I have a PC connected to the internet via a d-link 615 router and a cable modem.The PC is hardwired to the modem and the laptop can connect wirelessly via the router.I own a HP 6280 Network MFD and would like to locate this in a separate room to the PC.I own a Linksys WAG54GS mobem router from my last ADSL connection.Can I site the wireless router with the MFD and use it as a wireless hub?
View 4 RepliesI'm trying to set up a site to site VPN link between the ASA5510 that we use exclusively as a VPN endpoint on campus and a D-Link DIR130 VPN Router off campus, at a local business with a dynamically assigned IP. We currently use the ASA for remote access users who use the Cisco VPN client on mobile devices, as well as for a single site to site link to our telecom provider for the purposes of monitoring telecom equipment remotely.We are looking for a way to cheaply deploy secure VPN connections to local businesses to allow them to use point of sale devices which connect back to systems on campus, so students can use their meal cards at local restaurants, similarly to how they use them at the on-campus cafeteria.
I have experience configuring Cisco switches, APs and routers, but this ASA device absolutely baffles me. I've futzed around with the ASDM 6.4 gui config and tried to match up configurations between the DIR130 and the ASA, but I can never get a VPN connection to come up.
I have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies View Relatedi want to set up my wireless router it is currently set on a static ip but i want to set up in pppoe(username/password) mode i set up once in pppoe but internet is not working?
View 7 Replies View RelatedI have a new Dlink wireless router. Previously I had a Belkin router. The new one was said to have stronger signal. I am not able to connect via wireless to the router from a PC with Windows Vista. It works fine when I use a cable. Then I am able to connect to Internet via the router. Also, I am able to print on a wireless printer. It is also possible to use Internet from an Ipad with wifi.
The Belkin router had a different network, 192.168.2....When the cable is connected I can ping 192.168.0.1 but not when I remove the cable. In Windows Vista the connection has status "connected". When the cable is connected, the ipconfig /all is printed as below. It is a Swedish version. Some translated words:
Tr�dl�s = Wireless
Ja = Yes
Nej = No
Fr�nkopplad = Disconnected
[code]...
I have a Dlink DIR-615 wireless router. Without re-setting or changing the password I want to block my neighbour from using it as he knows my password
View 19 Replies View RelatedI recently bought a new D-Link DIR 615 but I dont get adequate range in the rooms farthest away from the router. I have an old D-Link DIR 634M router which I'm told can be used as a wireless repeater. I went through several articles that describe connecting the two routers through a LAN cable. However is there a way to do the same without using a cable of any sorts?
View 1 Replies View RelatedI have a D-Link Router and I need to find the WEP number. How do I find it on my Router?
View 1 Replies View Relatedhow i can configure dlink dl624
View 1 Replies View RelatedI've been using DIR-600 wireless router since an year. But, after having a factory reset i'm having a strange issue. When i'm configuring the router in the Dlink page(192.168.0.1 now i changed it to 192.168.1.100).. In that i go to Manual Internet Configuration>> then i select Static IP(Since i've been provided a static IP,gateway, DNS settings by my ISP) As soon as enter IP: 192.168.1.2,, and Subnet 255.255.255.0,,,Gateway : 192.168.1.1 and enter DNS details and press SAVE.. I get a message " Invalid IP Address".. I've set the Router IP as 192.168.1.100 and DHCP range : 3 to 199I don't know why is this happening.. I'm not able to connect to internet now from the router.
View 5 Replies View RelatedI would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
hsrp+bgp+site to site vpn on router 2811.
View 2 Replies View Relatedmy internet has been acting slow, i have a dlink router 615 and high speed comcast internet
View 4 Replies View RelatedRecently the router has been dropping the wireless connection, and now is not connecting with the computer - the ethernet still works. It was suggested to upgrade the firmware but I can't access the configuration.I've tried admin, and blank password which is supposed to be the default. I've also tried XXXXX as password, and another username and password in case I had altered it for security.It doesn't allow me in.
View 13 Replies View RelatedI tested my network throughput speed and it's pitiful. 11Mbit/s or 1450 KB/s! I am running the test from two wireless machines connected via a wireless N router(DLink DIR-655). Both are in good range.I am using the Microsoft NTttcp tool to test my network throughput.
View 3 Replies View RelatedCan I use my d-link wireless router to send movies to my hd tv?
View 3 Replies View RelatedCan I connect Magic-Jack to Dlink -655 wireless router ?I want to connect MJ direct to Dlink 655 wifi wireless router so I can make phone call without turn on computer?
View 2 Replies View RelatedI am trying to set up a Site to Site between two RV042 with static IP at both routers.at the log at site 1 i get: packet from XX.XXX.XX.167:5: initial Main Mode message received on 10.2.32.1:500 but no connection has been authorized with policy=PSK.At site 2 i get: packet from xxx.xxx.xxx.146:500: initial Main Mode message received on 192.168.1.1:500 but no connection has been authorized with policy=PSK.I have tuned off the firewall and added a Port forwarding to the router ip and port 500.Tried with different autentication methods, but get the same message.
View 1 Replies View RelatedI have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies View RelatedI need to configure a site-to-site VPN using a Cisco 881 router on my end and connecting to an ASA5510 on my suppliers end.Our supplier has configured their end and I do not have access to their configuration.
They told us we have to NAT all inside address' to a single address (192.168.89.1) as this is the only one they will let through their firewall/tunnel.I know how to set up the VPN but not too sure how to set up the NAT part.
My sanatized config is attached. The code I am using to NAT my inside network to the single address 192.168.89.1, and send all traffic accross the VPN tunnel as this address is correct? With the router running this config the VPN tunnel does not connect.
I have an issue with 2 site to site VPN tunnels from a RV042G router. The issue is for both VPN tunnels is that in the logs, it is showing that when the RV042G router is trying to establish the tunnel, it is getting a response from the remote gateway internal address and not the Public address of the remote gateways. On the remote gateways I have other site to site VPN's terminating fine and the tunnels are passing traffic. I only have an issue with the RV042. On the VPN Tunnel page it shows for both tunnels waiting for connection. This is an output from the log of the RV042G
Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: Peer ID is ID_IPV4_ADDR: '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: Peer ID is ID_IPV4_ADDR: '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: sending encrypted notification INVALID_ID_INFORMATION to 203.47.XXX.XX:500
VPN tunnel terminating on 203.43.XX.XXX is a Checkpoint firewall running R70 software version?VPN tunnel terminating on 203.47.XXX.XX is a Cisco ASA 5510 running ASA 8.2.4 software?As stated above, I have other VPN tunnels working fine. This RV042 is a replacement router as the original router suffered a power surge.
Just now my boss asked me to prepare to set up site-to-site VPN on Cisco 881 Integrated Services router to ASA 5505 router which is now running at the HQ side. I am now learning pdf file from Cisco which mention how to setup site-to-site VPN between Cisco 1812 IOS router and ASA 5505 router by using ASDM V6.1 and SDM V2.5. Can't find the paper for that Cisco 881 device.
View 4 Replies View RelatedI am trying to create a site to site VPN using a cisco 2901 and Linksys router.I have the VPN configured and connected and I can ping gateway to gateway. However, from the Cisco I can't ping any of the devices beyond the gateway.Example, from the cisco I can ping 192.168.5.254 (gateway IP address) source gig 0/1 and it works great.
However if I ping from the cisco 192.168.5.50 (end user PC) source gig 0/1 it doesn't work.I have created a client VPN and that works perfectly.Below is my config.
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 2
[code]....
I have Cisco 877 routers, with ethernet (LAN) and ADSL (external) interfaces. The ADSL interface gets dynamic IP. Is Site to Site VPN with Dynamic IP and Internet Browsing Possible on the Same Router.
View 4 Replies View RelatedI'm setting up a site-to-site VPN between two offices, Site A uses a Cisco RV110W VPN Router with a static WAN IP and local IP 192.168.1.0/24 while Site B I have set up with a Belkin N300 VPN router which also has a Static WAN IP and the local IP is set to 192.168.2.0/24
I'm able to ping from Site B (192.168.2.xxx) to Site A, however I can't communicate from Site A back to Site B.how I could go about troubleshooting this? I've been scouring the internet for 3 days trying to get to the bottom of this with no luck.
I have recently bought two CISCO routers RV220W for our main and brach office mainly for VPN tunneling. I didnt know they are routers only not modems. so I have set it up using BT 2wire Router as modem only.
I have successfuly setup the routers and manage to establish the VPN tunneling between two routers. AS bt doesnt give static WAN IP address so I have used Dyndns which works fine. although I have 5 static ip address which cannot be used for WAN unless i cahnge to one IP address even then BT tech said it will not work.
when I created the tunnel i could ping both servers with their IP only not with the names. I can ping them fine locally. I could also see the network from branch office to main office but not from main office to branch office. today when I restarted the server I cannot ping both server i mean vice versa but VPN tunnel is established. now I cannot see the network from branch office to main office as well.
Both sites running windows server 2008 standard. main office server has 6 NIC cards two wwith public and three with private ip addresses, its also runing Terminal server, exchange, file etc. the branch office has two NIC card one with private and one with public ip. Intially I could establish the VPN tunnel as the network range was same on both sites so I changed one in th e10.0.0.0 range other in 192.168.1.0 range and VPN tunnel was established straightaway.
As soon as the VPN tunnel was created I manage to creat an external trust without any problems and both servers are added in each other forward zones as name servers.
in the main office the fues went off and I had to re-start the router and now the VPN tunnel is not establishing, mainly the error is ISAKMP-SA Expired I will paste the log of both routers below
1. How to Clear Old or Existing Security Associations (Tunnels) on RV220W
2. how to fix the problem where I can ping the server with their IP as well as domain names ?
3. how to set it up so that both sides can see the network resources as well as access it ?
4. how to set it up so if the staff in branch office wants to log on the domain in main office he can simply do it as he does it in his office.
how to configure a site to site tunnel using IKEv2 between our offices using an ASA 5515-X and a Cisco 3925 router running IOS 15.2 Connecting ASA to ASA and ASA to Router via IKEv1 works fine. Want to take advantage of the improvements in IKEv2 but I'm having difficulty with the ikev2 setup on the router. Here is the pertinent ASA side config--
ASA IP: 5.5.5.5
Router IP: 10.10.10.10
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1
[Code].....
I was traying to make a site to site VPN between a cisco 1800 router and cisco asa 5510. But it was impossible to get it. [code]
View 1 Replies View RelatedI have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View Relatedhow to configure a site-to-site VPN between RV042 router and 1941 router?
View 0 Replies View RelatedI'm setting up site to site VPN on a RV110W router. The administrator guide site to site instructions don't match the options on the router.The first step tells you to click on VPN then Basic VPN Setup. The router under the VPN option only has three choices, (1) VPN Clients, (2) Certificate Management and (3) VPN Passthrough. I have upgraded to the latest firmware 1.0.0.9.
View 4 Replies View Relatedwhat is going on message" MM_NO_STATE ". i'm not clear about this for documents they said that MM_NO_STATE-The Internet Security Association and Key Management Protocol (ISAKMP) SA has been created but nothing else has happened yet."but i still don't know that is the main problem? Note: i used Cisco router 2821 and Cisco router 1841 ( and configure VPN site to site)
View 4 Replies View Related