Set up a repeater for their house to get a better signal in locations farther from their main router that is a Verizon Actiontec M1424-WR Rev. C. I am recommending that he get an old router (Linksys wrt54GL or E2000) that I can convert into a repeater with DDWRT firmware as a cheap solution, or with a purpose built Netgear or Linksys range extender repeater as a more $ solution.
View 4 RepliesLooking for setting up the RV180 behind the ActionTec MI424WR-GEN2. At the same time I want to be able to VPN into the network and be able to access objects.
Ideal setup:
Verizon ActionTec modem is primary network (192.168.1.x)
RV180 is secondary network (192.168.2.x)
VPN to 192.168.2.x network from remote locations (client-to-gateway)
I've tried asking from Cisco Support and was given the "we don't suppor that configuration" line. They want me to put it in front of the ActionTec FiOS modem/router in which case then Verizon will provide zero support for anything.Now, to add an extra twist, I do have STBs (Set-Top Boxes) connected to the Verizon FiOS modem/router but nothing special (i.e. no DVR or any stuff like that). How to get this thing up and running so that I can have remote folks VPN into the network? We work with data that needs to remain encrypted during transmission, hence the VPN.I have forwarded ports 443 (TCP), 60443 (TCP), 500 (UDP) and 4500 (UDP) to the WAN IP of the RV180. Network objects behind the RV180 cannot get past the router (it's in router, not gateway mode). The RV180 can ping objects both on the WAN and LAN side, so it seems that the RV180 is the problem child.
How to hook up a seperate wireless router instead of using the fios router. I want to get a n-signal in my house. Would like an answer or a link to another thread.
View 1 Replies View RelatedI tried connecting this on my own and it worked for hard wired Internet service but not for wireless service. Too many cables and boxes attached. I have a vz router, then some other box, and a battery back up.
View 2 Replies View RelatedI have a MI424WR for my Verizon Fios connection. The router is located downstairs, and I don't get Wifi in my bedroom upstairs. Is it possible to connect another WIFI router by ethernet to the MI424WR? Is there anyway where I can do it without the two router's wifi signals fighting each other? Is there a specific kind of router I should be looking for?
View 1 Replies View RelatedI have never setup a GW to GW VPN with a FIOS connection. I have done it with DSL and cable without any problems.
View 1 Replies View RelatedCan't connect DAP-1522 to my Verizon Fios Router
Went through the setup on the DAP-1522. Selected my Verizon FIOS wireless network and entered the WEP key. Everything looks ok on the status page - except Status: Disconnected
Reset/restarted and reconfigured DAP-1522 several times - same result. Can't get it to connect.
So, I bought an E4200 today. I don't know if it's v1 or 2. The box doesn't say v2, so I'm assuming it's v1.
I'm trying to set it up and I have the most recent version of the Mac OS operating system (10.8 Mountain Lion), so the setup CD is not compatible. I'm trying to do a manual set up and it seems that step 1 is to go to 192.168.1.1, which is the same IP that my FIOS router uses, so I go straight there instead of to the E4200.
Has anyone else been able to make this thing work with Mountain Lion and FIOS router?
How do I install a D-Link Wireless router, DIR 655 to the Verizon Fios internet. I have tried different ways but cant get it to work.
View 13 Replies View RelatedI bought the Linksys E1200 for it's wireless N and the guest account. set up my new Linksys E1200 router to use for wireless N access rather that my Verizon Fios provided Actiontec (model M4124-WR Rev.C) which is only wireless G, and so that I can use the guest account. I have an ethernet cable running from one of the 4 ethernet ports on the E1200 to one of the 4 LAN ports on the Actiontec. I have the wireless turned off on the Actiontec, and have the E1200 set as 192.168.1.200.My wireless N signal seems to be working fine from the E1200, and I was able to turn on the guest account on the E1200 and "connect" to it on my iPhone 4, but then when I open Safari I can not connect to the internet.
View 9 Replies View RelatedI'm trying to configure my Linksys WRT54G2 router as my primary router and have my Actiontec just used for the my FIOS TV (eg VOD, widgets, guide). I've googled many HOWTO's on how to do this but I just cant get it working. So setup up will look like this in th end:
(DHCP Server)
(Wireless) (Only TV)
Internet >> WRT54G2 >>> Actiontec >>> PC/Laptops
|
FIOS TV -------------
how to set this up? I understand that the STB devices configured on my Actiontec routers is actually my TV receiver and currently configured with the following IP addresses:
IP-STB1:Connection Type: Coax
192.168.1.100
IP-STB2:Connection Type: Coax
192.168.1.101
IP-STB3:Connection Type: Coax
192.168.1.103
I have COAX Ethernet setup so everything is going through ethernet per Verizon phone tech.
Actiontec Firmware Version: 4.0.16.1.56.0.10.11.6
WRT54G2 = DDWRT firmware
I've tried the following HOWTO's to no avail.[URL]
I connected EA6500 internet port to actiontec router provided by Verizon fios. I don't have any other way to connect as FIOS connection is coax to actiontec modem. I must take a drop from actiontec to internet port on EA6500.
With that said, I can't get EA6500 to work, it keeps saying no internet. The only way I can get it to work is when I set it to bridge mode. This makes my EA6500 a dumb switch/access point. I didn't spend $200 for a switch. I need to use advanced features offered by this router but I can't until this problem is fixed. I made sure I am running latest version of firmware (1.1.28.146856).
I have reset my fios router as well as ea6500 to factory defaults multiple times.
I have Verizon FIOS. I am using their Actiontec router. I turned on WPA2. All is working well. I wanted to turn it off to diagnose a problem with one device. I can see no way to turn it off. To turn it on you click WPA2. you put in an 8 digit "password" etc and it works. There seems to be no way to turn it off. Am I overlooking something? I tried deleting the password. but it gives you an error and remindes you the password needs to be 8 characters.
View 3 Replies View RelatedFor some reason, whenever I go home (I'm in college right now), my internet goes haywire. It'll connect for about an hour or so when I first load it up, but after that, it refuses to connect at all. If I restart my modem (verizon fios modem), then it'll connect for about 5 minutesIf I run the troubleshooter, sometimes it doesn't detect anything wrong with it, and other times, it says "the default gateway is not available"[CODE]
View 1 Replies View Relatedi am using verizon fios. It's pretty fast, in fact I just did a speedtest and here is the result.But I always want more. My laptop has Intel 6300, which supports up to 450Mb. But the Actiontec MI424WR only has 54Mb. It has nice features, but it uses MoCA and connects over coaxial cables, making it unnecessarily harder to use my own router. So I searched online and found tut about how to set the actiontec as a bridge and use your own router.
1) Wouldn't that lower the speed of the router of my choice? Say if I get a 450Mb router, but I need to connect it through the port on the Actiontec, which iirc is only 100Mb. Shouldn't that mean that the new router is forced to operate at only 100Mb max?
2) What is FIOS' top speed? I'm not even sure if it can go up to 450Mb.
3)I have no problems with this Actiontec currently, the only thing I'm looking for is more speed. Has anyone tried calling Verizon and see if they could switch the connection from coax to CAT5?
connecting ASA 5505 with the Action Tech Router?
View 1 Replies View RelatedI have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
I have FIOS and a router provided by verizon. they installed it in the basement and the wi-fi range needs to be improved in my house. I have 2 old linksys routers and a netgear DSL modem/router (with "N") that I'd like to use as an access point or range extender. how do I set this up?
View 1 Replies View RelatedI have a very large house with many people using wireless laptops. i used to have verizon internet and I purchased a wlan 11g mini router from radio lads. After it was set up it worked great. I have just switched to comcast internet (my first mistake) and I can't get the mini router to work.
View 1 Replies View Relatedok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies View RelatedI have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies View RelatedMy house is a little too big for my WRT160N v3 to be able to get to every room, so i was wondering if i could set up my old WRH54G as a repeater to get that extra distance to get those last room on the network? if so how to set up the connection?
View 1 Replies View RelatedI have EA4500 router that connects a couple of desktops in one room. I am having to setup another room for gaming for which I have another EA4500 router. I want to setup the second EA4500 uplink(accesspoint) as the first EA4500. I dont find any interface to do it. I am able to do it wired(by connecting the both the routers through LAN ports). but I dont want to run cable across the house. know if it is possible with another firmware. Or should I return this new EA4500 and buy another router?
View 2 Replies View RelatedI have a lynksys router hard wired and wifi. It is eworking fine when I tried to set up a new Engenius 9550 router as a repeater I can't get the settings correct. I have reset the 9550 twice and still won't reconize the rounter in the home network.proper settings for the 9550.
View 12 Replies View RelatedI want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together. I want to do it all wirelessly if possible.
View 1 Replies View RelatedCurrently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.
The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:
Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater
Below is the link from cisco with explanation. [URL]
Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.
I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?
View 1 Replies View RelatedSetting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.
View 2 Replies View RelatedI am trying to configure repeater mode on an AP, but the authentication is not working.It seems the authentication is seen as EAP-TLS on the ACS 5.2, but im trying to do LEAP.
Relevant config root AP:
!
dot11 ssid Auto3
authentication open eap eap_methods
authentication network-eap eap_methods1
guest-mode
infrastructure-ssid
[code].....
I'm trying to setup a WAP200 as a wireless repeater and I am having some problems. The SSID I am trying to bridge is coming from a WRV210.
I on both devices I have the SSID, security, and channel set the same. The WAP200 is set to Repeater mode and I did a site survey to find the WRV210. The WRV210 is set to to allow the WAP200 repeat its signa using auto select, manual with site survey and manual actually entering the MAC address by hand.
Nothing seems to work. I can see the wireless next work but when i connect to the repeater I never get an IP address.
I have AP1 setup with WPA2-Enterprise. How would I setup AP2 (WAP4410N) to be a repeater for AP1?
View 1 Replies View RelatedI've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
I recently bought one RV180W and two WAP121 in order to make a wireless extension of a network.I configured RV180W as Router and the three of them have the same SSID and password.Also, I added in RV180W WDS configuration both MAC Addreses of WAP121's and in WAP121's WDS configuration the MAC Address of RV180W.Even I tried in WAP121's with and without encryption using the same WPA Key of the RV180W.
The thing is that is not working at all. They work great separately but right WAP121 can't stablish WDS link with RV180W neither do the left WAP121 with RV180W.I tested WDS configuration of WAP121's and they can see each other between them using standard WDS configuration, so I assume that WDS function of WAP121's works great.Finally I try the same config but setting RV180W in WDS Bridge and WDS Repeater without any different result.Do I have any chance to make the topology I showed up would work? How do I have to configure the RV180W and WAP121's?