Am trying to connect 3 pcs connected to a Dlink 8 port switch through a Dlink WL2100 Access point connected as an AP Client to the main network. Only 1 pc is able to see the main network and am having none of the other 2pcs are able to see the main network. The 3 pcs are able to see each other.
View 1 Replies
How can i configure my wireless AP to provide wireless internet to my network via my switch?
View 2 Replies View Relatedi am trying to configure my HP 420 access point. I have configure different SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.
in the following the output of show run int in cisco 4500 switch:
interface GigabitEthernet3/13
description ==== HP ACCess point ====
switchport trunk allowed vlan 99,130,132
switchport mode trunk
[code]....
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
I am having a problem setting up an Access Point. Here is my configuration. I have a Comcast Cable Modem that plugs in to a 24 port Netgear Switch. From the switch it plugs into a Linksys N wireless router with an IP of 10.1.10.76. I don't know the linksys model. But it is fairly new. I also have a Netgear WN604 N Access Point that plugs in to the same switch in another location away from the wireless router about 75+ft.
I configured the access point's IP to be 10.1.10.130 with DHCP off and DNS as 10.1.10.1. The cable modems default Gateway is 10.1.10.1 and it handles the dhcp which is provided to the switch were both the wireless router and access point get there IP's. I can't set it up so that the cable modem plugs in to the wireless router first then the switch because of a security system that is setup to the Comcast Cable Modem.
My Goal is to the the same identical SSID and Password for both the Linksys and Access point. I don't think I can set it up as a repeater because it's to far away from the linksys router.
I am staying with some family for the next two months and they don't have wireless internet at their house. When they bought their house it was wired for ethernet and have the modem going to a netgear 8 port switch which is going to the different rooms of the house. I would like to add a wireless access point to one of those 8 ports coming from the switch. I currently have a TP-LINK TLWR740N router that I can configure into an access point, or I can buy just and access point. Unfortunately it is not an option for me to plug the modem into the router and then the router into the switch.
View 1 Replies View RelatedI think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
View 4 Replies View RelatedHere is my set up:
192.168.1.1 is a Linksys WRT610N acting as a router and DHCP server for addresses .100 to .150
192.168.1.2 is TEW-639 with DHCP turned off and connected to the Lynksys via one of the LAN ports.
I then have a FosCam camera with IP 192.168.1.010, connected either wirelessly or via a wire on a LAN port to the TEW-639W.
Here is my problem: If the FosCam is connected wirelessly to the TEW-639W I am unable to see it from any device connected to the Linksys. If I connect the FosCam via a wire to a LAN port on the TEW-639W then I can see it from a device connected to the Linksys device.If a device is connected to the network via the TEW-639, I can see the FosCam whether it is hardwired or wirelessly connected to the TEW-639. What am I doing wrong?Why can I not see the wireless connections on the TEW-639 from a Linksys connected device?,The setup is that the internet comes in and is connected to the Linksys, which then via LAN cable and LAN ports on both devices is connected to the TEW-639, which is then connected to the camera.
I need to setup my Netgear as a switch/access point. I need the following set-up. My ipconfig /all reports:
View 27 Replies View RelatedI'm using 4 wap200 cisco AP, 1 wap200e linksys AP and 1 cisco sf300-24p switch. Every AP has 2 SSIDs,one is for clients and one for mobile devices.I have updated the equipment to the latest firmware but I still encounter the same issue. The mobile devices go through APs and once every 2 days, my wap200e blocks its lan interface. I suspected a stp issue, because the switch was seeing MAC addresses coming from different ports.So I disabled STP on the switch and on the AP. The annoying thing thing is that none of my other antennas get cut off.I tried replacing it with a cisco wap200e,same issue.
View 1 Replies View RelatedI have a Cisco 2811 router with C288nm-advsecuruityk9-mz.151-4-4.M.bin IOS version.The router has two LAN interface FE 0/0 and FE 0/1.The router have too, two interfaces ADSL ATM0.0.0 and ATM 0.0.1, both are connect to internet..I need the next configuration.The interface FE 0/0 is directly connect to a Switch A.The interface FE 0/1 is directly connect to a Access Point Cisco.The Access Point and the Switch is not connecting between.The subnet of Switch A and AP are different (Switch A 192.168.180.0/24 and AP 192.168.181.0/24)The devices in the switch A have dynamic IP address, the router must be a DHCP pool to assign theses IP.The device in the AP have dynamic IP address, the router must be a DHCP pool to assign theses IP.I created two DHCP pools in the router, one for the subnet 192.168.180.0 and other for 192.168.181.0, but the devices of FE 0/0 assign IP of 192.168.180.0 or 192.168.181. 0, but not only in the 192.168.180.0.
View 5 Replies View RelatedI would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?
View 3 Replies View Relatedwe got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?
View 2 Replies View Relatedi have 2 cisco 1522 series out door LAP connected to a 3560 POE switch which is not powering up, while ordering my dealer told that it will work with POE, and its go live stage, is there any way to upgrade switch with any IOS version where i can get enough power for 1522?
View 4 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedUsing a Cisco router as an access point on a separate floor. Was connected and doing work on my laptop when the connection drops. It now says that I am unable to connect to that access point, I am still able to connect to all other wifi signals available. My phone and tablet can still connect to that access point without any problem, but no go for my laptop. Wired connection works on laptop, but for wifi it just keeps saying Windows was unable to connect.
View 1 Replies View RelatedI currently have a network setup like this:
Route 1 --> Switch --> Access Points ---> Router2 connected to one of the access point
So pretty much I'm trying to create a wireless network for a temple. I set up a network with several access points as above. However, they wanted a network for the office separate from the rest of the temple. So I decided to setup Router2 and connect it to one of the LAN ports of an access point.
However, this seems messing up the whole network. People can connect to the access points but they won't have access to the Internet. Also, if I connect my laptop to the office network, I wouldn't see the gateway as 192.168.1.1, which was set for Router2. Instead, I always saw the IP address of Router1 as the gateway.
How to connect a router to access point
View 1 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedTried to connect a second Edimax AP to my home network configured as repeater. Keep getting random errors. Each of them have a different IP address
View 11 Replies View RelatedHow we connect two different access point to each other
View 1 Replies View Relatedhave been trying to connect my Wi-fi Access point but sytem shows , windows was unable to connect , however i have checked that access point with my friend laptop that was working fine, i have re installed my wi-fi network adapter , but the problem is same.
View 1 Replies View RelatedI recently switched from DSL to cable. No issues on DSL. Since switching to cable, I haven't been able to connect more than one computer to the wireless access point at one time. I have three computers, one running W7, one on xp, and one on Vista. All three of the computers have been able to connect to the WAP when connecting alone.I am using a wap54g linksys access point. Setup is internet --> coax --> cable modem --> ethernet --> wap[CODE]
View 2 Replies View RelatedI want to use my PC for internet access in my office (shed)Shed does not have phone line or cable points.PC does not have wireless capability.Moile phone can be used as Access Point (but PC can't detect it- no wireless capability)What is the methods to provide plug-in/ bolt-on wireless capability for my PC so that it can use my mobile Access Point to connect to the internet?
View 2 Replies View RelatedI have set up an access point as per the instructions I found on this site. It works perfectly, holds a wireless signal fine. Now, I have the challenge of trying to remote connect to the home computer that is connected to this access point. I have absolutely no clue as to what changes in settings have to be made.
View 4 Replies View Related
