I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
I purchased this router a few days after its release, and I was very impressed with its functions. I came from a DD-WRT flashed router with all the bells and whistles, and the E4200 lacked some features but I felt it was a fare trade off for the GHz & dual band.All was well with all my settings (quite a few to name QOS,forwarded, etc)I also updated the firmware when it came available and re entered same settings.
Approx 3 months after use I had 0 WAN connection via eth0 or WIFI, when I logged into router I was pulling a Public IP from my ISP. I could ping from inside the router but no connection on any hosts, very strange. Powercycling Modem/Router yielded same results.. I then backed up my vast amount of settings, and did a 30/30/30 reset.. With no configs I had no issue browsing on any host on my network. So I restored from backup and the issue was back again..So I did another 30/30/30 reset. Then went and reentered the exact same settings as before and the issue was gone.
I am using Linksys E4200 wireless router. I connected two machines, this way.
|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
I'm using Linksys E4200 router. I can't seem to ping the static WAN IP (from internally or externally). All other connectivity seems to be fine. I can ping the routers internal IP, as well as the cable modem and other external IPs. But all port forwarding through the E4200 is failing.Should the default security/firewall setting allow port forwarding? Or do some settings need to change?
View 2 Replies View RelatedI have an E4200 and have added it to my network with a new static IP and DHCP and firewalls off.It runs off my cable modem and router (Virgin Media Superhub) that has DHCP.When I tell it to do a firmware update, traceroute or ping it fails, just wont do any of them.
View 9 Replies View Relatedjust replaced a WRT54G with E4200. Most functions work well. 4 wireless computers (1 Macbook, 3 Win 7), 1 wireless android, 1 wired Win7 computer, 1 ethernet connected hard drive, 1 ethernet connected printer. All computers can ping router, access hard drive, access internet, ping android and ping Macbook.However, router, nor any computer, can't ping Win7 computers. Apparently IP based connections between WinX computers is blocked. My real applications are to Remote Desktop Connect from 1 Win7 computer to another, or to run a DLNA music server on 1 Win7 computer, accessed by another. (the LAN connected computer is the server, accessed by a wLAN client. All worked fine on WRT54G router, but can't connect thru E4200. When these apps failed, I tried PING, and that failed as well.All computer's IP addresses are properly served from E4200 via DHCP, and are visible thru the router's DHCP Reservation panel.
View 1 Replies View RelatedI recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.
View 4 Replies View RelatedI have recently purchased a E4200 i have flashed it with the latest Firmware 1.0.03 and Hard Reset the Router so the Media issue was resolved i was having. After upgrading the firmware to the latest version my Nortel VPN IPSEC Client no longer will work. The tunnel is connected and it passes traffic for about 15 seconds then nothing. The connection remains connected but no traffic passes cant ping across tunnel. I have checked all the settings and VPN - IPSEC - Passthru is enabled. I have put the client in DMZ mode and tried that same thing.
View 7 Replies View Relatedi have my Cisco E4200 set up with a 6rd tunnel. the tunnel seems to work fine for the most part. i can ping ipv6.google.com and get a response.however, i cannot ping the addresses of the IPv6 Tunnel ends from within my network. If i run a ping from outside the network, i can ping the IPv6 address of the server end, however, i cannot ping the E4200's end of the tunnel. is there a specific option that needs to be set? i have allowed ping so that my IPv4 address is pingable, am i missing something for IPv6?
View 7 Replies View RelatedI noticed some serious random ping spikes in online games and found that the connection between my Laptop and the E4200 is very very unstable. Sometimes it works perfectly fine but at other times my ping will spike each 5 seconds to three or even four digits and back to normal. I never get disconnected but playing is obviously not possible.
I ran several pingtests through pingtest.net and got everything from 15ms ping 3ms jitter to like 400 ping 300 jitter.
Eventually, I pinged the router (192.168.1.1) and got delays between 2ms and 300ms for both the 2.4 ghz and the 5ghz network. The 2.4ghz channels are fairly crowded but the signal is perfectly fine and stable. The 5ghz band is totally free therefore interference shouldn't be a problem i guess.
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies View RelatedRouter: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
I just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies View RelatedBeen more than 2 years since I purchsed this router from US and has been working flawlessly till now. Lately I have been facing issues with few websites not opening when my laptop is connected to the router using a lan cable. Sites like speedtest.net (I get the download speed but when it needs to upload it is stuck there forever), [URL] is another which just does not open.
I tried opening these sites using e4200 wifi and everything works perfectly. I even updated the firmware to the latest 1.0.05 build 7 Aug 23, 2012 but still the same issue.
My router set to Automatic configuration - DHCP...
Also when I directly connect the internet cable to my laptop lan, everything opens without any issues.
I recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
Upon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies View RelatedI've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies View RelatedI have a non linksys modem router with wifi capabilities.I want to connect wirelessly the E4200 with my modem/ router ... After that, I want to be connected ONLY to the E4200, wirelessly and wired TOGETHER to have internet to my desktop pc (via lan cable) and to my wireless clients (via wifi).
View 6 Replies View RelatedIt would be nice if there was a "Note" field next to each MAC field whereby you could specify what device the MAC belongs to. I have quite a few listed but recently I've gotten rid of the devices. I have to go through all my current devices, not them in another program, and then remove the ones that are no longer needed.
The Wireless Client List doesn't capture all the names so that's not what I'm looking for.
Also, it would be great if the "Note" would tie into the Parental Controls so that I know exactly what device I'm choosing. It currently lets you select from the Wireless Client List, but the list doesn't have all the Client Names populated.
So, one, is this feature available (or something similar) and two, if not, please take this into consideration as a useful feature for a new version down the road.
My e4200 v2 arrived today to replace my v1. I installed it along with a re1000 range expander for our big home. Works pretty well now, but did some google searching and it seems i could make my original e4200 into a bridge, would this be the way to go for max wifi? I could run a cat 6 cable upstairs along the outside of the home fairly easily.
View 9 Replies View RelatedHave a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
I think i have tried everything i could think of to forward port 5900 with no luck. iIhave e4200. it is for RealVNC application. I followed steps from here: i have windows 7 and nortonn internet security. i disabled the firewall and added a rule to forward port 5900 in windows but did not work either.
View 9 Replies View RelatedI am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.
View 9 Replies View Relatedwell, i just bought an E4200 and, by the way, was very hard to configurate. But the real problem is: if there is a power loss, both modem and e4200 lights up, but no internet connection is provided.Even the SSID desappear. I trried to disconnected everything, reconnect by parts, but no success.I wired connect the E4200 to my iMac and the router was ok, configurated.Then, i reconnect to the modem and all worked ok.Now im testing possibilities and is i reboot the router, the net desappear and i have to try possibilities till it works.
My older router connected automatically, without a problem, but i decide to buy "the best" brand and its top product". Now im disappointed..
Twice i realize that if the connections drops out, i have to disconnect and reconnect the internet cable from my E4200...
I am having a trouble with my router, our modem is the one that is connected to a TV box and it comes with a wifi function(a modem with a wifi function). I am not sure how to set it up, so I connected it to E4200 which is located in another room using CAT6 flat cable and set it to "Bridge mode". But whenever I open the TV box, the wifi won't work, and when it's closed, it works. :s how weird is that. Are there any problems? The modem with wifi will always work either way I open/close the TV box, but the E4200 wifi will only work when I close the TV box. I asked my service provider about this and they tell me it's not their problem anymore.
View 2 Replies View RelatedI just purchased an e4200 in a corporate environment where we already have a wireless router. I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless). I set the Linksys to bridge mode and assigned it an ip address. I disabled all wireless settings, etc. I then connected the internet port of the Linksys into a data port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this.
View 3 Replies View RelatedI recently bought an E4200 and noticed that the wireless speed keeps dropping as it stays connected.As soon as I power it on, my iPhone and notebook connect at 54Mb, but as they remain connected, the speed keeps dropping to 48, 36 and one morning, my phone was oscillating between 5 and 11. The iPhone was almost at the same spot, and the signal was around 85~95%. On my 3 year old DIR-300, the speed don't change at all, and it's in a place where I can see around 15 connections. On the E4200 I can only see 2 other networks.I've already tried switching channels, fixed and auto channel, updating firmware and a few other common configurations. At first, I thought it was my repeater, but I turned it off and it didn't work. Turn my cordless phone off didn't change it also.
View 3 Replies View RelatedI just got an e4200 and I'm haviong very disappointing wireless speeds. My network is setup as follows
powerline----------desktop
|
|
powerline-----------wireless router ----------- laptop (using USB adapter Linksys AES1000, Intel bng internal, Belkin adapter)
If I plug into the back of the e4200 I can download at roughly the raw speed of the powerline 7 MBps. So I know the powerline connection is just fine and the routing function of the e4200 is just fine. When I use my laptop my speeds are wildly variable on both 2.4 and 5 ghz. With a clear line of sight to the router (maybe 7 feet away) they seem to hover around 1.5 MBps but have reached as high as 5.5 MBps twice. Using my much cheap older Buffalo router I routinely get speeds in the 4.5 MBps range which I would consider acceptable (although it has other, separate issues). I have followed all of the advice I can find on the forums. The range is also pretty terrible. If I'm 20 feet away and no longer have a clear line of site to the router I will frequenly have almost no signal and miserably slow download speeds in the kbps.I have made sure that I am using wpa2 with AES, I have changed my MTU to 1365, I have updated the firmware to the one released in March, and I have explored setting different channels on the router to no avail. I also contacted tech support which I'm only marginally sure understood that I was talking about the LAN connection and not the internet.
Why I must restart my e4200 after 2-3 days when I want to connect my device like notebook or phone to the router. After restart my device can obtain the ip. I hardly to turn off the router.Is something wrong with my router ? [code]
View 2 Replies View RelatedThe task is to share Internet via Wireless router for visitors without any Proxy/Windows Domain authentication.We have:1) Windows based Domain with Active Directory Users, with no DHCP setup, only Static IPs allowed. Used as a DNS server, the IP-address is 192.168.1.1, Domain name, say, Internet Connection via Proxy server which authenticates users via above-mentioned DNS server, the Proxy server IP-address is 192.168.1.3, ruled by MS TMG (ISA server)3) A Wi-Fi Router Cisco E4200.The local area network is wired and works fine. Domain users are happy.The idea is to make visitors happy with a free Internet connection without wiring them into the LAN.So:1) Respected visitors would not have to set up static IP-adresses on their devices to connect to Internet and2) Respected visitors would not have to enter domain credentials to get access to Internet, but3) Network security should not be jeopardized.
View 3 Replies View Related