Use Dlink DSL-2750U As Wireless Repeater?
Feb 15, 2013
I have a new internet router linksys EA2700 Firmware Version: 1.0.14, the wireless signal doesn't cover the whole house so I like to extend the wireless signal using my old router Dlink DSL-2750U as Access point, I configured the two router as following but yet didn't work.
Linksys
DHCP: enabled,
IP lease range 192.168.1.100 to 150
Wireless SSID, Security Mode, Passphrase, Channel Width and Channel number same as Dlink
Dlink:
DHCP: disabled
AP Mode: Access point
Bridge Restrict:Enabled
Remote Bridges MAC Address: is the linksys MAC.
And I removed the Layer2Interface and WAN old configuration.
View 3 Replies
ADVERTISEMENT
Sep 17, 2012
My Dlink DSL 2750u 3g internet wont stay active if my computer is off. My pc ain't quite a power saver.
View 1 Replies
View Related
Nov 6, 2011
I recently bought a new D-Link DIR 615 but I dont get adequate range in the rooms farthest away from the router. I have an old D-Link DIR 634M router which I'm told can be used as a wireless repeater. I went through several articles that describe connecting the two routers through a LAN cable. However is there a way to do the same without using a cable of any sorts?
View 1 Replies
View Related
Mar 7, 2012
I have already successfully upgraded the firmware to DD-WRT with no problems.What I want to do is have the D-Link DIR-601 Router set as a Repeater Bridge because I am trying to expand my wireless signal to dead spots in the house.I have NO SECURITY enabled on my NetGear Router and I am still unable to successully setup the D-link DIR-601 Router as a Repeater Bridge.
View 2 Replies
View Related
Jul 26, 2011
I have Dlink N300 router and also WRT54G2 router now with DD-WRT firmware, configured as a repeater.I have a PPPoE connection through Dlink router and want to extend signals farther, hence want to use Linksys (WRT54g2) as a repeater.I have set up the linksys as repeater but dont know how to check if its communicating with my Dlink and also I not able to get internet connection from the repeater.
View 5 Replies
View Related
Sep 4, 2012
make dlink dsl router 2640T to be working as repeater which will be able to receive wifi signals. I've seen one guy using the same dlink dsl-2640T as wifi signal repeater where he was successfully able to receive wifi signals[CODE]
View 5 Replies
View Related
Oct 28, 2012
I have D-link DSL 2750U wireless router. My PC and notebook are connected to router by Wi-Fi. They can share files or ping each other. I have a network storage unit plugged into router by an ethernet cable. Any of the computers cannot reach that storage unit or ping it. I guess my router isolates LAN network from WLAN network. Is there a way to combine them and get the router treat all devices connected to router in a single network?
View 1 Replies
View Related
Apr 23, 2012
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
View 2 Replies
View Related
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies
View Related
Apr 22, 2013
I started using a D-link 2750U wireless modem-router about 2 months ago, and configured it using the given disk for my ISP (MTNL Delhi). Since then, it has never retained a connection for more than 10 days, give or take i.e starts showing a red earth light instead of a green one. I usually reset it to factory settings and reconfigure it using the same disc over and over again, but now it has started dropping connection more frequently.Recently, it developed a new disease. Connection is very unstable now. Through line, it keeps disconnecting every 4-5 minutes. re-connects and dies again itself and does not work through wi-fi at allMy hardware quality healthy as I ran a wired connection for over 3 years without any trouble before this one.
View 1 Replies
View Related
Aug 6, 2012
configure my D-link wifi Modem DSL-2750U for Reliance Broadband.I dont understand codes but a simple explanation and step by step
View 3 Replies
View Related
Apr 25, 2012
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
View 6 Replies
View Related
Jul 28, 2012
i want to set up my wireless router it is currently set on a static ip but i want to set up in pppoe(username/password) mode i set up once in pppoe but internet is not working?
View 7 Replies
View Related
Feb 27, 2011
I have a PC connected to the internet via a d-link 615 router and a cable modem.The PC is hardwired to the modem and the laptop can connect wirelessly via the router.I own a HP 6280 Network MFD and would like to locate this in a separate room to the PC.I own a Linksys WAG54GS mobem router from my last ADSL connection.Can I site the wireless router with the MFD and use it as a wireless hub?
View 4 Replies
View Related
Dec 28, 2011
I have a new Dlink wireless router. Previously I had a Belkin router. The new one was said to have stronger signal. I am not able to connect via wireless to the router from a PC with Windows Vista. It works fine when I use a cable. Then I am able to connect to Internet via the router. Also, I am able to print on a wireless printer. It is also possible to use Internet from an Ipad with wifi.
The Belkin router had a different network, 192.168.2....When the cable is connected I can ping 192.168.0.1 but not when I remove the cable. In Windows Vista the connection has status "connected". When the cable is connected, the ipconfig /all is printed as below. It is a Swedish version. Some translated words:
Tr�dl�s = Wireless
Ja = Yes
Nej = No
Fr�nkopplad = Disconnected
[code]...
View 19 Replies
View Related
Nov 14, 2011
I have a Dlink DIR-615 wireless router. Without re-setting or changing the password I want to block my neighbour from using it as he knows my password
View 19 Replies
View Related
Jan 1, 2013
Every time i plug in my d-link DWA-125 usb wireless adapter, my computer "unplugs" my usb even though it is still plugged in.
View 4 Replies
View Related
Sep 6, 2012
I have a D-Link Router and I need to find the WEP number. How do I find it on my Router?
View 1 Replies
View Related
Jun 24, 2011
I want to make password for my dlink wireless
View 1 Replies
View Related
Nov 13, 2012
how i can configure dlink dl624
View 1 Replies
View Related
Jun 20, 2012
I've been using DIR-600 wireless router since an year. But, after having a factory reset i'm having a strange issue. When i'm configuring the router in the Dlink page(192.168.0.1 now i changed it to 192.168.1.100).. In that i go to Manual Internet Configuration>> then i select Static IP(Since i've been provided a static IP,gateway, DNS settings by my ISP) As soon as enter IP: 192.168.1.2,, and Subnet 255.255.255.0,,,Gateway : 192.168.1.1 and enter DNS details and press SAVE.. I get a message " Invalid IP Address".. I've set the Router IP as 192.168.1.100 and DHCP range : 3 to 199I don't know why is this happening.. I'm not able to connect to internet now from the router.
View 5 Replies
View Related
Mar 13, 2012
I've just installed a Netgear WDR4500 (n900) in my second floor office.The wireless range works great for multiple top floor computers as well as the 1st floor TV/ps3/tablet area.I am having some issue in the backyard and back deck though. (just something about my stucco walls)
So here is my question.I have my old DLINK dir-655. Would it be advisable to use a powerline connection (I already have Powerline adapters) to the ground floor near the back and piggyback the wireless?(This would also allow me to Hardwire the TV/ps3/htpc)
View 2 Replies
View Related
Oct 20, 2011
I have a fairly large home (>5000 sq ft) with multiple levels and some "dead spots" in the extreme areas. I would like to have a fantastic wi-fi signal through the home for access to my home network for my family and internet for guests. I have Fios with a 50/20 mpm with a "g" router. I also have purchased 2 repeaters (ampedwireless.com) and installed 1. Recognizing that it appears to have created a different network, so this isn't what I want to do. Then I went back and purchased 2 access points. I need to have an "hardware solution" in my theater (basement) as well as in my bedroom (3rd floor).
View 1 Replies
View Related
Oct 25, 2011
how do you setup a wireless repeater using a awus036h. Or is it even a option?
View 1 Replies
View Related
Jun 3, 2011
Iv had this problem with two wireless repeaters now. when im connected to just the router, i am able to access the internet. however when i plug in and set up the wireless repeater ( the latest one is a amped wireless sr300) it works for a few min and then i get a "DNS lookup failed" when trying to access sites. this repeater replaced a hawking hwren1. which would work for a few min and then lose the network.i believe this is a problem with our internet connection into the house, but could it be a caused by the router? (wrt400n) our isp says its not their problem and that its our router, but this is the 4th one in under a year.
View 2 Replies
View Related
Jan 21, 2013
I struggle getting a wireless internet signal in some parts of my house downstairs and all upstairs. Is a wireless router or repeater the same thing and which do I need.
View 3 Replies
View Related
Dec 26, 2012
As I am more of a hardware guy and pretty clueless about networking, I thought I'd come here because I am pretty frustrated right now.So yesterday, I got an Amped Wireless SR10000 Repeater for Christmas. I had it set up and working with no problems. However, this message did pop up when it was finished:
I ignored it (stupid me) because I didn't know what to do. The connection worked fine for a while, but now a day later, the connection keeps dropping. I would assume it is because of this.I did a bit of research and it seems like setting up a static IP will fix the problem, but I have no idea how to do that.
View 3 Replies
View Related
Mar 28, 2012
We have a home network which consists of one Motorola wireless router and 3 PCs. Two of the PCs connect directly to the wireless router without any issues, however, my PC dosent have a built in Wi Fi card so am using a TP Link wireless N USB adaptor.... so as you can imagine the signal is still very poor. So I have bought a TP Link AP and have it set up in repeater mode to increase the range of the router and thus improve my connection.
Now this works great in the short term as I get full signal, but the problem is the signal tends to drop out every 20 mins or so.Now, originally we were recieving an IP address conflict message which I thought was causing these drop outs, but I have rectified this by using MAC address filtering on the AP (think the AP was connecting to someone elses PC in our block of flats), but the drop outs still continue.
I have a static IP set on both my PC and AP and DHCP enabled on the Motorola router, I have also tried changing the Motorola's channel and moving the AP to different places but the story dosent change.I am a right noob when it comes to networking and have got this far by reading manuals, google searching and trail and error so dont know what else to do.
View 6 Replies
View Related
Feb 23, 2011
I want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together. I want to do it all wirelessly if possible.
View 1 Replies
View Related
Mar 22, 2011
Actually i´m working in a departamet of networking in my business with only cisco devices. I used to work with the wap200 wireless-G Acceess point (Small bussiness), but now i have a problem with it. I´m trying set the wap 200 as a wireless repeater for WRT54G but it´s a impossible.
View 1 Replies
View Related
Sep 21, 2012
I have spent countless weekends trying to configure the WAP 4410 as a wireless repeater. From what I see the instructions and help screens seem to be incomplete or the WAP is not capable of this function even though it is available.It will not connect to the modem wirelessly as a repeater. I have tried numberous settings including the same channel and SSID without avail. As soon as I disconnect it from the wireless modem it will no longer connect to the internet.I have an older WRT 610N which will connect to the modem as a repeater so I don't think it is at the modem end.Searches have indicated others with a similar problem but I don't see any viable solutions except to buy and connect to another WAP 4410.Contacting Cisco for suppor by chat t has been pointless. Either they are not available when I am or they are clueless.
View 5 Replies
View Related
Jul 20, 2010
I would like to ask for assistance on how to configure one unit WAP4410N access point to work as repeater to one unit WRT120N wireless router.
As a background, I had one WRT120N already in my house before I bought one WAP4410N as advised by a Linksys guy. I wanted to wirelessly extend the signal of my WRT120N wherever its signal is so low around my house. The WAP4410N should work as repeater to WRT120N.
I already configured WAP4410N to work as repeater by enabling all the choices in its wireless AP mode like the “wireless WDS repeater” and the “wireless client/repeater” but to no avail. I successfully setup a similar scenario before using the old pair of one WRT54G and one WAP54G. I replaced the old pair with the newer one ( WRT120N and one WAP4410N).
Is the tandem of WAP4410N and WRT120N can be configured technically as like as what I wanted? Do I need to upgrade the firmware of both devices? Did I miss something in the configuration?
View 2 Replies
View Related
Mar 9, 2011
We have a WAP4410N as a Access Point and a second WAP4410N as a Wireless WDS Repeater. The settings are as of below.
We couldn't get the mobile users to get connected to the Access Point. But if we uncheck the option "Allow wireless signal to be repeated by a repeater.", it works.
View 4 Replies
View Related
