My router was working just fine when a lightning struck. I cant seem to connect to the router's configuration page (192.168.1.1) anymore, All the lights on the router are on and I tried to reset it to default settings several times but still it wont connect. I tried it on a laptop but I still cant get it to connect. I can surf the net just fine when using the ADSL modem though. I can ping the IPaddress 192.168.1.100 but can't ping the default gateway which is 192.168.1.1. I also tried switching to another cable just in case but to no avail.
Here are some info:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
I got a new TP-Link WR740N router and I'm having a problem with it. Everytime I enable security (WEP, WPA etc.) the signal on all notebooks will go "local access only" immediately, even if I use the right password. Router signal is always there, but Internet access will only be available if security is set to "unprotected" on the router setup. Funny thing is that my old router (Linksys WRT54) had WPA2 on and everything was ok.
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : Others Model : TL-WR740N Hardware Version : Not Clear Firmware Version : ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others Model : TL-WR740N Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
I've been having this issue for quite some time on my Windows 7 SP3 x64 machine. It's a desktop, connected via ethernet to a TP-Link WR740N router, that also provides wireless coverage. My ISP is a local one (the country is Latvia), and it offers a decent 100 MBps up/down optical fiber internet service. Now for the problem - there is only one home network on my computer, that seems to work, and that is 'Network 2'. Whenever I have to reboot the router for whatever reason, it attempts to reconnect, but sometimes reconnects to a 'Network 3' and once even to a 'Network 4' and 'Network 5'. None of these other networks have internet access. I tried to run the diagnostics tool on the issue, and usually it told me that there's a problem with the default gateway. Additionally, twice I've had the issue of the computer completely freezing when connected to one of the Internet-less networks (eg 'Network 3'), and trying to disable the network adapter, forcing a restart that consequently caused a fail boot - from there on I had to use System Restore to actually get my PC to function.
The way I've been fixing it, apart from random rebooting, reconnecting, and hoping for the best (that it decides it wants 'Network 2'), is by putting in the Resource Mini CD that came with my router, and running the Wizard for the WR740N router. It has 4 steps, the 2nd of which is 'Installing the router' (configuring the network adapter), at which point, my internet starts to work (always connects to 'Network 2'). If, I however, decide to continue this process to the step 'Configure router', and attempt to set up my wireless connection, it will begin to reset itself, and once again connect to 'Network 3', leaving me without internet access.
Region : UnitedStates Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.1 ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : Philippines Model : TL-WR740N Hardware Version : V4 Firmware Version : 120320 ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
Region : Others Model : TL-WR740N Hardware Version : Not Clear
I seted up router and i coud acces the utility window, then i switced from w7x32 to w7x64 and then i try to acces the utility window i can only see.Username or Password is incorrect.Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". The settings will be restored to factory default after the resetting.
How to restore the device to the factory default settings?Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings.no pop up window appears i tried looking this up and the closest thing i found was to un-check the proxy but its not checked so what should i do to be able to access utility window?
Region : India Model : TL-WR740N Hardware Version : Not Clear ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I just acquired an Ipod Touch and am trying to set it up to connect to my exisintin DIR-615 router. It is about one year old, but I have misplaced all the info I had on it, including any password info. Trying to use the blue lit button on the right side of the router does not allow access to the Ipod, nor my daughter's Apple computer.
Are there changes I need to make or special procedures for Apple products?
setting up wifi network in my office. my complete set up right now. the main problem is how to setup my access points . Okay so here it is.
I have 3 - 4 PCS in my office out of which My machine is the main machine and everything is setup on this. so for networking what i have done is i am using a TP link router model TL-WR941D. i had got it configured from an engineer. A cable from my internet modem goes into the blue port of this router(WAN) and my PCs are connected via the LAN port of the router . so everything is working fine right now the local network and internet on all PCS and my laptop also connects through the wifi and is able to access other pcs and also the internet.
To have better signal strength on other floors of the building my engineer had installed 2 access points. They are TP link model Tl-WA901ND. yesterday i updated the firmware of my main router and the settings were some how lost but i managed to set it back to working state using the quick setup utility. so my router and wifi is working fine. But now my access points have stopped sworking . i mean i am not able to get better signal strengths thorugh them. i am assuming theirs ettings /ip etc are lost. now i have no idea how to setup these access points to be used again as part of my wifi network. I looked on the internet but nowhere the thing has been explained in detail. how can i configure my access points/repeaters agaain? i am stuck and engineer is not available for nest few days and my officee internet is suffering.
The wireless is just beyond my computer's ability to detect. I have a D-Link WBR 1310 Router hooked up to a high gain wireless antenna-yes, clear line of sight. I have no direct access to our community modem or ISP.
Region : India Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
I have a TP-Link TD-8616 modem and TP-Link TL-WR740N wireless router. Both are ADSL compatible. Each time I tried to connect with the wireless router I will no longer have internet service. Teksavvy is my internet provider. how I can get this to work.
Region : Others Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
Region : USA Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : ISP : Region : UnitedStates Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : 3.16.5 Build 130322 Rel.59120n ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
Region : Sweden Model : TL-WR740N Hardware Version : V4.20.0
I have a TL-WR740N. If router is on and I turn on my laptop it will not automatically connect to the router. I must turn off the router and then turn on again to get connection to the Laptop. I think I have missed something in configuration of the Laptop.
Region : Argentina Model : TL-WR740N Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
I have a weird problem. I bought recently a new router, and when I try to connect to the settings on it on http://184.108.40.206 it sometimes works, mostly doesn't. When I ping other devices which are connected it, it's the same; sometimes get a response, mostly I don't. The router model is: TP-LINK 150Mbps Wireless N Router TL-WR740N, The thing which it's connected to is entitled "ADSL2+ Ethernet bridge router" That aforementioned thing is suppoused to be a modem. But, when I try to connect to its settings from http://10.0.0.138 , I'm able to, and other who are connected to the network give response to a ping.
Region : Others Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.12.11 Build 120320 Rel.51047n ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx 783/31/2013 17:04PPPINFOsent [LCP ProtRej] 793/31/2013 17:04PPPWARNINGPPPoE link down
I've been trying to configure a TP-Link L-WR740N to act as an access point using the instructions here as a guide. As stated in the guide, I've been changing the IP address of the TP-Link router to a new address that lies outwith the pool of available DHCP addresses in my combined modem/router but with less than resounding success. After rebooting the TP-Link router, I am unable to access the set-up interface - the newly allocated IP address doesn't work, neither does the original IP address work. What is happening here? If I change the IP address to one that lies within the DHCP pool and reboot, I can access it ok with the new address. However, that obviously clashes with the set-up instructions.
Region : Hungary Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
i have a WD My Book Live and it's connected to my DIR-825. i'd like to configure the router to allow FTP access to the NAS from the internet. the drive has an option to enable FTP in it's configuration, but i have not done this before and i don't know what to do to create a solid/secure FTP portal so that i can access my files remotely.how do i configure the router for this ? my router is set to DHCP and i have turned MAC filtering on.. in particular i am looking for the ability to transfer/copy files from the drive, and not allow any modification/writing to the drive from the outside.
I have a desktop pc and bought the DIR-601 so I could use my IPod touch. Everything works good but I think one or two other people ,possibly neighbors are using my wifi. Today I used my iPod and checked under general settings and noticed a wireless name I did not set up but then it disappeared. Also on dlink account online a few months back I was trying to do something with account, security and noticed one or two connections I didn't set up. What are the steps securing router,wifi so others cannot access or use ?
All I can tell you about my internet connection is that I have a kinda white box looking antenna, which is connected by a rj45 to this ghetto looking modem thingy - imgur: the simple image sharer (the other cable obviously gets plugged in the computer).it is not a mac adress thing, cause I can plug that cable in any pc I want and it is going to get an ip through DCHP in a matter of seconds. [code] Friend of mine connected another pc to this internet some time ago using somekind of wan bridge/lan bridge option on his asus router, but I can't find anything equivalent on mine. Had the exact same issue when trying to connect the router by conventional means.
during the first set up I have set a password as it was requested during the installation routine. After the installation, I added the camera's IP to my browser (tried IE9 and FF). In both cases I was asked to enter the user name and the PW, but I can't access the 930. I'm using the very same PW as I had set up during the routine, but none of the browsers accepts the PW.
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
Region : UnitedKingdom Model : TL-WR740N Hardware Version : V3 Firmware Version : not sure ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.