Linksys Wireless Router :: WRT100 - Internet Gateway Connection Disabled
Aug 3, 2011
I had to restore my laptop yesterday and i reset my router (WRT100). I ran all the Microsoft updates, but I didn't do anything with the router other than going to the Linksys site to try to make it secure. My computer seems to be recognizing the router (although it is still saying it is an unsecured connection) but I cannot get on the internet. The problem seems to be when I pull up the Network Connections window the "Internet Gateway-Internet Connection" is showing disabled. I cannot enable.Everytime I try, it says "connecting...Connection failed!". I can plug the ethernet from the modem to the computer and it works and the "Internet Gateway" doesn't appear, but when I try through the router it does. I want to set up the router because I have two computers that need internet access.
Three connections are listed--Wireless Access, LAN, and 1394 Connection. All are listed as connected, firewalled.The second computer is also giving me a problem. There is the wireless issue, but when I connect the ethernet from the computer directly to the modem I am asked if I want to connect via Broadband and am asked for a username/password. There is no username/password. I've contacted my ISP (Cox cable) and confimred there is no password.
I have a desktop computer that I have used for years and it has always worked just fine. We have AT&T (DSL, not cable) and it used to connect just fine but then I moved out, left everything plugged in exactly as it was and when I came back it wouldn't connect.It connects to the LAN but not to the internet. When I go in cmd to type ipconfig the DNS suffix is blank on that computer but says gateway.2wire.net on my wireless laptop. I eventually disabled UPnP on it because that's what alot of people were saying fixed the problem but it didn't fix anything. All it did was make the Internet Gateway Connection box disappear.Originally it was plugged in like so: Cable from wall > Cable Box > PC Now it is hooked up like this: Data cable from wall > DSL > Router > PC It stopped working BEFORE it was switched to DSL so that isn't the problem The DSL we have is "AT&T 2701HG-B 2Wire Wireless Gateway DSL Router Modem" and the Router it is plugged into that goes to my PC is a Linksys Wireless Router Model WRT54GS The PC is Windows XP Home, SP2?
I'm visiting at my aunt's house and her Linksys was not working properly, so I reset it to factory default, and it's working now, except now I cannot seem to find the how-to page on how to set up the WEP security again (or another security variation...whatever is appropriate now for a home-based router).
I have a WRT100 wireless router, which is configured for a PPPOE connection to my ISP. After running one of the tools to determine responsiveness of DNS name services, I would like to manually configure my DNS services, placing a more responsive service as my first DNS choice. In the router administration, I can configure three static DNS IP's. However, I don't see any place in the configuration to turn off the automatic DNS configuration from my ISP. So, when I issue an IPCONFIG /ALL on my computer, the DNS listing shows two DNS Name Services from my ISP ahead of the three static DNS IP's that I configured.
The update "failed," due to an "unexpected error." Wireless connection is disabled, although, as you have probably noticed, I can still connect to the internet (using an ethernet cable from my router to my laptop OSX 10.6.8). Error Code 3018 is unknown to Cisco's website. Or should I just start over with the installation disk for my E4200 router?
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all Cisco SG 300-20 (switch) 192.168.89.3 all Clients(15 x DHCP assigned IPs) connected to switch WRT300N(192.168.89.2) connected to switch Internet modem connected to WRT300N
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).
I cannot connect to the internet on my laptop using wireless. It was working fine for a while and it just stopped. This is not the first time this has happened. Although i cannot remember if i caused it to start working again. My laptop wireless hardware has disabled itself. I've tried enabling/disabling and troubleshooting from what i know how to do but its still not working. This problem started yesterday.
Tech Support Guy System Info Utility version 1.0.0.1 OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit Processor: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, Intel64 Family 6 Model
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
Iam unable to share my internet connection.I am unable to use it on a router even.When i connect it to my laptops Ethernet port its working fine.But when i connect it via router its just showing internet access but i m unable to open any pages.
I have a win 7 netbook that I recently got and for some reason it suddenly cannot keep a connection to the internet. It used to keep a connection before but now I keep getting the error the default gateway is not available about every ten minutes while connected which of course is very frustrating.
I've tried updating all associated drivers but apparently that hasn't changed anything. I've tried restarting the computer and tried different connections. I know its nothing to do with the internet connection I'm trying to connect to as other devices are able to keep a connection with no issue.
Linksys has disabled my wireless adaptor for wireless devices such as my Netflix streaming movie player. They are asking for my routers user name and password which I am not accessing right, I get "401 Authorization required" How do I factory restore my router? It's a D-Link DES-1105 router model BEFW1154V4. I need to enable my network for wireless connection. How to get my routers user name and password? I 've had my Netflix player hooked up and working for almost a year and have never encountered this problem. Im going to purchase a linksys wireless adaptor the first of the month with having a secure connection to linksys instead of having to wait all day for wireless linksys with the Ativa adaptor I already have?
I have a cisco e1000 route. i've already set up wireless network successfully with cisco connect software. However, when i logged in web-based config, i disabled NAT with the routing table is unchanged. the problem is anyone from the network to which the Internet WAN port links can ping and receive reply from PCs inside the wireless network but it's impossible for the reverse direction and any traffic from the inside of e1000 can't be passed through.
Trying to secure Linksys WRT54G V8 wireless router. Can't change security mode from 'Disabled'!?
I followed this Post from EXPERT: "Connecting two routers wired - the definitive answer"
[url]...
I got the two routers working but the second one (not using it as a router) is not allowing me to change security mode from "disable" to WEP or anything else.The following Post didn't answered this issue: "Can't change wireless Security Mode on my WRT54G V5"
I call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Action tech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router.
I just purchased an e4200 in a corporate environment where we already have a wireless router. I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless). I set the Linksys to bridge mode and assigned it an ip address. I disabled all wireless settings, etc. I then connected the internet port of the Linksys into a data port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this.
why my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
This problem is on a Cisco E1200 (FW: 1.0.03) and using a browser to modify the routers settings.I'm connected to the router from a wired connection, and I'm trying to turn off the encryption, and just have the router have the setting "disabled" as the selection for "Wireless Security".
However, it seems when I do this, the moment I press "Save" the router gets disconnected from my computer (the wired connection) and the only way to get reconnected is to run the Cisco Connect software from the computer that's hard wired to the router.
Once I get back to that screen in the routers settings, and try it again, the same thing happens.If I change anything else under the routers settings, the connection stays connected, but only when I change the wireless security settings to disabled I see this problem.
I have a Nat Strict problem with my router model WRT160N. I want to make a dedicated server with UT3.I tried many things like disabled all security in the router or disable UPNP, fowarding every ports that Unreal Tournament need or DMZ settings. I am running a batch file to start the dedicated server... but still have '' Nat is now strict'' in the log of my batch file. I cant see my server in the master server list inside the UT3 game. I tried to make the server without my router, directly connected to the modem and then it works instantly.
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings: IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
- I have tried to reset the router both by holding the reset button and through the configuration application. - I have enabled and disabled wireless to see if that was slowing things down - I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500) - I tried putting the computer in the DMZ - I have changed the ports that the computer is plugged into - I have disabled and enabled IPV6 on both router and network card - Firmware version - 1.1.38.134141
I can browse web pages and such, but i can't watch any videos or download bigger files. The videos usually play for about 4 seconds and files download about 3 MB before it just loads forever. I go to control panel and look at the network connections, and while the LAN is connected, the internet gateway just says "connecting".
im having a problem with my 2701hgv -e. I connected it to my laptop and I tried to enter the settings of the router but was unable to do so. but when I ran the ipconfig command, there was no default gateway. I tried to press the reset button but nothing happened.
Anyway, a neighbour is letting us share their broadband by way of a wifi connection (on a very long USB lead into the front garden...) but this only works on one PC.The PC is right next to the Orange router (Brightbox) but so far I've failed to do anything like bridge the connections from wifi to ethernet to the router and beyond. Should I persevere with this? I don't understand how this would work in terms of DHCP and routing IP traffic.I'm prepared to buy new kit if necessary (but not much). Most of my equipment is wifi enabled but due to the signal strength of my neighbour's wifi you have to be on the front lawn to get a signal.
I have a router (Linksys E3500) set up as an AP. To do that I just disabled DHCP on the router. I can connect devices to it fine, but I'm having a couple of issues.
So I have a DC setup. It's in the same subnet as the router and I can ping it fine, but when I browse to the AP for management it prompts with the username/password and won't accept the credentials. Not sure what's going on here as I've always used the same credentials and I logged into the router fine when I was first setting it up.
Another issue, is if I try to ping this router from a different subnet, it fails. I can ping the DC fine from this subnet. Would this be to do with the AP just acting as a pass-through?
