I am trying to setup D-Link DAP-1360 as a range extender, but am unable to see the device from my browser. The IP address is given to be 192.168.0.50. My router IP address is 192.168.1.1 and my PC IP address is 192.168.1.34.
View 11 RepliesI am trying to extend range of my DIR-615 with a DAP-1360. Part of the installation requires pulling up 192.168.0.50 on my brouser. But it won't pull up.
View 1 Replies View RelatedI want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together. I want to do it all wirelessly if possible.
View 1 Replies View RelatedI got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I have a wireless schedule setup on my DIR-655. Works great. Now I would like to run different hours on different days. Have wireless up on certain hours during the week, different hours on weekends.
How do I set up a schedule to one one set of hours during the week, and a different set of hours during the weekend?
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version :
ISP : Be Internet
I have a router supplied by my ISP which is effectively locked down, the wireless on that router give me a massive 35 Mbps (yes i know... awesome) so I wanted to get something that would allow me to stream movies wirelessly in the house. The setup I had before was Thompson DSL router downstairs (ISP router) running the DSL connection and Wireless, a TP-Link 200Mbps Power over Ethernet connecting upstairs to a Netgear ADSL Wireless router (somewhat flaky device). This router had DHCP disabled and a static IP address, I had configured wireless with the same SSID, password and channel as the ISP router and they were all happy and everything was working (most of the time except when the netgear would crash or the 35MB wifi was too slow to achieve what I wanted).
What I would like to do is this... ISP router downstairs with wifi disabled so it just handles DHCP and DSL connection, router upstairs (New TP-Link) running new WiFi, DHCP disabled (static IP address for Router) but connected to router downstairs through TP-Link Power over Ethernet.
I was hoping it was as simple as the Netgear router where disabling DHCP was enough for it to see the other router and just work but it isn't doing that
I can ping the ISP router but cannot get to the internet,
Region : Portugal
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
set up my router. Trying to set up my 3G modem with TP-Link MR3020.
Tried troubleshooting to find out where it went wrong and just couldn't figure out. Just tried disabling the wireless security and *poof* I'm able to connect to the Internet. Right after setting up the Network Key, I can't connect to the Intertnet via my router.
Here are the datas.
Windows IP Configuration
Host Name . . . . . . . . . . . . : TOSHIBAM840
Primary Dns Suffix . . . . . . . :
[Code].....
Region : Ireland
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 1.0.0 Build 111125 Rel.28195
ISP : Eircom
I'm trying to set up external Wake On Lan with my TP Link router.
I can get it working internally using the mac address I'm just wondering how do I do it remotely?
Region : Argentina
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Region : Australia
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 110620 Rel.52053n
ISP : Amnet
I want to setup this modem wirelessly such that:
- Wireless User A has full unrestricted wireless access (to Internet and all other services) and
- Wireless User B has no internet access but access to file sharing and related services.
Can this be done and how can it be done?
I have an old D-Link DIR-615 wireless N router that I am trying to re-purpose as a wireless bridge so I have network access in the back part of the house where I can't run ethernet wires.
I successfully installed installed DD-WRT on the D-Link and thought I had configured the D-Link into a wireless bridge; however, the D-Link just does not want to communicate with my primary Zoom Cable Modem / Wireless Router. Pings between the two devices return nothing. I disabled all security, they are on the same subnet (192.168.0.1 and 192.168.0.6 for the D-Link), same SSID, etc.
I attached a word doc with screen shots of the settings on both devices.
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a client that has a WR2543ND (House) and WDR4300 (Office/Internet) router that are located in two separate buildings about 40ft apart. He has each one hooked up to external antennas connected on the outside of the buildings. Back in December I got WDS working between the two routers and the PC in the house was able to use the Internet in the Office as well as share resources between the office and house computers. Two days ago I was down there working on his network and I was having problems setting up network shares. I discovered I wasn't able to ping from the Office PC to the House PC or vice versa and what's even stranger, I couldn't ping the House PC from the House Router (WR2543ND). I checked WDS status and on the House Router is says "Run" but on the Office Router it says "Int" but the WDS is definitely up because I am able to ping from the Office Router to the House Router, plus I am able to use TeamViewer to connect to the House computer from the Office computer. There are no firewalls enabled on Windows. Lastly the DHCP server is only running on the Office Router.
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
I have just started using my D-Link 1310 Router after quite a few years of it laying around. I managed to get as far as connecting my D820 and my Desktop in a basic Network. I have Windows XP Home on both the Desktop and Laptop. The next step I want to accomplish is making the Laptop wireless with my apartment. When I first had the Router, I of course had Technical Support and my Warranty with Dell was still active, so I was walked through the process and took notes. The only file I made note of for this step was installing the driver (US) WLAN Card Rev.A12, but there must be something else that enables the WiFi catcher because I don't have any icon in the System Tray and no way to access it.
I also remember it being necessary to Bridge the Modem and Router, (I believe we did it from the Verizon site). Though I was told recently that Bridging is not used anymore, now they do a thing called "Double Netting"?
i press and hold and still red link on the throughput LED.
it says 303 and 302.........
[URL]
Want to set up my DIR-825 with FW ver. 1.13NA for vpn, how to set it up.and if you know a good link for set up routing and remote access from windows 2008 r2 64bit.
View 5 Replies View RelatedI'm running a Mac OS X Server on my network. I'd like to use the Server's DNS instead of my ISP's. In the D-Link Router I've set the DNS to the OSX server in the WAN section. Unfortunately it doesn't allow my clients on the network to connect to the internet when I do this.
If I set the DNS on the client to the OS X server it works fine. Or if I set the DNS on the router to my ISP's (or Google's) it works fine too.
Is this a route configuration issue? (And if so, what can I do to fix it?) Or is this an OS X Server issue?
I dont know if there is a way to set up donwload limits per I.P. address on my home network.
View 3 Replies View RelatedI have been trying to setup my DIR-655 A4 (Firmware 1.34NA) router to send me email notifications on new firmwares, when the log is full and every Saturday. So I have a schedule already created for sending the emails on Saturday and I also have the option to send notification of new firmware checked. Now I have settings, similar to the following, under email settings.
View 14 Replies View RelatedConfigured a D-Link DIR-601 router? The internet is connected, but there is a yellow triangle with a exclamation mark on the bottom right corner stating it isn't connected. I read the manual and did everything as listed, but still have the same issue.
View 4 Replies View RelatedI have read the sticky about the Game fuel, and i have tried resetting everything, static IP address, all the info i have found on line. i still i keep getting booted when i join a game, or most of the time i cannot join a party. No matter what changes I make it gets worse than factory setting. i have read for hours on different ways to set up the router and what not. i have changed settings on the PS3, router and still getting nowhere.so can some one pls tell me how to set this thing up before i use it as anger management.?i know how to access the router page . but i don't get the setting up port forwarding.
View 10 Replies View Relatedsetting up the email notifications. I need the log emailed to me during a certain time of the day and it wont email anything. Even when I am in the log and push the email now, it does nothing. I've tried setting it up through hotmail, lmsn live, and gmail. None of them work. What am I doing wrong or what do I need to do?
View 9 Replies View RelatedMy router was working just fine when a lightning struck. I cant seem to connect to the router's configuration page (192.168.1.1) anymore, All the lights on the router are on and I tried to reset it to default settings several times but still it wont connect. I tried it on a laptop but I still cant get it to connect. I can surf the net just fine when using the ADSL modem though. I can ping the IPaddress 192.168.1.100 but can't ping the default gateway which is 192.168.1.1. I also tried switching to another cable just in case but to no avail.
Here are some info:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMiko Luis>ipconfig/all
[Code].....
I need setting my 825 router on the best optimize setting for my ps3, Im running wireless on it and the router is about one room away from my ps3 which isnt that big of a difference since I am getting 95-100% signal on it, the issue is the rate speed runs about 36m-54m it NEVER, or at least I havent seen it go higher than that.I turned the QO6 engine but it didnt really change a thing, will running this wire do the majic? or is there another alternative set up I can do on the router to have it run on best settings.
View 1 Replies View RelatedI just acquired an Ipod Touch and am trying to set it up to connect to my exisintin DIR-615 router. It is about one year old, but I have misplaced all the info I had on it, including any password info. Trying to use the blue lit button on the right side of the router does not allow access to the Ipod, nor my daughter's Apple computer.
Are there changes I need to make or special procedures for Apple products?
Using DIR-601 hardware version B1, Firmware 2.00NA, I am debugging problems I've had with this router, so it is set up on my network so I can access it from both the WAN and LAN side. If I ping the router from the WAN side, I get a very fast response. But when I disable ping from the administrative tools from the LAN side and reboot the router, I still get responses to my ping! I know the router is responding because if I disconnect the WAN cable from the router (connected to "INTERNET", the pings stop. So the router is ignoring user settings at Advanced->Advanced Network->WAN PING! Looks like a firmware bug.
View 3 Replies View RelatedI have a DCS-930L network camera that I configured from its Web-based interface. In SETUP | Network Setup, I have disabled both UPnP and UPnP Port Forwarding. In my router's (Netgear WNDR3700) settings, I reserved the local IP address, 192.168.1.80, for the DCS-930L. In the DCS-930L I assigned the network camera HTTP Port 8000; therefore, I can access the DCS-930L on the LAN from [url].... In addition, in the router, I have forwarded port 8000 to the local IP address, 192.168.1.80, so I can access the DCS-930L from outside the LAN.I can access the DCS-930L both from within the LAN and outside of the LAN.
However, even though UPnP and UPnP Port Forwarding in the DCS-930L are disabled, the DCS-930L keeps adding and deleting UPnP NAT rules in the router. In addition, a system at the IP address, 207.232.83.172, keeps attempting to access the DCS-930L from different ports. I traced the IP address, 207.232.83.172, to the ISP, Telekenex, in Los Angeles, California. A partial log from the router is below.[code]...
Attempting to connect my iPod to the wireless network. The SSID is set to visible and the ipod finds the network. I set the ipod to the security type of the router and have verified the security key. When I attempt to connect I get a message that says unable to connect to the network.
View 8 Replies View Relatedi have a WD My Book Live and it's connected to my DIR-825. i'd like to configure the router to allow FTP access to the NAS from the internet. the drive has an option to enable FTP in it's configuration, but i have not done this before and i don't know what to do to create a solid/secure FTP portal so that i can access my files remotely.how do i configure the router for this ? my router is set to DHCP and i have turned MAC filtering on.. in particular i am looking for the ability to transfer/copy files from the drive, and not allow any modification/writing to the drive from the outside.
View 10 Replies View RelatedI bought a DIR-655 today so i can port trigger to all my xbox's instead of only being able to port forward to 1 xbox from my Netgear CGD24N. My problem is setting up a stable network that wont drop out.
What i am trying to set up: Internet --> Modem (Netgear CGD24N) <---> Router <---> Everything else (2 Xbox's, 5 Computers, Phone's)
I have one ethernet cord from my netgear to the internet port in my D-Link. Is that correct?
They are both set to DHCP as that is the only way i have been able to create a network that i can connect to the net through my router. Problem is it is constantly reconnecting and only getting speeds of 2mb dl and 1mb up. (I should be getting speeds of 30mb dl, 2mb up.)
I have a desktop pc and bought the DIR-601 so I could use my IPod touch. Everything works good but I think one or two other people ,possibly neighbors are using my wifi. Today I used my iPod and checked under general settings and noticed a wireless name I did not set up but then it disappeared. Also on dlink account online a few months back I was trying to do something with account, security and noticed one or two connections I didn't set up. What are the steps securing router,wifi so others cannot access or use ?
View 1 Replies View Relatedsetting up wifi network in my office. my complete set up right now. the main problem is how to setup my access points . Okay so here it is.
I have 3 - 4 PCS in my office out of which My machine is the main machine and everything is setup on this. so for networking what i have done is i am using a TP link router model TL-WR941D. i had got it configured from an engineer. A cable from my internet modem goes into the blue port of this router(WAN) and my PCs are connected via the LAN port of the router . so everything is working fine right now the local network and internet on all PCS and my laptop also connects through the wifi and is able to access other pcs and also the internet.
To have better signal strength on other floors of the building my engineer had installed 2 access points. They are TP link model Tl-WA901ND. yesterday i updated the firmware of my main router and the settings were some how lost but i managed to set it back to working state using the quick setup utility. so my router and wifi is working fine. But now my access points have stopped sworking . i mean i am not able to get better signal strengths thorugh them. i am assuming theirs ettings /ip etc are lost. now i have no idea how to setup these access points to be used again as part of my wifi network. I looked on the internet but nowhere the thing has been explained in detail. how can i configure my access points/repeaters agaain? i am stuck and engineer is not available for nest few days and my officee internet is suffering.