D-Link DIR-601 :: Setting Up A 601 As A Wireless Repeater?

Feb 23, 2011

I want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together.  I want to do it all wirelessly if possible.

View 1 Replies


ADVERTISEMENT

D-link DIR-655 :: Setting Up Access Point / Repeater For Home Network

Jul 21, 2011

I am looking for an equipment recommendation for setting up an access point/repeater for my home network.

I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like

comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop

View 2 Replies View Related

Cisco Wireless :: Setting Up Another WAP4410N As Repeater?

Apr 20, 2011

Currently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.

The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:

Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater

Below is the link from cisco with explanation. [URL]

Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.

View 9 Replies View Related

Cisco Wireless :: Setting Up WAP4410n As Repeater

Apr 20, 2011

I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated.  So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?

View 1 Replies View Related

Cisco Wireless :: Setting Up WAP4410n V 2.0.1.0 As Repeater?

Apr 30, 2011

Setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.

View 2 Replies View Related

Cisco Wireless :: ACS 5.2 / Setting Up APs In Root Repeater?

Sep 16, 2012

I am trying to configure repeater mode on an AP, but the authentication is not working.It seems the authentication is seen as EAP-TLS on the ACS 5.2, but im trying to do LEAP.
 
Relevant config root AP:
 
!
dot11 ssid Auto3
   authentication open eap eap_methods
   authentication network-eap eap_methods1
   guest-mode
   infrastructure-ssid

[code].....

View 8 Replies View Related

Cisco Wireless :: Setting Up WAP200 As Repeater?

Oct 12, 2010

I'm trying to setup a WAP200 as a wireless repeater and I am having some problems. The SSID I am trying to bridge is coming from a WRV210.
 
I on both devices I have the SSID, security, and channel set the same. The WAP200 is set to Repeater mode and I did a site survey to find the WRV210. The WRV210 is set to to allow the WAP200 repeat its signa using auto select, manual with site survey and manual actually entering the MAC address by hand.
 
Nothing seems to work. I can see the wireless next work but when i connect to the repeater I never get an IP address.

View 2 Replies View Related

Linksys Wireless Router :: Setting Up A WRH54G As A Repeater?

Jul 10, 2011

My house is a little too big for my WRT160N v3 to be able to get to every room, so i was wondering if i could set up my old WRH54G as a repeater to get that extra distance to get those last room on the network? if so how to set up the connection?

View 1 Replies View Related

Linksys Wireless Router :: Setting Up EA4500 As Repeater?

Jan 17, 2013

I have EA4500 router that connects a couple of desktops in one room. I am having to setup another room for gaming for which I have another EA4500 router. I want to setup the second EA4500 uplink(accesspoint) as the first EA4500. I dont find any interface to do it. I am able to do it wired(by connecting the both the routers through LAN ports). but I dont want to run cable across the house.  know if it is possible with another firmware. Or should I return this new EA4500 and buy another router?

View 2 Replies View Related

Cisco Wireless :: Setting Up Aironet 1142n As Repeater?

Aug 9, 2012

I've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
 
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
 
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
 
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
 
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?

View 3 Replies View Related

Cisco Wireless :: Setting RV180W In WDS Bridge And Repeater Without Any Different Result

Oct 14, 2012

I recently bought one RV180W and two WAP121 in order to make a wireless extension of a network.I configured RV180W as Router and the three of them have the same SSID and password.Also, I added in RV180W WDS configuration both MAC Addreses of WAP121's and in WAP121's WDS configuration the MAC Address of RV180W.Even I tried in WAP121's with and without encryption using the same WPA Key of the RV180W.
 
The thing is that is not working at all. They work great separately but right WAP121 can't stablish WDS link with RV180W neither do the left WAP121 with RV180W.I tested WDS configuration of WAP121's and they can see each other between them using standard WDS configuration, so I assume that WDS function of WAP121's works great.Finally I try the same config but setting RV180W in WDS Bridge and WDS Repeater without any different result.Do I have any chance to make the topology I showed up would work? How do I have to configure the RV180W and WAP121's?

View 1 Replies View Related

Cisco Wireless :: Setting Up Wireless Repeater Using 1242AG Access Points?

Jul 4, 2011

I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs  and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it.  There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
 
WLC (LEAP with local users) -----> LAP ----> Repeater AP
 
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.

View 1 Replies View Related

Setting Up A Repeater Router?

Sep 26, 2011

I have a very large house with many people using wireless laptops. i used to have verizon internet and I purchased a wlan 11g mini router from radio lads. After it was set up it worked great. I have just switched to comcast internet (my first mistake) and I can't get the mini router to work.

View 1 Replies View Related

Setting Up Repeater In Engenius 9550?

Jan 3, 2013

I have a lynksys router hard wired and wifi. It is eworking fine when I tried to set up a new Engenius 9550 router as a repeater I can't get the settings correct. I have reset the 9550 twice and still won't reconize the rounter in the home network.proper settings for the 9550.

View 12 Replies View Related

Setting Up Netgear WNR2000 Router As A Repeater

Jul 22, 2011

ok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.

View 4 Replies View Related

Setting Up Netgear WNR2000 Router As A Repeater?

Jul 4, 2011

I have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.

View 1 Replies View Related

M1424-WR - Setting Up Repeater With Verizon FiOS Router?

Jan 7, 2012

Set up a repeater for their house to get a better signal in locations farther from their main router that is a Verizon Actiontec M1424-WR Rev. C. I am recommending that he get an old router (Linksys wrt54GL or E2000) that I can convert into a repeater with DDWRT firmware as a cheap solution, or with a purpose built Netgear or Linksys range extender repeater as a more $ solution.

View 4 Replies View Related

Linksys Access Point :: Setting Up AP2 WAP4410N To Be A Repeater For AP1?

Oct 12, 2011

I have AP1 setup with WPA2-Enterprise.  How would I setup AP2 (WAP4410N) to be a repeater for AP1?

View 1 Replies View Related

Cisco Routers :: Setting Up WAP4410N As Repeater To Extend Signal Of E2500?

Apr 18, 2012

Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
 
I tried steps as below:
 
1. Same password type in WAP4410N and E2500.

2. Different password type in WAP4410N and E2500.

3. Set password in WAP4410N ONLY.

4. Set password in E2500 ONLY.
 
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.

View 2 Replies View Related

D-Link DIR-601 :: Can Make A Wireless Bridge Or Repeater

Nov 15, 2011

i just happened to have a spare DIR 601 and I already installed DDWRT on it. Now my question is can make this as a wireless bridge or repeater? with only using the signal of my DIR 655 router upstairs?

View 4 Replies View Related

TP-Link ADSL2+ Wireless :: TD8951ND - Possible To Use Router As Repeater

Apr 29, 2013

Region : Others
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Nepal Telecom

My router said it has Wireless Access Point and WDS.I think to use this router as a repeater?

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: Repeater On TD-W8151N With TL-WR740N?

Dec 22, 2012

Region : Vietnam
Model : TD-W8151N
Hardware Version : V1
Firmware Version :
ISP :

I'm using a Tp-Link's Product (TD-W8151N). But now, i want to using TL-Wr740N repeat the Wifi from TD-W8151N. How can i do that?

View 2 Replies View Related

D-Link DIR-655 :: Wireless Range Extender Or Repeater / Booster

Nov 20, 2011

I am moving my office from one side of the house to the other which has real spotty wireless coverage. Most likely I will not be able to move the modem or wireless router, so I have to somehow increase the range.I did some research and poking around on forums, but I can't find a clear cut, number 1. What you think would be the best option to pair with the DIR-655.

View 1 Replies View Related

D-Link DIR-655 :: Configure To Join Existing Wireless Network As Repeater

Jan 29, 2011

I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment.  But I don't see any way to configure the device to join an existing wireless network.  Am I wasting my time?

View 7 Replies View Related

D-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect

Apr 12, 2011

I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?

View 1 Replies View Related

TP-Link TD-W8960N - How To Use Thomson Speed Touch TG587nv2 As Secondary Wireless Repeater

Feb 10, 2012

I am using a TP-Link TD-W8960N as my main router with ADSL connection. It works fine but on the top floor our signal is pretty low. I want to us the Thomson SpeedTouch TG587nv2 (O2 Wireless box IV) as a secondary wireless repeater. I can't use a ethernet cable between them. I want to make a wireless bridge or use WDS.

View 3 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR702N - Repeater Mode Signal Fades Out Or Does Not Work At All

Jan 31, 2013

Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST

This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.

View 1 Replies View Related

Tp-link 150mbps Wireless :: Wr700n Difference Between Wifi Range Extender And Repeater

Apr 9, 2013

Region : Singapore
Model : TL-WR700N
Hardware Version : V1
Firmware Version :

Since i know there's a "Repeater Operation Mode" in TL-WR700N Wireless Lan Mini Pocket Router, so what's the difference between TL-WA850RE WiFi Range Extender?I know the maxium speed support is different, but.... what else ?

View 1 Replies View Related

A Repeater For D-Link DI-624?

Oct 23, 2011

I have a D-Link DI-624 router and I understand that I can convert this router to a repeater using on line software thus allowing me to extend a wireless signal from up to a 1/4 mile away

View 1 Replies View Related

D-Link DIR-825 :: Using As A Repeater?

Aug 16, 2011

I was wondering if it possible to use the DIR-825 as a repeater. My main router is a Airport Extreme but it doesn't reach the whole house. Now what I'm also wondering if I can use the repeater as well as a SharePort for my external hard drive while it is being used as a Repeater.

View 4 Replies View Related

Wireless :: 192.168.0.50 Setting Up D-Link DAP-1360

Sep 21, 2011

I am trying to setup D-Link DAP-1360 as a range extender, but am unable to see the device from my browser. The IP address is given to be 192.168.0.50. My router IP address is 192.168.1.1 and my PC IP address is 192.168.1.34.

View 11 Replies View Related

Put D-Link DIR-615 C1 In Repeater Mode?

Oct 5, 2012

I just recently upgraded my home router from a 615 to a 655, so I thought I would use the old router as a repeater bridge at another location.

I read that the DD-WRT firmware offered a repeater bridge function, so I successfully flashed the 615 C1 with the latest release 7/12.

I get all of the configuration steps, and even have set up client bridge mode. My problem is when I bring down the list of available wireless modes, repeater bridge isn't on the list.

Is the C1 version not able to do this? is there something else I need to do to enable a repeater bridge?

View 4 Replies View Related

D-Link DAP-1522 :: Nothing Showing In Wireless Setting?

Mar 23, 2011

I got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.

I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.

Am I doing something wrong or will the DAP-1522 not do this?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved