Linksys Wireless Router :: Disabled DHCP And Configured E1200

Jun 4, 2012

I call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Action tech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router.

View 5 Replies


ADVERTISEMENT

Linksys Wireless Router :: E1200 Setting Disabled As Selection For Security

Apr 1, 2012

This problem is on a Cisco E1200 (FW: 1.0.03) and using a browser to modify the routers settings.I'm connected to the router from a wired connection, and I'm trying to turn off the encryption, and just have the router have the setting "disabled" as the selection for "Wireless Security".
 
However, it seems when I do this, the moment I press "Save" the router gets disconnected from my computer (the wired connection) and the only way to get reconnected is to run the Cisco Connect software from the computer that's hard wired to the router.
 
Once I get back to that screen in the routers settings, and try it again, the same thing happens.If I change anything else under the routers settings, the connection stays connected, but only when I change the wireless security settings to disabled I see this problem.

View 1 Replies View Related

Linksys Wireless Router :: WRT300N Not Providing Internet When DHCP Disabled

Apr 5, 2012

Here is where I want to go:
 
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
 
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).

View 6 Replies View Related

Linksys Wireless Router :: DHCP Reservations On E1200?

Feb 8, 2012

I'm setting up a new E1200 and I'm searching for the area for DHCP reservations. My D-Link DIR-615 offers this ability in the Admin panel. This is quite useful since it allows for easier port forwarding management to specific Machine IPs without having to assign static IPs for each machine. I can't seem to find any documentation on this feature no the site or in the forum that applies to the E1200. If it's not offered, boy did I make a mistake in getting the E1200. I should have bought another DIR-615.

View 2 Replies View Related

Linksys Wireless Router :: E1200 Bridge And Have Wi-Fi DHCP?

Oct 25, 2012

At my work we have Comcast Business Class, and our LAN uses the Comcast's SMC static 10'net addressing.  Our two POS computers are connected to wall ports that connect to the SMC router (unsure its model number, it's screwed to the wall).  There is only 1 LAN port for each POS computer, I am trying to setup a 3rd computer up by the POS stations for dedicated web searching of products, emails between HQ and the other stores. 
 
Like I said our LAN is using the 10'net addressing, and only a single port I can use.  I would like to use the E1200 as a bridge/switch to connect: POS computer, network label printer. and network printer/copier/scanner/FAX .. and also have wifi available.  The POS & printers need to have their static 10'net IPs .. but I want the wifi to use DHCP from the E1200.

View 9 Replies View Related

Linksys E3500 Disabled DHCP On Router

Aug 5, 2012

I have a router (Linksys E3500) set up as an AP. To do that I just disabled DHCP on the router. I can connect devices to it fine, but I'm having a couple of issues.

So I have a DC setup. It's in the same subnet as the router and I can ping it fine, but when I browse to the AP for management it prompts with the username/password and won't accept the credentials. Not sure what's going on here as I've always used the same credentials and I logged into the router fine when I was first setting it up.

Another issue, is if I try to ping this router from a different subnet, it fails. I can ping the DC fine from this subnet. Would this be to do with the AP just acting as a pass-through?

View 1 Replies View Related

Linksys Wireless Router :: E1200 DHCP Systems Loose Ability To See Other Network Computers

Nov 22, 2012

Have Win7 and XP systems in my network wire connected to the router. When IP of both systems are not reserved, each computer can see other network computers and devices, five in total.A good thing that both systems get each time same IPs which even got not changed since I upgraded from E1200.When I reserve an IP for each system exactly that they currently have, both systems loose ability to see other network computers. Network shares not affected, I still can remotely access my XP box remotely from my 7 via RDP by computer name. WDTV Live wirelessly connected to the router can get/update its IP address (no connection issues) but same as others cannot see network resources.

Tried different ways, rebooted, finally ended up with device reset pushing the button.The next day I managed to reproduce the issue, but was able to revert by disabling/enabling of DHCP server.Another issue I got with an external HD connected to the router when some files got converted to folders by uTorrent started from that drive.I had to use Unlocker application to be able to delete folders converted. I can just assume that issue because of anonymous access was enabled to the external disk. No problems when same HD connected to PC USB.

View 9 Replies View Related

Modem To Gigabit Switch To E1200 Wireless Router For DHCP?

Oct 4, 2012

The first part, is this even possible? Modem to switch.

Second part, e1200 router plugged into switch, handles DHCP for the switch.

Plug gigabit computers into the switch, non gigabit/wireless devices into the e1200 router.

If e1200 can't handle DHCP for the switch, could I configure a DHCP linux server directly to the switch?

I don't want to limit my network to my e1200 speeds when I have a gigabit capable modem and a gigabit capable switch.

View 1 Replies View Related

Cisco Switching/Routing :: Router Is Connected To Switch 2960 Configured As DHCP SNOOPING

Sep 3, 2012

We have a DHCP SERVER implemented in a cisco router 2610.This router is connected to a switch cisco 2960 configured as DHCP SNOOPING. At the switch appear the next log message: [code] The ip address: 10.100.200.1 belongs to DHCP SERVER configured at router cisco 2610. What to do so these log messages does not appear any more? Do I need to do some configuration changes at some switch or router?

View 11 Replies View Related

Linksys Wireless Router :: Cannot Access Already Configured WRT54GL?

Jul 3, 2012

We have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
 
But, we are unable to connect to this box,by SSH or  by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
 
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G2 Not Configured To Allow GRE Protocol

Mar 24, 2012

I have a WRT54G2 with the most recent firmware upgrade (which brings issue one - there hasn't been a firmware upgrade released since mid 2009?) and am trying to connect to a VPN for work.  The connection fails and I have gotten error messages indicating the issue is the router is not configured to allow GRE protocol. 

View 1 Replies View Related

Linksys Wireless Router :: Wrt160nv3 / Port Forwarding Is Not Configured

Jun 18, 2012

I just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.

View 9 Replies View Related

Linksys Wireless Router :: Configured Port Forwarding On E4200

Oct 16, 2012

I have a Cisco E4200 with a Thecus NAS behind it. I configured port forwarding on port 80, 1080 and 4433 to access the NAS. However it's not working. Also tried to place the NAS in DMZ, but also I cannot connect it from outside my network. Inside my network, there is no problem.I also connected the NAS directly to the internet, and then I can access it from outside my network.I already tried a factory reset, disabled UPnP and IPv6, but nothing seems to work. I also replaced the router with a Cisco E3200, but it makes no difference.

View 9 Replies View Related

Linksys Wireless Router :: BEFW1154V4 Disabled Adapter For Devices

Jun 27, 2012

Linksys has disabled my wireless adaptor for wireless devices such as my Netflix streaming movie player. They are asking for my routers user name and password which I am not accessing right, I get "401 Authorization required"  How do I factory restore my router? It's a  D-Link DES-1105 router model BEFW1154V4. I need to enable my network for wireless connection. How to get my routers user name and password? I 've had my Netflix player hooked up and working for almost a year and have never encountered this problem. Im going to purchase a linksys wireless adaptor the first of the month with having a secure connection to linksys instead of having to wait all day for wireless linksys with the Ativa adaptor I already have? 

View 2 Replies View Related

Linksys Wireless Router :: Cisco E1000 Can't Route When NAT Disabled

Sep 11, 2011

I have a cisco e1000 route. i've already set up wireless network successfully with cisco connect software. However, when i logged in web-based config, i disabled NAT with the routing table is unchanged. the problem is anyone from the network to which the Internet WAN port links can ping and receive reply from PCs inside the wireless network but it's impossible for the reverse direction and any traffic from the inside of e1000 can't be passed through.

View 6 Replies View Related

Linksys Wireless Router :: Can't Change Security Mode From Disabled

Aug 30, 2012

Trying to secure Linksys WRT54G V8 wireless router. Can't change security mode from 'Disabled'!?

I followed this Post from EXPERT: "Connecting two routers wired - the definitive answer"
 
[url]...
 
I got the two routers working but the second one (not using it as a router) is not allowing me to change security mode from "disable" to WEP or anything else.The following Post didn't answered this issue: "Can't change wireless Security Mode on my WRT54G V5"

View 8 Replies View Related

Linksys Wireless Router :: E4200 Disabled All Wifi Settings

Jul 16, 2012

I just purchased an e4200 in a corporate environment where we already have a wireless router.  I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless).  I set the Linksys to bridge mode and assigned it an ip address.  I disabled all wireless settings, etc.  I then connected the internet port of the Linksys into a data  port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this. 

View 3 Replies View Related

Determine IP Address Even DHCP Disabled

May 18, 2011

problem is my brother has been playing with its config page. he changed the IP Address of the modem and disabled DHCP. he forgot what IP Address he inputted on the config page. I tried resetting the router with the small button on its side. Nothing happens. all the lights blink when i pushed the reset button for 10 sec. but nothing happens. i still can't access its default IP which is 192.168.1.1 IS there anyway to determine its IP Address even if DHCP is disabled ?

View 5 Replies View Related

Cisco :: LMS 4.0 Disabled DHCP Client

Jan 23, 2012

I have a fresh install of LMS 4.0 on Windows Server 2008 Standart SP2. I have one NIC with static IP configuration. I also disabled DHCP client.The problem is follows: when I go to Inventory - Device Administration - Add/Import/Manage Devices, I always get this error:Error in communicating with DCR Server. DCR Server may be down. Please start the DCR Server and then refresh the page.Reload server/ Daemon Manager dont solve this.I try to beat this problem 2 days already. Second uninstall also doesnt solve the problem..
 
About a week ago I tried to clear log files which was 270gb (syslog.log) and after that restarted the server. And all inventory devices suddenly disappear! I could find it from search menu but cant access - cisco works said that there is no such a device in Device Repository or I havent enough right to view it (but i logged as admin). And after this i failed to add any device in Inventory. So I reinstall Cisco Works and get that DCR error..

View 1 Replies View Related

Linksys Wireless Router :: WRT100 - Internet Gateway Connection Disabled

Aug 3, 2011

I had to restore my laptop yesterday and i reset my router (WRT100).  I ran all the Microsoft updates, but I didn't do anything with the router other than going to the Linksys site to try to make it secure.  My computer seems to be recognizing the router (although it is still saying it is an unsecured connection) but I cannot get on the internet.  The problem seems to be when I pull up the Network Connections window the "Internet Gateway-Internet Connection" is showing disabled.  I cannot enable.Everytime I try, it says "connecting...Connection failed!".  I can plug the ethernet from the modem to the computer and it works and the "Internet Gateway" doesn't appear, but when I try through the router it does.  I want to set up the router because I have two computers that need internet access.  
 
Three connections are listed--Wireless Access, LAN, and 1394  Connection.  All are listed as connected, firewalled.The second computer is also giving me a problem.  There is the wireless issue, but when I connect the ethernet from the computer directly to the modem I am asked if I want to connect via Broadband and am asked for a username/password. There is no username/password.  I've contacted my ISP (Cox cable) and confimred there is no password.

View 1 Replies View Related

Linksys Wireless Router :: E2500 SSID Broadcast Disabled But Still Shows Up

Dec 1, 2011

why my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations.  The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it.  I have the router configured to only allow certain MAC addresses wireless access as well.  Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network. 

View 4 Replies View Related

Linksys Wireless Router :: WRT160N Disabled All Security Or Disable UPNP

May 30, 2011

I have a Nat Strict problem with my router model WRT160N. I want to make a dedicated server with UT3.I tried many things like disabled all security in the router or disable UPNP, fowarding every ports that Unreal Tournament need or DMZ settings. I am running a batch file to start the dedicated server... but still have '' Nat is now strict'' in the log of my batch file. I cant see my server in the master server list inside the UT3 game. I tried to make the server without my router, directly connected to the modem and then it works instantly.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Updating Get Failed / Wifi Connection Is Disabled

Jul 14, 2012

The update "failed," due to an "unexpected error."  Wireless connection is disabled, although, as you have probably noticed, I can still connect to the internet (using an ethernet cable from my router to my laptop OSX 10.6.8).  Error Code 3018 is unknown to Cisco's website. Or should I just start over with the installation disk for my E4200 router?

View 2 Replies View Related

Linksys Wireless Router :: EA3500 Disabled And Enabled IPV6 On Network Card

Apr 9, 2013

I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
 
- I have tried to reset the router both by holding the reset button and through the configuration application.
- I have enabled and disabled wireless to see if that was slowing things down
- I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500)
- I tried putting the computer in the DMZ
- I have changed the ports that the computer is plugged into
- I have disabled and enabled IPV6 on both router and network card
- Firmware version - 1.1.38.134141

View 9 Replies View Related

Routers / Switches :: Why Do DHCP For DLINK DSL-2540T Always Keep Disabled

Jan 5, 2011

why do my DHCP for DLINK DSL-2540T always keep disabled although i already set for enabled one day before?

View 1 Replies View Related

Linksys Wireless Router :: How To Get Best Speeds Possible For E1200

Dec 22, 2012

I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them. 

View 9 Replies View Related

Linksys Wireless Router :: E1200 - Cannot Open NAT?

Jun 5, 2012

I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!

View 7 Replies View Related

Linksys Wireless Router :: E1200 Won't Connect With Key?

Aug 12, 2012

Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password). 

View 9 Replies View Related

Linksys Wireless Router :: Connection From Outside To E1200?

May 1, 2013

I purchased E1200 and have a problem. I  have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.

View 4 Replies View Related

Linksys Wireless Router :: E1200 - Cannot Get It To Connect To TV

Nov 7, 2011

I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet.  I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well.  I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player.  When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV.  CANNOT establish an internet connection?

View 2 Replies View Related

Linksys Wireless Router :: Possible To Use E1200 As Repeater

Jan 4, 2012

Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?

View 3 Replies View Related

Linksys Wireless Router :: E1200 - Set It Up With Tablet?

Oct 23, 2012

Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.

View 1 Replies View Related

Linksys Wireless Router :: Can't See Where To Set A User Name On E1200

Dec 29, 2011

I can't see where to set a user name on my E1200. I set a password for the web interface then it boots me out and I am promted for the password and username.I don't want to download and configure my router with some poorly written software for my mac;  why can't I just do it all through the good old web interface???? I'm able to set everything else up fine but when i set the password I am basically rendering the web interface usless and have to reset the router!! (running Lion, latest build with 8gigs of ram and N wirless adaptor in lappy) 
 
Ok, so I was given this router for free so I shouldn't complain but I do not see any speed increase over my 6 year old 54G rinning wrt, perhaps I need summin better than this $50 walmart special Getting about 10mps download which is also the theoretical max of G right) 

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved