I have a TP-Link TD-8616 modem and TP-Link TL-WR740N wireless router. Both are ADSL compatible. Each time I tried to connect with the wireless router I will no longer have internet service. Teksavvy is my internet provider. how I can get this to work.
View 3 RepliesRegion : Sweden
Model : TL-WR740N
Hardware Version : V4.20.0
I have a TL-WR740N. If router is on and I turn on my laptop it will not automatically connect to the router. I must turn off the router and then turn on again to get connection to the Laptop. I think I have missed something in configuration of the Laptop.
I have a weird problem. I bought recently a new router, and when I try to connect to the settings on it on http://198.168.0.1 it sometimes works, mostly doesn't. When I ping other devices which are connected it, it's the same; sometimes get a response, mostly I don't. The router model is: TP-LINK 150Mbps Wireless N Router TL-WR740N, The thing which it's connected to is entitled "ADSL2+ Ethernet bridge router" That aforementioned thing is suppoused to be a modem. But, when I try to connect to its settings from http://10.0.0.138 , I'm able to, and other who are connected to the network give response to a ping.
View 4 Replies View RelatedRegion : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : I am trying to set up my router for about 2 days without any effect.
Here you can find, what I have to do to connect through Ethernet cable to the internet at our university:[url]....
When I set auto-detect IP on router, it says that I have Static IP. In CMD I can find out all the information about the connection and the licence is usually for one day (automatically renewing). I've also tried to clone MAC address, nothing happened.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :
I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
I am facing some issue in LAN network.I have connected one desktop( win 7) and another desktop (win xp) to the TP link router. Both the computers got ip address and able to share the internet. But both the computers are not in the same network. That is they cant PING each other. hence they are not visible to each other.
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
Region : Others
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
Region : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version :
Firmware Version : 120320
ISP : connect communication
HOW CAN I BLOCK USER FROM MY ROUTER WHO USES WIRELESS WITHOUT CHANGING PASS BECAUSE I WANT HIM TO KNOW PASSWORD BUT HE COULD NOT CONNECT
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx
783/31/2013 17:04PPPINFOsent [LCP ProtRej]
793/31/2013 17:04PPPWARNINGPPPoE link down
[Code].....
Region : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies View RelatedI've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
My router was working just fine when a lightning struck. I cant seem to connect to the router's configuration page (192.168.1.1) anymore, All the lights on the router are on and I tried to reset it to default settings several times but still it wont connect. I tried it on a laptop but I still cant get it to connect. I can surf the net just fine when using the ADSL modem though. I can ping the IPaddress 192.168.1.100 but can't ping the default gateway which is 192.168.1.1. I also tried switching to another cable just in case but to no avail.
Here are some info:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMiko Luis>ipconfig/all
[Code].....
I got a new TP-Link WR740N router and I'm having a problem with it. Everytime I enable security (WEP, WPA etc.) the signal on all notebooks will go "local access only" immediately, even if I use the right password. Router signal is always there, but Internet access will only be available if security is set to "unprotected" on the router setup. Funny thing is that my old router (Linksys WRT54) had WPA2 on and everything was ok.
View 4 Replies View RelatedI just got a TL- WR740N router and somehow managed to configure it using my girlfriends Acer Aspire One Happy netbook.The internet works fine when the netbook is connected to the router via cable but it can't connect wirelessly to the network I have created. At first some massege appeared saying that there are 2 identical IP's and there is a conflict or something like that. Now it just stops trying to connect to the network. I can connect with my own laptop tho.
View 3 Replies View RelatedI've been having this issue for quite some time on my Windows 7 SP3 x64 machine. It's a desktop, connected via ethernet to a TP-Link WR740N router, that also provides wireless coverage. My ISP is a local one (the country is Latvia), and it offers a decent 100 MBps up/down optical fiber internet service. Now for the problem - there is only one home network on my computer, that seems to work, and that is 'Network 2'. Whenever I have to reboot the router for whatever reason, it attempts to reconnect, but sometimes reconnects to a 'Network 3' and once even to a 'Network 4' and 'Network 5'. None of these other networks have internet access. I tried to run the diagnostics tool on the issue, and usually it told me that there's a problem with the default gateway. Additionally, twice I've had the issue of the computer completely freezing when connected to one of the Internet-less networks (eg 'Network 3'), and trying to disable the network adapter, forcing a restart that consequently caused a fail boot - from there on I had to use System Restore to actually get my PC to function.
The way I've been fixing it, apart from random rebooting, reconnecting, and hoping for the best (that it decides it wants 'Network 2'), is by putting in the Resource Mini CD that came with my router, and running the Wizard for the WR740N router. It has 4 steps, the 2nd of which is 'Installing the router' (configuring the network adapter), at which point, my internet starts to work (always connects to 'Network 2'). If, I however, decide to continue this process to the step 'Configure router', and attempt to set up my wireless connection, it will begin to reset itself, and once again connect to 'Network 3', leaving me without internet access.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
I ordered the D-link DIR-815 router online at [URL], and I'll be receiving it this Monday which is the 14th, so I am asking my questions on here now, so I could be prepared.
1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? First before I forget, I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet on my phone, and use WiFi only on my phone, how would this work?
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
wan led on my router is not illuminating. My internet connection is fine.I have pppoe connection. What may be the reason ?
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to change my router password?
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
Region : Vietnam
Model : TD-W8151N
Hardware Version : V1
Firmware Version :
ISP :
I'm using a Tp-Link's Product (TD-W8151N). But now, i want to using TL-Wr740N repeat the Wifi from TD-W8151N. How can i do that?
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
i m experiencing wireless disconnects every 5 or 10 minutes and all i have to do is too disconnect from the router in windows from Wireless connections panel , and reconnect and it ggets fixed for some time again . i got so frustrated that i changed to openwrt , the disconnection problem is gone but not getting the 150Mbps.