Linksys Wireless Router :: WRT100 - How To Disable Automatic DNS Name Service Configure
Dec 9, 2011
I have a WRT100 wireless router, which is configured for a PPPOE connection to my ISP. After running one of the tools to determine responsiveness of DNS name services, I would like to manually configure my DNS services, placing a more responsive service as my first DNS choice. In the router administration, I can configure three static DNS IP's. However, I don't see any place in the configuration to turn off the automatic DNS configuration from my ISP. So, when I issue an IPCONFIG /ALL on my computer, the DNS listing shows two DNS Name Services from my ISP ahead of the three static DNS IP's that I configured.
View 3 Replies
ADVERTISEMENT
Apr 17, 2012
I'm visiting at my aunt's house and her Linksys was not working properly, so I reset it to factory default, and it's working now, except now I cannot seem to find the how-to page on how to set up the WEP security again (or another security variation...whatever is appropriate now for a home-based router).
View 1 Replies
View Related
Feb 28, 2013
Does WRT100 model is compatible with Windows 8? Everytime I connect my laptop all the other devices drop their connection.
View 2 Replies
View Related
Aug 3, 2011
I had to restore my laptop yesterday and i reset my router (WRT100). I ran all the Microsoft updates, but I didn't do anything with the router other than going to the Linksys site to try to make it secure. My computer seems to be recognizing the router (although it is still saying it is an unsecured connection) but I cannot get on the internet. The problem seems to be when I pull up the Network Connections window the "Internet Gateway-Internet Connection" is showing disabled. I cannot enable.Everytime I try, it says "connecting...Connection failed!". I can plug the ethernet from the modem to the computer and it works and the "Internet Gateway" doesn't appear, but when I try through the router it does. I want to set up the router because I have two computers that need internet access.
Three connections are listed--Wireless Access, LAN, and 1394 Connection. All are listed as connected, firewalled.The second computer is also giving me a problem. There is the wireless issue, but when I connect the ethernet from the computer directly to the modem I am asked if I want to connect via Broadband and am asked for a username/password. There is no username/password. I've contacted my ISP (Cox cable) and confimred there is no password.
View 1 Replies
View Related
Nov 12, 2011
How to secure my router WRT 100 again...
View 4 Replies
View Related
May 15, 2012
im working in company that develop high speed networking equimpnet(Mellanox)we develop 4056GB network cards and switches.we have developer network on HP pro curve switchs, the engineering make tets on servers with the high speed network cards and sometimes the test "go out" from the 4056GB network cards and switches and "boombing" the regular network of 1G in hp swiches.i meen every server are connecting with RJ-45 cable for access to the server and the real work is on th Mellanox switches and network cards but sometimes the test "run away" to the ethernet network and 40G traffic are killing the network.function in HP switches that recognize over booking traffic and automatic disable the bombed port?now we have spening tree and brodcaste limit on every switch but its not enough, the big traffic kill the network until we disable the problematic port and igonre the bombing server.we have hp procurve 5610 layer3 switch and pro curve 2510 switches.
View 4 Replies
View Related
Oct 24, 2012
I recently got my hands on the latest Secure Mobility VPN v3.1.01 client. We are upgrading from the old anyconnect 2.4 client so there are many changes that are catching us by surprise. The biggest issue I have right now is that the new Mobility VPN launches automatically when a user signs into a machine. We would like to disable that automatic connection/launch feature. With the old 2.4 client we simply disabled the AnyConnect Service in Services.msc by default and started it up when a user was ready to connect.
View 5 Replies
View Related
Oct 10, 2012
we have a AP cisco AIR-AP1131G-E-K9 Version 12.4(10b)JA, and we would like to do automatic backup of CLI configuration to one server, and we dont know how to do.
For example: On router and switch we use this kind of configuration to do automatic backup: [code]
View 1 Replies
View Related
Aug 2, 2011
I have a WRT54GS wireless router. I can successfully set up the router with my DSL modem for PPPoE. Here's my problem. The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically. I DON'T want it to do that. Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?
View 1 Replies
View Related
Apr 18, 2010
I am working with a WRT320N for some weeks now, but I don't get the fact that 40Mhz channel width is only allowed for Automatic channel selection.I keep losing connection and the channel keeps changing.I want an option to change the channel manually (like in every good WLAN router!!), also with N data rate (40Mhz channel width).I know how to select the best channel, so why aren't I able to change it the way I like it?
View 4 Replies
View Related
Jan 27, 2013
I have to go back into settings and deactivate the IPV6 tunnel daily to keep access to youtube. My provider does not support IPV6. Saving changes has no effectIs there a way to ensure that the IPV6 tunnel remains deactivated?I have firmware version 1.0.30 build 126544 2011-12-24. Firmware update function says I got the latest version.
View 5 Replies
View Related
Nov 19, 2012
I am curious as what the packet size should be set . is the bigger size == lower speed smaller == faster or just leave automatic setting for packet size?
View 4 Replies
View Related
Mar 21, 2012
do external hard disks automatically spin down after a period with no access/use when connected with the USB port of the WRT160NL?
View 1 Replies
View Related
Dec 9, 2012
I am trying to determine the best way to setup my E4200 V2 so that it is “uplinked” correctly to a Comcast Dory Modem/router. Currently we have the E4200 V2 router plugged into the Comcast Dory Modem/Router using a CAT6 cable from one of the Ethernet ports on the Comcast device to the WAN port on the E4200. The E4200 is set to “Automatic Configuration - DHCP.”
We are trying to do two things. First better WIFI in the center of the house and for a TV located next to the Comcast device, and second, have all devices in this house see and access all other devices including the Samsung SmartTV, my son’s two systems upstairs, the 3 systems in the room with the E4200, and the one network printer. In the room with the E4200 we have 3 computers and one network printer. 3 of those 4 devices support WIFI so we don’t have to use all 4 Ethernet ports on the E4200.
I see others talking about running the CAT6 cable to an Ethernet port on the E4200 instead of the WAN port and setting it to “Bridge Mode.” Right now the system appears to be working fine although we are sometimes experiencing brief dropped connections with the devices hardwired into the E4200.
Should I be running the E4200 in “Bridge” mode or “Automatic DHCP” mode and which port on E4200 should the CAT6 from Comcast be plugged into?
View 9 Replies
View Related
Apr 20, 2012
I'm trying to configure a dhcp service on a router for some vlans.I would like to give the range 172.16.0.0 - 172.16.10.255 to vlan 10, 172.16.20.0 - 172.16.20.255 to vlan 20.for some reason it doesn't work?here's the config.
ip dhcp excluded-address 172.16.0.1
ip dhcp excluded-address 172.16.20.1
ip dhcp excluded-address 172.16.30.1
ip dhcp pool vlan10
network 172.16.0.0 255.255.0.0
[code]...
View 10 Replies
View Related
Feb 16, 2013
I have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
View 3 Replies
View Related
Apr 25, 2011
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies
View Related
Aug 20, 2011
Is there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
View 3 Replies
View Related
Apr 20, 2013
My network consists of a Westel C90-610030-06 DSL modem, Cisco E2500 router and Hawking HWREN100 range extender.My wife has trouble with her IPad connecting to the Hawking.Apple says I need to Disable WMM on the E2500.
View 2 Replies
View Related
Feb 3, 2010
Wireless service on Dell laptop computer had been running fine for 4.5 months until underground Comcast cable failed, presumably due to freezing and thawing in cold New England soil. All Comcast service went out, TV, Internet cable modem, etc. Service was restored with above ground cable, and wireless service returned to other devices in household, but not the Dell laptop. I am wondering if my wireless card itself was damaged in the event, as no software fixes I have tried have worked. However, the device manager says the Dell Wireless 1397 WLAN Mini-card is working properly and the driver software for the service is up to date.
Some of the messages I have received from various command line and dialogue box attempted fixes:
Dell Wireless 1515 Adapter Device Not Found
There are currently no wireless adapters available and enabled
Cannot repair adapter because wireless service is not running
Windows could not start the WLAN AutoConfig service on Local Computer
Error 0xc00 ce508 : 0x00 ce508
There might be a problem with one or more network adapters on this computer
When I did this
>Set Autoconfig Enabled=Yes Interface=”Wireless Network Adapter” <enter>
The response was this
>The Wireless Autoconfig Service (WLANSVC) is not running
When I was in administrator mode and ran SFC/SCANNOW the response was this Windows Resource Protection found corrupt files but was unable to fix some of them Details are included in the CBS.Log WindirLogsCBSCBS.Log For example C:WindowsLogsCBSCBS.Log Other command line responses:
Wireless LAN Adapter Wireless Network Connection:
Media State… Media disconnected
Tunnel adapter Local Area Connection* 6:
Media State… Media disconnected
Tunnel adapter Local Area Connection* 7:
[code]....
Other information about the computer:
Inspiron 1545, Dell BIOS version A10, BIOS date 7/17/09, running Microsoft Windows Vista Home Premium, Processor Pentium (R) Dual-Core CPM T4200@2.00 Ghz, Network Card Adapter Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller, Wireless 1515 WLAN Half mini card (Atheros).
View 1 Replies
View Related
Jul 20, 2011
I have an E2500 and i need to disable the ports on the router. I have a DSL line going in and thats it. I do not want it to be able to accept any wired device and have someone get on the internet. I do not want someone to just take a laptop, with a LAN able, plug it into a port, and get internet. How would i be able to disable the ports?
View 9 Replies
View Related
Oct 8, 2009
How do I disable the wireless?
View 9 Replies
View Related
Oct 10, 2012
I think I've been carefully through every single screen and can't figure out how to disable the wireless broadcast on my new EA6500. I typically see this in the "wireless" settings but must be missing something.
View 4 Replies
View Related
Dec 13, 2012
Where will I find the firmware? The Support site gives none for the E1200.
View 9 Replies
View Related
Nov 19, 2012
I am trying to use my EA4200 wireless as simply a router to run my home network. I want to leave all my cables plugged into it and distribute the internet via the switch to my other computers. I just want to turn of the wireless feature.
View 2 Replies
View Related
Mar 14, 2007
WRT54G v7 - cannot specify service provider
View 9 Replies
View Related
Nov 18, 2011
Just bought an E1500 wireless router -- when setting the router name and password, a 2nd guest sight came up, but I had to leave the computer, and when I came back that page was not there. I do have a guess password, that is fine---what I want to remove is the guest signal to our Dish Network wireless sight.
View 2 Replies
View Related
Nov 21, 2012
How can you disable SSID broadcast on EA6500 wireless network.
View 4 Replies
View Related
Jul 28, 2011
How do I disable the broadcast of my SSID? I do not want wireless. I only bought this router to hook up two computers to the internet via Ethernet cable.
View 9 Replies
View Related
Feb 7, 2013
How do I disable ICMP echo on ea4500 - I don't see anywhere either in Connect or directly on the router web interface that allows this.
View 1 Replies
View Related
Nov 8, 2012
Can the broadcast be disabled on EA6500?
View 1 Replies
View Related
Oct 10, 2011
I want to disable the guest access connection on E1000 wireless router but this option is not in the firmware menu. So, now I read that I need to use Cisco Connect on the CD to change this feature. When I run the Cisco Connect software, it says it can't configure the router (probably because I already have it configured). Why doesn't the Cisco Connect software simply take me to the settings where I can change the guest access feature? Why does it try to re-configure the router? Whoever designed this at Cisco was probably smokin some medical MJ because it doesn't make any sense that I have to go through so many hoops to do something so simple.
View 8 Replies
View Related
Jan 14, 2013
So I've realized that my parental controls were being ignored by the computers, at first I figured my son had found a work around to by-pass. But reading through the forums today, I've found that IPv6 being enabled might be the cause of my issue. So I'm currently sitting at work and connected to my router remotely, but for the life of me, can't see where to disable this option. Using the Smart Wi-Fi interface, closest I can get is "Connectivity, Internet Settings, IPv6 but everything is grayed out and no option to edit this.
View 9 Replies
View Related
