I have a MI424WR for my Verizon Fios connection. The router is located downstairs, and I don't get Wifi in my bedroom upstairs. Is it possible to connect another WIFI router by ethernet to the MI424WR? Is there anyway where I can do it without the two router's wifi signals fighting each other? Is there a specific kind of router I should be looking for?
View 1 Replies
I'm using a stock FIOS router Actiontec MI424WR, and I'm trying to access the router settings at 192.168.1.1. I type in my username fine, but when I type the password, each keystroke gives me more than one digit. Even holding Ctrl adds one, and letting go removes three characters. I've never seen this happen before, and I've tried it on two computers and three different browsers. I see that people recommend hard-resetting the router, but I was wondering why this has happened
View 3 Replies View RelatedHow to hook up a seperate wireless router instead of using the fios router. I want to get a n-signal in my house. Would like an answer or a link to another thread.
View 1 Replies View RelatedI tried connecting this on my own and it worked for hard wired Internet service but not for wireless service. Too many cables and boxes attached. I have a vz router, then some other box, and a battery back up.
View 2 Replies View RelatedSet up a repeater for their house to get a better signal in locations farther from their main router that is a Verizon Actiontec M1424-WR Rev. C. I am recommending that he get an old router (Linksys wrt54GL or E2000) that I can convert into a repeater with DDWRT firmware as a cheap solution, or with a purpose built Netgear or Linksys range extender repeater as a more $ solution.
View 4 Replies View RelatedI have never setup a GW to GW VPN with a FIOS connection. I have done it with DSL and cable without any problems.
View 1 Replies View RelatedCan't connect DAP-1522 to my Verizon Fios Router
Went through the setup on the DAP-1522. Selected my Verizon FIOS wireless network and entered the WEP key. Everything looks ok on the status page - except Status: Disconnected
Reset/restarted and reconfigured DAP-1522 several times - same result. Can't get it to connect.
So, I bought an E4200 today. I don't know if it's v1 or 2. The box doesn't say v2, so I'm assuming it's v1.
I'm trying to set it up and I have the most recent version of the Mac OS operating system (10.8 Mountain Lion), so the setup CD is not compatible. I'm trying to do a manual set up and it seems that step 1 is to go to 192.168.1.1, which is the same IP that my FIOS router uses, so I go straight there instead of to the E4200.
Has anyone else been able to make this thing work with Mountain Lion and FIOS router?
How do I install a D-Link Wireless router, DIR 655 to the Verizon Fios internet. I have tried different ways but cant get it to work.
View 13 Replies View RelatedI bought the Linksys E1200 for it's wireless N and the guest account. set up my new Linksys E1200 router to use for wireless N access rather that my Verizon Fios provided Actiontec (model M4124-WR Rev.C) which is only wireless G, and so that I can use the guest account. I have an ethernet cable running from one of the 4 ethernet ports on the E1200 to one of the 4 LAN ports on the Actiontec. I have the wireless turned off on the Actiontec, and have the E1200 set as 192.168.1.200.My wireless N signal seems to be working fine from the E1200, and I was able to turn on the guest account on the E1200 and "connect" to it on my iPhone 4, but then when I open Safari I can not connect to the internet.
View 9 Replies View RelatedI'm trying to configure my Linksys WRT54G2 router as my primary router and have my Actiontec just used for the my FIOS TV (eg VOD, widgets, guide). I've googled many HOWTO's on how to do this but I just cant get it working. So setup up will look like this in th end:
(DHCP Server)
(Wireless) (Only TV)
Internet >> WRT54G2 >>> Actiontec >>> PC/Laptops
|
FIOS TV -------------
how to set this up? I understand that the STB devices configured on my Actiontec routers is actually my TV receiver and currently configured with the following IP addresses:
IP-STB1:Connection Type: Coax
192.168.1.100
IP-STB2:Connection Type: Coax
192.168.1.101
IP-STB3:Connection Type: Coax
192.168.1.103
I have COAX Ethernet setup so everything is going through ethernet per Verizon phone tech.
Actiontec Firmware Version: 4.0.16.1.56.0.10.11.6
WRT54G2 = DDWRT firmware
I've tried the following HOWTO's to no avail.[URL]
I connected EA6500 internet port to actiontec router provided by Verizon fios. I don't have any other way to connect as FIOS connection is coax to actiontec modem. I must take a drop from actiontec to internet port on EA6500.
With that said, I can't get EA6500 to work, it keeps saying no internet. The only way I can get it to work is when I set it to bridge mode. This makes my EA6500 a dumb switch/access point. I didn't spend $200 for a switch. I need to use advanced features offered by this router but I can't until this problem is fixed. I made sure I am running latest version of firmware (1.1.28.146856).
I have reset my fios router as well as ea6500 to factory defaults multiple times.
I have Verizon FIOS. I am using their Actiontec router. I turned on WPA2. All is working well. I wanted to turn it off to diagnose a problem with one device. I can see no way to turn it off. To turn it on you click WPA2. you put in an 8 digit "password" etc and it works. There seems to be no way to turn it off. Am I overlooking something? I tried deleting the password. but it gives you an error and remindes you the password needs to be 8 characters.
View 3 Replies View RelatedFor some reason, whenever I go home (I'm in college right now), my internet goes haywire. It'll connect for about an hour or so when I first load it up, but after that, it refuses to connect at all. If I restart my modem (verizon fios modem), then it'll connect for about 5 minutesIf I run the troubleshooter, sometimes it doesn't detect anything wrong with it, and other times, it says "the default gateway is not available"[CODE]
View 1 Replies View RelatedLooking for setting up the RV180 behind the ActionTec MI424WR-GEN2. At the same time I want to be able to VPN into the network and be able to access objects.
Ideal setup:
Verizon ActionTec modem is primary network (192.168.1.x)
RV180 is secondary network (192.168.2.x)
VPN to 192.168.2.x network from remote locations (client-to-gateway)
I've tried asking from Cisco Support and was given the "we don't suppor that configuration" line. They want me to put it in front of the ActionTec FiOS modem/router in which case then Verizon will provide zero support for anything.Now, to add an extra twist, I do have STBs (Set-Top Boxes) connected to the Verizon FiOS modem/router but nothing special (i.e. no DVR or any stuff like that). How to get this thing up and running so that I can have remote folks VPN into the network? We work with data that needs to remain encrypted during transmission, hence the VPN.I have forwarded ports 443 (TCP), 60443 (TCP), 500 (UDP) and 4500 (UDP) to the WAN IP of the RV180. Network objects behind the RV180 cannot get past the router (it's in router, not gateway mode). The RV180 can ping objects both on the WAN and LAN side, so it seems that the RV180 is the problem child.
i am using verizon fios. It's pretty fast, in fact I just did a speedtest and here is the result.But I always want more. My laptop has Intel 6300, which supports up to 450Mb. But the Actiontec MI424WR only has 54Mb. It has nice features, but it uses MoCA and connects over coaxial cables, making it unnecessarily harder to use my own router. So I searched online and found tut about how to set the actiontec as a bridge and use your own router.
1) Wouldn't that lower the speed of the router of my choice? Say if I get a 450Mb router, but I need to connect it through the port on the Actiontec, which iirc is only 100Mb. Shouldn't that mean that the new router is forced to operate at only 100Mb max?
2) What is FIOS' top speed? I'm not even sure if it can go up to 450Mb.
3)I have no problems with this Actiontec currently, the only thing I'm looking for is more speed. Has anyone tried calling Verizon and see if they could switch the connection from coax to CAT5?
connecting ASA 5505 with the Action Tech Router?
View 1 Replies View RelatedI have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
I got Fios installed this week. Router is the Actiontec MI424, it sits int he living room. I ran a speed test of the wifi on my laptop in the living room, and the internet speeds were great. Here's my problem. I'm in a 2 br condo, not a huge place maybe like 1200 Sq feet, same floor. Wifi is awesome in the living room, but in the bedroom it hangs. I still have a signal, varying for low to good, but it takes forever to open a web page, to the point where you can't use the internet. Bedroom is just down the hall.I called Verizon. They told me they can only guarantee the wifi signal 10 feet from the router, after that no promises. My frustration is that with my previous provider, which was giving me a slower internet connection, my wifi in the bedroom was fine and the router was in the exact same spot. Of course I used my own router? I know there are instructions on connecting my old router to the fios one and using my old router for wifi.
View 4 Replies View RelatedHere at work we have a Vigor Modem/Router hosting our connection to the world. It was originally on DHCP & the 4 computers & 2 printers found their own IP addresses without problem.We added a Linksys router via ethernet (to a lan port not the wan) in another area of the yard. This was fine also on DHCP and connecting wirelessly from a laptop or mobile phone was a doddle.Then our oh so wonderful IT geek decided to put the Vigor on a Static IP along with all the computers connected to it. This has some how cut off the wifi capability of the Linksys router now.It is basically acting as a hub for two laptops and nothing else.In simplistic terms with some detail what settings need changing on the Linksys if any?The Vigors internal IP is 192.168.1.1Linksys is 192.168.1.4both on subnet 255.255.255.0I have been advised to set the Linksys to a static IP on the Internet Connection option but what set of figures do i need for that??
View 7 Replies View RelatedI tried to configure my wifi router recently to secure my internet connection. I wanted to add a MAC adress filter, but I had to leave before I could enter them all. I thought that I wouldn't have to enter my own MAC adress since I'm directly connected to the router with a wire, but it looks like I should have entered my MAC adress, because now I can't get access to my router by typing the IP adress, as usual. I tried to reset it, but it doesn't work.
View 2 Replies View RelatedI would like to know if I have wifi connect with my verizon internet.
View 2 Replies View RelatedJust upgraded to Verizon FIOS and had an Actiontec MI424WR Rev F router (firmware v.20.10.7) supplied. Went to white-list my ereader's MAC in router and intitial page asked me to change the default login and password which I planned to do anyway. I know what I changed them to. Made changes, logged out, then decided I really wasn't comfortable with WEP and went back to change it to WPA. All I got was "Login failed, please try again." Finally hit the reset button and started over at the "please change login and password" screen. I can get in then.
I've been through this six times now and cannot get past the initial login without a hard reset. Tried keeping "admin" as the login because I have met peripherials that are touchy about that. Not a major issue now that I have the router set up to my satisfaction, but it frustrates me to not have password access to any part of my system. (Yes, I am that anal.)
I am using Windows 7 on my laptop and trying to connect to my dad's Actiontec M1424WR router wirelessly. It picks up the signal fine, but whenever I try to connect, it takes a while and then just says it can't connect. It will continue to try and connect, only ever getting as far as limited access then quickly losing the connection, all with a Good signal. My dad and brothers all use Windows 7 laptops as well and they are and have been connected just fine. We tried a wired connection and that works perfectly too, so the only problem is getting it to work wirelessly now.
View 1 Replies View RelatedI am moving into an apartment thereafter. I have an HTPC in use, a personal computer for gaming/processing, and my fiancee has an Apple Macbook Pro that she uses quite often. I have an HDHomeRun Dual (2 tuners) for streaming OTA/QSM cable over the network (the HDHomeRun plugs into the network, not a computer). I also have a TV and Blu-Ray player that have ethernet ports.
Currently I use Verizon Fios and their Actiontec MI424WR router, which to my knowledge has gigabet ethernet. When I move I will probably be saddled with Comcast Xfinity Internet, which will supply a cable modem if I want, but no router. The only router I currently own is a Zyxel NBG-419N, which has only 100/10 ethernet ports. My current computers all have gigabit ethernet. For the home theatre components and my HTPC, I plan to pick up a network switch with gigabit ethernet. So my questions are:
1. If I use the Zyxel and the Comcast cable modem, would I be throttling my network speed at the router? I would hate to choke my speed just because one component does not have gigabit ethernet.
2. If I were to upgrade to, say, an Asus RT-N56U, would that make a huge difference on network browsing and throughput speeds?
3. Finally, what kind of cable is needed to maximize discernible speed increase? Cat5, Cat5e, or Cat6?
what is the set up procedure for adding a printer with wifi capabilities?
View 1 Replies View RelatedI have that red gigabit router with the 150/65 service. It connects via ethernet for internet and has a coax to transmit the guide data etc.So my idea was to just leave the Verizon router connected and on (with wi-fi off) so it could do the TV stuff and just plug my router into the ethernet wall port the Verizon guy installed.Not so easy of course, my E4200 will not recognize the ethernet from my ONT (I think that's what the device they put in my basement is called) and the internet doesn't work. I have factory reset the router.The reason I am doing all this is because the wireless range of the e4200 at 2.4ghz is near unmatched and given my house, the actiontech cannot reach my room.
View 9 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedIm having problems staying connected to my internet. I have Verizon Fios router that is wired into this desktop i also have 2 laptops and now im trying to connect a second desktop wirelessly to the router. My Netgear Rangemax PCI picks up the signal at 68% and connects to the router. But periodically it disconnects from the router and i click connect to a network icon and it shows that i have no wireless internet as if no PCI card is installed so i wait a min then it shows up again and windows network diagnostic kicks in and "resets the network adapter" and all is well for about 15min till it disconnects again.
View 1 Replies View RelatedMy macbook is able to detect my router, but the router cannot connect to the internet. I was wondering if the E1200 requires a modem, where as FIOS only offers ONT?
View 1 Replies View RelatedI'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
I recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150
Just had Verizon FIOS service installed. It comes with an actiontec modem. I would like to remove the actiontec modem and connect directly to my Linksys RT31P2 which is cascaded to my Linksys WRT54G. I have tried just about every router setup config; all with no success. How to be able to connect the FIOS directly to a linksys router.
View 3 Replies View Related
