I have a small call center and we are struggling with adequate dsl bandwidth for our voip. The providers cannot give us more upload bandwidth. Any way to combine the bandwidth of two or more lines so that the server/switch sees increased bandwidth for upload?
View 1 RepliesI'm going to combine 2 512 kbps ADSL line in my PC. i know that it would be much better to get a 1 MB ADSL connection...but the problem is where i live now there is not better speed than this! Well i have a PC with 2 LANs - 2 phone lines - 2 ADSL modems - as far as i learned from Google , by no means it is possible to combine them to have 1 MB data rate but it is possible for example IDM would works with one 512 and another program with another 512..!! And load balancing is the only solution for this which it needs a special routers ! it is somehow difficult for me to provide one ..!! so my question is :
1- Is there any other solution for combining this 2 lines?! I heard something about teaming.
2- Is it possible to use load balancing by software?
3- How about the efficiency and ping time?
I have cisco 1841 router and two types of ISP line (Different provider):
1. Lease line = 2 mbps ( it is terminated over cisco 1841 router); For internet-access purpose
2. DSL = 1 mbps; For internet-access purpose
Our cisco 1841 router have only two fastethernet port, first for WAN Port where 2 mbps lease line terminated , second for LAN which is connected to Cisco switch and 1 mbps adsl line running seperatly which is not part of cisco 1841 router. i am planning to buy HWIC card for extra wan port on existing router where i will terminate 1 mbps adsl line or may be other provider lease line.I want to merge or aggregate both WAN link, My concern is to merge both line (2+1) and get single one (Just like as Etherchannel thing) , get 3mbps for LAN for internet access.
I'm currently in the process of doing a bandwidth analysis on 2 WAN links at my current HQ / remote sites. The topology is pretty straightforward, two 3845 routers at HQ, and two 3845 routers at my remote site, both with P2P DS3 interfaces between them. From each router we then connect directly into a 6509 at the HQ, and a 4506 at my remote site where we are using equal cost load sharing (EIGRP) to split the load / give us redundancy between the sites.
I'm just looking for a good test for how well the circuits are performing. I've done some basic file transfer tests, but they're only showing about 4MBPS, which seems quite slow. I also know that this isn't a true measurement because there are amny different factors involved, like hard drive write speeds, network congestion, etc, that may influence the test.
I want a solution which should be 2 WAN convert in to 1 WAN.
View 1 Replies View RelatedI am using 2 internet data card and would like to merge them to have high speed. I am using XP and Window 7
View 1 Replies View RelatedWhat I want to do is combine a sad 1.5M DSL connection and a long range WiFi signal into a single connection for a rural area home.I am looking for any effective solution (including boosting WiFi output signal beyond FFC suggested values). The WiFi long range antenna (DISH + gutted LNB) receives a full bar 40+ Mbps signal from 11 miles away. DSL is standard 1.5M over DSL Modem.
View 2 Replies View RelatedI have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt.As u know the connections work separately by default!! (I use Windows 7 64bit)Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 2 Replies View RelatedI have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt. As u know the connections work separately by default!! (I use Windows 7 64bit) Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 3 Replies View RelatedMy apartment complex limits each connection to 200KBps but each connection has the same IP so I thought there has to be an easy way to combine the connections. Is there a way to connect the wired network i'm connected to with the wireless one?
View 3 Replies View RelatedI am a day trader using Microsoft 7.I need to combine cable (comcast) and a wireless connection (AT&T) as backup into one access point.
View 1 Replies View Relatedsetting up a simple internet plan for a place, but a LAN center needs crazy fast internet, faster than most large enterprise class offices that take up an entire floor or two. Otherwise there is too much lag in games like first person shooters. We are expecting to have 60 computers, plus people bringing their own gaming rigs from home and laptops as well, xbox, ps3 and other consoles, all accessing the internet at the same time to varying degrees, with no room for lag. There is a LAN center in california that has 200 or more computers and they pay for 9 t3 lines, which is thousands and thousands of dollars per month. Plus the initial equipment to set that up from what I can find on cdw is many thousands of dollars also. Something like 10,000 for a router with 4 expansion bays, and 4000-6000 dollars for a t3 expansion card, bringing the total to around 22-28,000 for equipment to do just 4 t3's. Plus the monthly cost. Since we don't need all of the traffic to be secured like a high end business class line like a t3, I was considering what it would be like, and how one would set up, having multiple cable internet lines coming in. They make cable wic cards for cisco routers. 4, 50meg cable lines would give us 200 down and 40 up but I don't know how to make that work without having multiple public ip's. I was thinking that if I did have multiple public ip's on the network I could just divide the computers up so that they are in groups, using all of the public ip addresses for gateways, so that the load is split pretty evenly, but still, there should be a more seamless way to do this, I just don't know what it is. At the rate for business cable internet, 4 lines would probably only cost around 700 dollars a month, which is much better than probably 5 grand a month for several t3 lines.
View 3 Replies View RelatedI just installed a new RV016, and have it up and running currently using just one WAN (cable) on the Internet2 port. Just FYI I do plan to have a second WAN on Internet1 (DSL) once I get this next step working and want that to be the dafault provider, hence the use of Internet2 for this first connection.I already have a WRVS4400N installed that has a whole network on it that will be independant to the new the network and am trying to connect the WRVS4400N to my RV016. It is currently plugged into port 8 of the RV016 and the port is currently set to VLAN2.I know just enough to be a danger to myself here. :-) The RV016 is using the default IP of 192.168.1.1 while the WRVS4400N uses 192.168.10.1.I do know that "Typically, a Cisco RV0xx Series router is used as an access router, with a single LAN subnet. By default, the firewall is pre-configured to deny LAN access if the source IP address is on a different subnet than the router’s LAN IP address. However, you can enable multiple subnets to allow this router to work as an edge device that provides Internet connectivity to different subnets in your LAN."Hence I have added added the 192.168.10.1 subnet with mask 255.255.255.0 (to the RV016) and have tried switching the WRVS4400N from Gateway mode to Router mode. The RV016 can see it but nothing on the WRVS4400N network has any internet access, while computers on RV016 do. I assume this is because of the firewall blocking the traffic.
View 3 Replies View RelatedI'm trying to combine dynamic and static NAT on a SR520. My dynamic NAT is specified with:ip nat inside source list 1 interface Dialer0 overload access-list 1 permit 192.168.0.0 0.0.7.255 In addition to this I want to perform static NAT for a couple of selected internal hosts. I can do this:ip nat inside source static 192.168.1.5 10.85.10.2 which works fine but means that the source address 192.168.1.5 is translated to 10.85.10.2 for all destination IPs. What I want is for the above static translation only to occur for a particular destination subnet.To accomplish this I have tried:
ip nat inside source static 192.168.1.5 10.85.10.2 route-map toOtherSite
route-map toOtherSite permit 10
match ip address 150
access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
But this does not appear to work. Instead it seems to render the host 192.168.1.5 unable to progress through the NAT, whether the destination subnet is 192.168.10.0/24 or not, and I can't work out what I'm doing wrong.
I have D-link DSL 2750U wireless router. My PC and notebook are connected to router by Wi-Fi. They can share files or ping each other. I have a network storage unit plugged into router by an ethernet cable. Any of the computers cannot reach that storage unit or ping it. I guess my router isolates LAN network from WLAN network. Is there a way to combine them and get the router treat all devices connected to router in a single network?
View 1 Replies View RelatedI am having issues trying to combine two modules into one VDC. The modules are as mentioned below: When I try to combine module 1 & 10 as shown above, the nexus 7000 switch displays 'Not compatible'. I've read the online guide and it mentions that the F2 and M1 module cannot be combine into the same VDC. Problem is, my customer has already purchased the module, how do i solve this problem? If I separate the VDC, how does module 1 talk to module 10 if user wants to send traffic to Internet or Server Farm?
View 3 Replies View RelatedI have a DCP 3925 with 2 telephone and 4 internet ports.So, how can I combine DPC 3925 + E3000 to have more internet ports? and wich one is the best wifi than I can use ??Main router is the DPC 3925, where the internet is connected.
View 9 Replies View RelatedI play an online game, and latency is critical. I usually play at one server, and typically I get around 100ms ping. Today, when I joined the server I noticed my ping is now 40-45ms. My IP has not changed, internet service has not changed, service of server has not changed. It's almost as if the latency *just got better*. I know there are probably a huge number of factors regarding this, but I'm wondering how I could investigate this. Preferably, I'd like to keep my latency at 40ms, but I have no idea how it got there.
View 1 Replies View RelatedMy dad uses 2 modems, somehow they connect the whole house to the internet wireless. We all use laptops and 2 xboxs' but sometimes the connection will dip, not often but sometimes. Do you think this is my wireless adapter in my laptop or because of the use of modems to open up a wireless network?I was thinking about buying a router and just connecting it to the modem to maybe improve the connection. Suggestions? I really do not know the configuration my dad did for this network, the only thing I know is he uses modems not routers which is pretty strange.
View 1 Replies View RelatedBasically we have recently upgraded to a 100M connection but are having issues with the bandwidth we receive. Normally I'd blame the ISP and complain at them till something happens but there are some weird things.Basically one guy consistently receives 50M according to internet speed tests, while the rest of us have never measured above 10M. It should be noted that he is on a Mac and the rest of us are PCs.Having retested repeatedly at different times of day, wired and wireless.My network settings says that my LAN connection is 100M but my internet claims to never even reach a fraction of this. Are there any obvious ways to improve my connectivity?
View 14 Replies View RelatedIn my company i got about 50 computers all are in workgroup connected with ASUS Switch. Is there any way to findout on which ip got virus and how do i inrease total network speed .
View 1 Replies View RelatedI have a cisco851 and is currently configured this way.
1 .- This well configured?
2 .- the internet encourages me a little as I can improve
3. - how I can improve the performance
Today I was playing the ps3 (call of duty MW3)... normally I would connect via wireless but I'm getting a ton of lag and it's becoming frustrating. Later on I moved the ps3 downstairs and connected it via Ethernet and it worked so good.I want to look into buying those Ethernet power lines but not sure how good they are compared to running a Ethernet cable from the ps3 to the router or how good they will be vs wireless? I just don't want to waste money on these. If all else fails we will probs run a Ethernet cable through the ceiling
View 1 Replies View RelatedYou are responsible for managing and configuring printers and print servers for your organization. You must determine what you can do to increase the performance of your print servers responding to client print requests. What options are likely to improve print server performance?
View 4 Replies View RelatedI'm currently uploading FIVE videos on YouTube so that might be why. It says for a 30 minute long video its going to take 156 minutes.
View 4 Replies View RelatedMy pings, connected wirelessly.My pings, connected with an ethernet cable to the same router only a moment later, no difference in what programs are open and using the connection.This is a newer laptop model from Asus, specifically this one. Windows has been updated and the computer is otherwise well-maintained, I being a (usually) proficient pc user.This is on a friend's wireless network, not my own. I won't have access to my own until tomorrow but, anecdotally, I believe the symptoms are similar but a little worse here. Concerning his network, I have been sitting in the same room with two other people connected wirelessly as well to the same network for hours on end and they experience zero noticeable spikes.I've been trying to find a solution using google with no progress.
View 2 Replies View RelatedThe people i play with always tell me that Im lagging during Call Of Duty Black Ops. I feel like I just never get the first shot off.
Is there anyway that I can improve the connection to my ps3?
I want to use two seperate ISP's internet connection in single nic card. How to do this?
One ip is 203.76.112.106
subnet 255.255.255.248
gate way 203.76.112.106
DNs 1 203.76.96.4
dns2 203.76.127.4
Another
ip 122.144.9.24
Subnet 255.244.244.224
Gate way 122.144.9.1
dns 1 202.84.32.22
dns2 202.84.32.23
I have 3 internet line. How to connect it to a single network.
View 1 Replies View RelatedI was recently tasked at work to reinstall phone lines after a remodel. We have 2 phone lines with two phones and a credit card machine. I ran into a piece of equipment and I have no idea what it is so my research into the subject has been halted.
View 1 Replies View RelatedSo I am currently living in a fraternity with 60-70 other guys and our internet is slow at best. Currently we have 2 business connections from time warner cable and each of those connect to a apple wireless router. We dont have the speed i think we should and the range is very poor, and one of the routers seems to not work all the time.can give me to speed up the internet in my house,
View 3 Replies View RelatedBecause I have more than 10 mtrs of extension lead between my phone socket and my wireless router I am considering adapting my desktop computer to wireless.Will this speedup my broadband and improve my connection.?
View 2 Replies View RelatedI'm looking to increase my internet speeds as much as possible and was wondering how much my central splitter affects internet speeds? I have an ADSL splitter at the moment, im going to link 3 photos which shows the splitter and how it is wired. Also if you look at the black phone line which connects my house you can see that only two wires are being used (blue and white)? Is this the right setup for ADSL2 or should all 4 wires be connected to the splitter? Im getting only about 500kb/s download and 40kb/s upload max right
View 8 Replies View Related