same problem, the thing resets constantly while doing streaming from netflix, over wifi, and resets the entire router. I've updated to the latest firmware but i'm ready to just throw this out and put our old netgear back up.
View 4 Replies View RelatedI have a WRT54GS wireless router. I can successfully set up the router with my DSL modem for PPPoE. Here's my problem. The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically. I DON'T want it to do that. Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?
View 1 Replies View RelatedI am working with a WRT320N for some weeks now, but I don't get the fact that 40Mhz channel width is only allowed for Automatic channel selection.I keep losing connection and the channel keeps changing.I want an option to change the channel manually (like in every good WLAN router!!), also with N data rate (40Mhz channel width).I know how to select the best channel, so why aren't I able to change it the way I like it?
View 4 Replies View RelatedI've had my WRT54GL for a couple of months now, and it keeps wiping my saved settings and reverting back to the default. It works fine with all devices for a week or so after the initial set-up, then will only work on the system that is wired.
View 1 Replies View RelatedI have a WRT100 wireless router, which is configured for a PPPOE connection to my ISP. After running one of the tools to determine responsiveness of DNS name services, I would like to manually configure my DNS services, placing a more responsive service as my first DNS choice. In the router administration, I can configure three static DNS IP's. However, I don't see any place in the configuration to turn off the automatic DNS configuration from my ISP. So, when I issue an IPCONFIG /ALL on my computer, the DNS listing shows two DNS Name Services from my ISP ahead of the three static DNS IP's that I configured.
View 3 Replies View RelatedI am curious as what the packet size should be set . is the bigger size == lower speed smaller == faster or just leave automatic setting for packet size?
View 4 Replies View Relateddo external hard disks automatically spin down after a period with no access/use when connected with the USB port of the WRT160NL?
View 1 Replies View RelatedI am trying to determine the best way to setup my E4200 V2 so that it is “uplinked” correctly to a Comcast Dory Modem/router. Currently we have the E4200 V2 router plugged into the Comcast Dory Modem/Router using a CAT6 cable from one of the Ethernet ports on the Comcast device to the WAN port on the E4200. The E4200 is set to “Automatic Configuration - DHCP.”
We are trying to do two things. First better WIFI in the center of the house and for a TV located next to the Comcast device, and second, have all devices in this house see and access all other devices including the Samsung SmartTV, my son’s two systems upstairs, the 3 systems in the room with the E4200, and the one network printer. In the room with the E4200 we have 3 computers and one network printer. 3 of those 4 devices support WIFI so we don’t have to use all 4 Ethernet ports on the E4200.
I see others talking about running the CAT6 cable to an Ethernet port on the E4200 instead of the WAN port and setting it to “Bridge Mode.” Right now the system appears to be working fine although we are sometimes experiencing brief dropped connections with the devices hardwired into the E4200.
Should I be running the E4200 in “Bridge” mode or “Automatic DHCP” mode and which port on E4200 should the CAT6 from Comcast be plugged into?
setup an external hard drive with music on on the usb port on my EA3500 and actvated ftp but I cant access it from the net.
View 1 Replies View RelatedFor hours i tried to find info online of how to access QoS on EA3500 router. I cannot find it on the cisco connect cloud page.
View 1 Replies View RelatedSystem:
HP Pavilion dv7-6135dx Ent Pc Win7 Home Prem 64
Motorola Surfboard Modem
Linksys EA3500 Router
Netgear 10/100 24 port switch
my wife bought me this EA3500 for Father's Day this year. It's only been hooked up for a couple of weeks (we were in the middle of a move during Father's Day), but now I have no wifi on either band. My wife can no longer connect to it either. We have tried completely resetting it, we have reset the modem, the switch, laptops, everything. Still no wifi. It worked out of the box, but now we have nothing. Does HP needs a certain type of driver? Our iPhones show connected and surf the brower's and FB app with no issues while in wifi mode, but then again, I can pull the ethernet from the internet port and the phone's still show connected (good job, iOS).Cable from main splitter runs to basement where the modem is located. Modem ethernet feed up a wall to a wall plate where the router is. Router then feeds back to the switch. The switch then sends the IP throughout the house for the LAN lines, and the EA3500 feeds all of the wireless devices (used to). So, Cable box, modem, router, switch. Router is currently good for LAN only. I am connected to it via LAN right now, 2 feet from my laptop.
In connections:IPv4/IPv6 both "No Internet Access" (for IPv4, if you change a setting in the setup, it becomes "Internet Access" for about 3 seconds.)Media State: EnabledSpeed: Alternates between 72Mbps and 144Mbps
In my home network, I have a Synology. It has 10.0.123.123 as local IP address on my local network and it can be accessed by internet with the dynamic domain name.So when I'm home, I have to use 10.0.123.123 to access it, and when I'm away, I have to use trucmuche.diskstation.me.Would it be possible to configure the EA3500 to redirect the domain name "trucmuche.diskstation.me" to 10.0.123.123 when I use the domain name inside my home ?A friend told me that I had to configure "loopback" but I don't know how..
View 3 Replies View RelatedThe guest network on the router keeps going down. It can be seen but it cannot be connected to. Sometimes it works for a day or 2 and then it doesn't. I have to constantly babysit the network and it is entirely frustrating because the only fix is to reboot the router.I have tried factory resetting several times.I have tried re-flashing the fw.I'm using the non-CCC fw because CCC had way, way too many issues.These routers have been out for months and many people have been having issues and somehow Cisco doesn't see fit to work on firmware that stabilizes them at all? It's like, they release a router and then forget about it - the next batch comes along, often the same guts with a different shell and it's the same thing over again. I had a WRT610N and I said I'd never buy another Cisco after that but I broke my rule because of being lured by these "App enabled" features, which mind you have nothing at all over the competition since the CCC doesn't even work for most people.
View 9 Replies View RelatedI have a EA3500 wireless router with the new style (smartwifi) firmware. I've scoured the web admin interface and can't find any sort of 'status' page that would tell me the external IP. I've looked through the support docs but they only show how to find internal/local IP.
View 2 Replies View RelatedI have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
View 9 Replies View RelatedIf someone has the original firmware for the EA3500 to copy. I need to downgrade my router after Cisco sabotaged it with their Cloud Connect. This will be the firmware you have right out of the box. Be sure you go into the Admin. section and Save a Copy before you ever connect to the Internet. Also Uncheck the Auto Updates box or you will be fed the Cloud Connect (and its amazing Terms Of Service).
View 6 Replies View RelatedWindows 7 64 bit / Linksys EA3500 / (2) FosCam F18910W IP Camera’s I just installed a new EA3500. (Should I have purchased the 4500)?I need to set up port forwarding to enable wireless use of the IP cams with my iPhone. I had this all set using my former router, but it died.how to to port forward this Linksys EA3500?
View 2 Replies View RelatedI have recently bought a cisco EA3500 router for my home network and i am pretty surprised to see that a router from the world leader in the networking domain cannot perform as expected.
The first problem i had was that the network (wired and wireless) was dropping from time to time for a couple of minutes with the power led of the router blinking. I turned off the log feature of the router and it seems that until now the problem is resolved.
Now, the second and, at least as annoying as the first, is that i have a 640gb usb hdd connected to the router, formatted NTFS. It seems that every now and then a file gets corrupted, that is, it is transformed into a folder! And it cannot be recovered without pulling out the hdd and using a 3rd parth software for file recovery.
I have the latest firmware. Should i switch back to the classic firmware instead of the "fancy" new one? I really need my files on that drive, so i cannot risk loosing them in this random manner.
I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies View RelatedI am unable to connect a printer using the USB port on my new Linksys EA3500 router.
I followed the directions here: Support Page , but my verison of Cisco Connect does not have the option to "connect a USB printer".
I am on a macbook pro running OSX 10.7.4 and my verison of Cisco Connect is 1.4 (12005.2). My router's firmware version is 1.0.30.126544. A screenshot of what I see after clicking "add a device" in Cisco Connect is below. The printer is an HP DeskJet F4280.
after updating to smart wi-fi I can't access the USB FTP or off network.Only way it's accessible is from the computer the router is attached to via network drive.FileZilla gives me this error....."Connection attempt failed with "ECONNREFUSED - Connection refused by server".I've reset the router same problem.
View 9 Replies View RelatedAfter using the newest firmware for CCC, I've found it is very convenient, but only in some ways. Now, I think I find it is uncomfortable, very disappointed and waste lot of times. Each time I try to access to CCC, it took me like 5 mins to access the web page. I understand ciscoconnectcloud.com is use when you are outside of your home network, but when I access it directly from my home (local IP), why should I need to connect via a CCC(?) I want a local connect to my router which is a faster access than via a server.
Sometimes, connect via an IP of the router, it say can't connect because of internet connection down, but actually I can still access internet except access my own router. I like the easy setup of CCC but maybe I need to switch back to non-CCC?
I bought a new router today because my WRT54GL was giving me some fits. I purchased an EA3500 and I'm using an EA2500 adapter on the desktop since the router can't reach it via ethernet. Some of my early troubles with this combo began with not being able to test upload bandwidth. It would just time out and give an error via the built in Cisco (OOKLA) utitliy and through speedtest.net after which, the network would show no internet access and I'd have to reset the adapter. After trying to troubleshoot that issue it grew into zero internet access for my desktop however my Nexus would have wifi access without issue. If I'd startup in safe mode with networking I'd have net access shortly and then it would quit about 30 seconds after startup. I've tried uninstalling all drivers for the wireless NIC and the Cisco Connect software while doing everything manually but nothing changes. This PC simply won't gain internet access with the EA3500 or even allow me to access the router through the default gateway IP. I've since put the WRT45GL back in place and I have access again with my EA2500 adapter. I should note that with the EA3500 in place, if I disconnected from my wireless I couldnt see any networks until I unplugged the adapter and reinserted it into the USB port (i've also tried many different ports). I've named the SSID's of the two routers differently, tried a manual setup of the wifi, tried the CD setup, the wifi protected setup, no security, and WPA2 to no avail. I can't seem to get the EA2500 adapter and the EA3500 router to get along. I'm running W7 x64 Pro.
View 6 Replies View RelatedI've recently purchases a Canon MF3010 Multifunction printer, and connected this to my EA3500 router's USB port. Used Cisco Connect to setup the printer, and the print function is working fine.
The issue is with the scan function. It appears the default functionality of the router is to only activate the connection to the printer when a print job is fired off. When this connection is active, the scan functionality works fine.
Another way to activate the connection to the printer to allow for scanning would be to go through
Cisco Connect>Computers and devices>PrinterWhile the process is running (searching for printer), the connection is active as well, and scanning works fine. When the process is closed, scanning no longer works, with an error message stating that communication to the printer cannot be established.
Is there a simpler way to keep the connection to the printer active, or some sort of configuration to automatically establish this connection for scanning?
I have an HP Veer Webos phone. Since I upgraded to an EA3500, I haven't been able to connect my phone to the network wirelessly. Today I temporarily installed a WAP54g on the network, and I am able to connect the Veer via the WAP. I spent 45 minutes chatting with Cisco Support today, but didn't resolve the problem. I believe I have the same situation with an HP Touchpad, but can't say the problems are identical, since its battery is down right now.
[code]....
Its not even listed as a download on the official page of the router. How can i see the notes?
View 9 Replies View Related