I have a lynksys router hard wired and wifi. It is eworking fine when I tried to set up a new Engenius 9550 router as a repeater I can't get the settings correct. I have reset the 9550 twice and still won't reconize the rounter in the home network.proper settings for the 9550.
View 12 RepliesI just got a wireless repeater (Engenius ERN 9250) to use in my house, and I'm having issues after setting it up. I set it up using the WPS function with my router (netgear n600), and even if I connected to the repeater my internet would not work. I could access the repeaters admin page wirelessly, and I could ping it (192.168.1.2) just fine. However, if I tried to ping the router it would not work. I made sure that the repeater was connected to my router through the admin page, and I made sure to set the default gateway on the repeater to 192.168.1.1.
View 12 Replies View RelatedI'm trying to install an Engenius EAP9550, configured as a wireless repeater. the instructions are beyond abominable (as the review on Amazon warned). They tell me to enter 192.168.1.1 (which is my linksys E2000 wireless routers address, though they say nothing about that) and tehn give me no other information on how to configure or set this up.
View 13 Replies View RelatedI have a very large house with many people using wireless laptops. i used to have verizon internet and I purchased a wlan 11g mini router from radio lads. After it was set up it worked great. I have just switched to comcast internet (my first mistake) and I can't get the mini router to work.
View 1 Replies View RelatedI want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together. I want to do it all wirelessly if possible.
View 1 Replies View Relatedok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies View RelatedI have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies View RelatedCurrently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.
The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:
Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater
Below is the link from cisco with explanation. [URL]
Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.
I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?
View 1 Replies View RelatedSetting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.
View 2 Replies View RelatedI am trying to configure repeater mode on an AP, but the authentication is not working.It seems the authentication is seen as EAP-TLS on the ACS 5.2, but im trying to do LEAP.
Relevant config root AP:
!
dot11 ssid Auto3
authentication open eap eap_methods
authentication network-eap eap_methods1
guest-mode
infrastructure-ssid
[code].....
I'm trying to setup a WAP200 as a wireless repeater and I am having some problems. The SSID I am trying to bridge is coming from a WRV210.
I on both devices I have the SSID, security, and channel set the same. The WAP200 is set to Repeater mode and I did a site survey to find the WRV210. The WRV210 is set to to allow the WAP200 repeat its signa using auto select, manual with site survey and manual actually entering the MAC address by hand.
Nothing seems to work. I can see the wireless next work but when i connect to the repeater I never get an IP address.
Set up a repeater for their house to get a better signal in locations farther from their main router that is a Verizon Actiontec M1424-WR Rev. C. I am recommending that he get an old router (Linksys wrt54GL or E2000) that I can convert into a repeater with DDWRT firmware as a cheap solution, or with a purpose built Netgear or Linksys range extender repeater as a more $ solution.
View 4 Replies View RelatedI have AP1 setup with WPA2-Enterprise. How would I setup AP2 (WAP4410N) to be a repeater for AP1?
View 1 Replies View RelatedMy house is a little too big for my WRT160N v3 to be able to get to every room, so i was wondering if i could set up my old WRH54G as a repeater to get that extra distance to get those last room on the network? if so how to set up the connection?
View 1 Replies View RelatedI have EA4500 router that connects a couple of desktops in one room. I am having to setup another room for gaming for which I have another EA4500 router. I want to setup the second EA4500 uplink(accesspoint) as the first EA4500. I dont find any interface to do it. I am able to do it wired(by connecting the both the routers through LAN ports). but I dont want to run cable across the house. know if it is possible with another firmware. Or should I return this new EA4500 and buy another router?
View 2 Replies View RelatedI've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
I recently bought one RV180W and two WAP121 in order to make a wireless extension of a network.I configured RV180W as Router and the three of them have the same SSID and password.Also, I added in RV180W WDS configuration both MAC Addreses of WAP121's and in WAP121's WDS configuration the MAC Address of RV180W.Even I tried in WAP121's with and without encryption using the same WPA Key of the RV180W.
The thing is that is not working at all. They work great separately but right WAP121 can't stablish WDS link with RV180W neither do the left WAP121 with RV180W.I tested WDS configuration of WAP121's and they can see each other between them using standard WDS configuration, so I assume that WDS function of WAP121's works great.Finally I try the same config but setting RV180W in WDS Bridge and WDS Repeater without any different result.Do I have any chance to make the topology I showed up would work? How do I have to configure the RV180W and WAP121's?
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
I have this old router and I can't get into the setup. I tried all common passwords and it still won't log me in to the setup screen. The router is an EnGenius NL-5354AP Aries.
View 3 Replies View RelatedI like to create a access point and thinking to buy the Engenius ECB300 or the cheaper ZyXel WAP3205.
I cannot find anything about the power output of the ZyXel WAP3205 so I'm not sure what do buy.
How to make a security key of engenius router wireess
View 1 Replies View RelatedI connected an EnGenius M5000 AP/Bridge to a switch, a Modem (VSAT) is also connect to the switch and aslo my Desktop standalone PC. All instructions were followed to install the EnGenius M5000. However, only the Power,Lan, and Wan light indicators are on but the Link/Signal indicators - red, yellow and green are not coming on.I tried pinging 192.168.1.1 according to the default IP address, but still there was no responds. Even I tried resetting it on the firmware, but it can not ping
View 2 Replies View RelatedI have a laptop running Windows XP that has a wireless card inside.
I have a Single Board Computer (SBC) running Linux that has an 'wireless access point' connected to one of it's Ethernet ports. I want to be able to transfer data between the laptop and the SBC wirelessly (cabling is not an option)
The 'wireless access point' I am using is the EnGenius EOC5611P - it can be configured for:
1. Access Point
2. Client Bridge
3. WDS Bridge
4. Client Router
I don't know which one of these I need,so working that out would be a good start!
i am setting up a network between two houses. I have two Amped Wireless SR300 repeaters and currently I am getting so-so signal strength between the repeaters. To remedy this issue, I purchased two EnGenius EAG-2408 external antenna's.My question is how to calculate how high to mount the antenna. A formula is preferable because I do not know the exact distance off hand and I will have to go out there and measure. I am estimating approximately 75 to 100 yards for the distance. Its flat, with a few trees/brush.
Repeaters:[URL]
-Transmit Power: Up to 20 dBm
-Receiving Sensitivity: -93dBm
Antennas:[URL]
-Omni Directional Antenna
-18 degree vertical beamwidth
I have bought a Engenius wireless adapter because the Verizon FIOS router is in the other room and it is not practical to run an Ethernet cable from my PC. The supplied router is a UltraLine Series 3 9100EM Router, and the wire less adapter model is a EnGenius EUB9801. The signal is fine with every other wireless device inside my place.
View 3 Replies View RelatedI looked around the messages, but could not find anything on this topic. I need assistance with the CISCO WRT54G2 V1. I have an EnGenius EOC5611P (500mW) Repeater set up in my RV and it connects directly to the PC inside my RV using, a CAT 5 connection. I am now using a laptop and would like to connect to the EOC5611P using wireless. "Can I re-configure the WRT54G2 to connect the 5611?" (I would plug the router directly into the 5611). According to EnGenius support, it is possible, but the router would have to be re-configured, but they do not support this setup. I would purchase an EnGenius EAO 7530 which would work perfectly, but the price is $245. Here is the link to the 5611 information [URL]
View 3 Replies View RelatedI have a D-Link DI-624 router and I understand that I can convert this router to a repeater using on line software thus allowing me to extend a wireless signal from up to a 1/4 mile away
View 1 Replies View RelatedI was wondering if it possible to use the DIR-825 as a repeater. My main router is a Airport Extreme but it doesn't reach the whole house. Now what I'm also wondering if I can use the repeater as well as a SharePort for my external hard drive while it is being used as a Repeater.
View 4 Replies View RelatedExtending wireless network range with a repeater HP and Netgear - YouTube my reapter is a old netgear router n150 wondering if its possible.
View 4 Replies View RelatedI have already successfully upgraded the firmware to DD-WRT with no problems.What I want to do is have the D-Link DIR-601 Router set as a Repeater Bridge because I am trying to expand my wireless signal to dead spots in the house.I have NO SECURITY enabled on my NetGear Router and I am still unable to successully setup the D-link DIR-601 Router as a Repeater Bridge.
View 2 Replies View Related