I tested my network throughput speed and it's pitiful. 11Mbit/s or 1450 KB/s! I am running the test from two wireless machines connected via a wireless N router(DLink DIR-655). Both are in good range.I am using the Microsoft NTttcp tool to test my network throughput.
View 3 RepliesAbout 3 or maybe 4 years ago I bought a Dlink DIR-655 wireless router.On the box it listed it as an Xtreme N Gigabit Router, Wireless N (Draft N). I've had two Windows PCs connected to this router by Cat5 with "Intel 82562V-210 10/100 Network Connection" NICs on each set to "Auto detect". The link speed on the NICs show as 100Mbps.Also, I have an MBP and a Windows laptop that connects to this router at times, both with built-in wireless cards.I have Insight Cable and a 20Mbps download and 1.38 upload speeds.This router has worked great for the past years. Since it was getting a little old, I thought I would buy another just like it to have when this one defaults.I ordered a replacement from Amazon. The picture of the router at Amazon was the same as the one I have now.When the router arrived, it was a Dlink DIR-655; however, the router had a different faceplate and larger lights.On the box it listed it as "Xtreme N Gigabit Router". Also listed was N+ 300.
When I set the new DIR-655 up for my LAN and wireless, everything worked OK.However, I noticed the link speed on the NICs had dropped to 10Mbps.I can disable the NIC and then enable, or, unplug and plug in the Cat5 cable, and it will connect at 100Mbps for about 5 seconds and then revert back to 10Mbps.I returned the router to Amazon and purchased another just like it from Office Depot.The same problems are back.I have used the router set-up disk and have done a manual set-up. I cannot get the NICs to connect to the router above 10Mbps.I have turned off wireless, made different settings throughout the router and nothing works.I can set the NICs to 100Mbps full duplex and I get 1.5Mbps download speeds. If I set them to 100 half duplex, I might get 5Mbps.Believe me; I have just about changed every setting on this router with no success. I've turned the firewall, QoS off then on, wireless off and on, put one PC outside the router, but nothing works. Also, firmware is up to date.When I connect my PC direct to Insight modem or connect the original DIR-655, I get 100Mbps on the NIC and 20+Mbps download speed.I cannot get the NICs to connect above 10Mbps on this "new DIR-655" router.
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View Relatedi want to set up my wireless router it is currently set on a static ip but i want to set up in pppoe(username/password) mode i set up once in pppoe but internet is not working?
View 7 Replies View RelatedI have a PC connected to the internet via a d-link 615 router and a cable modem.The PC is hardwired to the modem and the laptop can connect wirelessly via the router.I own a HP 6280 Network MFD and would like to locate this in a separate room to the PC.I own a Linksys WAG54GS mobem router from my last ADSL connection.Can I site the wireless router with the MFD and use it as a wireless hub?
View 4 Replies View RelatedI have a new Dlink wireless router. Previously I had a Belkin router. The new one was said to have stronger signal. I am not able to connect via wireless to the router from a PC with Windows Vista. It works fine when I use a cable. Then I am able to connect to Internet via the router. Also, I am able to print on a wireless printer. It is also possible to use Internet from an Ipad with wifi.
The Belkin router had a different network, 192.168.2....When the cable is connected I can ping 192.168.0.1 but not when I remove the cable. In Windows Vista the connection has status "connected". When the cable is connected, the ipconfig /all is printed as below. It is a Swedish version. Some translated words:
Tr�dl�s = Wireless
Ja = Yes
Nej = No
Fr�nkopplad = Disconnected
[code]...
I have a Dlink DIR-615 wireless router. Without re-setting or changing the password I want to block my neighbour from using it as he knows my password
View 19 Replies View RelatedI recently bought a new D-Link DIR 615 but I dont get adequate range in the rooms farthest away from the router. I have an old D-Link DIR 634M router which I'm told can be used as a wireless repeater. I went through several articles that describe connecting the two routers through a LAN cable. However is there a way to do the same without using a cable of any sorts?
View 1 Replies View RelatedI have a D-Link Router and I need to find the WEP number. How do I find it on my Router?
View 1 Replies View Relatedhow i can configure dlink dl624
View 1 Replies View RelatedI've been using DIR-600 wireless router since an year. But, after having a factory reset i'm having a strange issue. When i'm configuring the router in the Dlink page(192.168.0.1 now i changed it to 192.168.1.100).. In that i go to Manual Internet Configuration>> then i select Static IP(Since i've been provided a static IP,gateway, DNS settings by my ISP) As soon as enter IP: 192.168.1.2,, and Subnet 255.255.255.0,,,Gateway : 192.168.1.1 and enter DNS details and press SAVE.. I get a message " Invalid IP Address".. I've set the Router IP as 192.168.1.100 and DHCP range : 3 to 199I don't know why is this happening.. I'm not able to connect to internet now from the router.
View 5 Replies View Relatedmy internet has been acting slow, i have a dlink router 615 and high speed comcast internet
View 4 Replies View RelatedRecently the router has been dropping the wireless connection, and now is not connecting with the computer - the ethernet still works. It was suggested to upgrade the firmware but I can't access the configuration.I've tried admin, and blank password which is supposed to be the default. I've also tried XXXXX as password, and another username and password in case I had altered it for security.It doesn't allow me in.
View 13 Replies View RelatedCan I use my d-link wireless router to send movies to my hd tv?
View 3 Replies View RelatedCan I connect Magic-Jack to Dlink -655 wireless router ?I want to connect MJ direct to Dlink 655 wifi wireless router so I can make phone call without turn on computer?
View 2 Replies View RelatedI have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
The router's software was installed on our desktop years ago and now, the desktop is quite old and we have to sell it. I need to know if we need to reinstall the software again in probably in one of the laptops at home.
View 2 Replies View RelatedI want to edit existing wireless network in DLINK router. But I can't find any option to do it. If I go to "wireless settings" option, it shows the three options "wireless network setup wizard", "add wireless device with WPS", "manual wireless network setup", but I cannot find any option to edit the wireless network that was already set up.
View 3 Replies View RelatedIts a Toshiba laptop and she has a d-link 2680 wireless router. The laptop will successfully connect to the internet through an ethernet cable, and will connect to the wireless network fine but when wireless i cannot access the internet. I have an iphone which connects to the wireless network and accesses the web perfectly.I have tried everything I can think of and find online to try and talktalk tech support won't assist as its a hardware setup issue.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Barbara-laptop
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
[code]...
My Dell Dimension is no longer connecting to the internet via the wireless router. I have a dlink DI-524 and a dlink wireless USB key but it no longer connects. This just started today. When I try to repair the connection, it fails on "renewing IP".
OS is Windows XP.
P.S. I have tried power cycling the modem/router but nothing works. Other computers can get on the internet via the wireless router fine.
my dlink dsl-520b dls modem is using 192.168.1.1 and is plugged into the WAN port on my dlink wireless router.the wireless router is 192.168.0.1. (these are both in the main building which is remote from my shop).Then i have a netgear wireless access point This spreads the signal properly, and I can get connectivity on all my computers -although i do have to specify a default route on the computers on my shop side of the access point.I noticed that the internet light on my modem is red which indicates no internet connection. I am still able to access the internet fine, but i would like to be able to log into the modem from my network. I was able to do this before by setting a computer with a netmask of 255.255.0.0.
View 6 Replies View Relatedconnect usb printer to d-link n2760 router i plugged in the printer diagnsotic failed
View 2 Replies View Relatedhow to change security settings so my kids can go online on their nintendo ds lite. we have d link router. 192.168.0.1
View 1 Replies View RelatedMy dlink dir 628 wireless router suddenly stopped working yesterday. If I plug the ethernet cable directly into my computer and the internet works. I see the wireless profile in the options for the wireless internet, but when I try to connect, it is unable to do so.
I've tried resetting the router (using the button on the device) witand reinstalling the router (using the CD), but still not working. Also have tried turning off the modem, router, and restarting my computer.
I have a dlink(wireless n-300) router going through a netgear wireless g router, i have an intel wifi link 5100 agn in my acer aspire 6930g laptop & the isp is high speed cable (Shaw cable). My question is, why does my computer have to reset the router every minute or so? It takes forever to get anything on the web which could be Bitdefender 2012 plus security?
View 1 Replies View RelatedI changed the router ip to 192.168.0.2 from 192.168.0.1. I don't know what type of connection, i have to use. It have the following options: Static IP, DHCP etc. The internet connectivity status shows 'disconnected'.I'm currently using the lan to connect to net. ISP gave me a username and password to Login with a browser to start browsing. Since multiple devices are use in same connection, they provided 2 IP.
View 1 Replies View RelatedWe are using a Westell 7500 wireless modem/router from Frontier without any problemsI have two d-link wireless n300 routers that I want to add to network so I can add them to our DirecTV DVR's. I have tried using the D-link CD and instructions without any success. Everytime it prompts me for my 1st router's (the Westell's) login/password, it says it's invalid. If I then click to continue w/o the logon and password, it then gives me an error when it is trying to add the d-link. I have tried everything. My Westell IP is 192.168.1.1. How can I access and add the d-link routers? Is there an easier way?
View 16 Replies View RelatedHow do I install a D-Link Wireless router, DIR 655 to the Verizon Fios internet. I have tried different ways but cant get it to work.
View 13 Replies View Relatedtrying to connect an old PC to my home wireless network.I brought home a PC I have used for years at my office. I have it configured with a Realtek wireless card and was able to connect it to my office wireless network without a problem.But, when I try to set it up at home, it won't take. I have a dlink router that is working fine with several Mac computers in my home, so I know the router and network are up and running fine.The PC uses Windows XP. The icon in the lower right corner says dlink is connected and there is strong signal strength. However, when I check the dlink status, it shows that 2,573 "packets" are sent, while "0" are received.I've tried to connect to the internet using Mozilla, Safari, and Explorer. Each says the server cannot be found and that the internet is not connected.
View 5 Replies View RelatedHave D-link N150 wireless router as access point working with D-link DLG4100 wired router Forgot password for N150. How to find or reset it?
View 1 Replies View RelatedI have just purchased a new ASUS Laptop for my wife.We are currently running two destop computers on a D LinK Router. How do I go about including the new computer on the network wirelessly?What do I need to purchase to make the transition easiest? The two desktops are running Windows XP Professional, the new system is Windows 7.
View 4 Replies View RelatedI started the FTP Server at the dlink and forwarded port 80 and port 21 to the ipadress from my NAS, surely i activated it. Port 80 for the webmask Port 21 for the FTP server. If i connected me at my homenetwork and typ in my browser: ftp://"username".dyndns.org the ftp server works, also the webmask from the Sharecenter. If i want to connect me from my work or other pc's, the ftp didn't work. can't ping "username".dyndns.org
View 1 Replies View Related