Linksys Wireless Router :: E4200 V2 Unable To Access Most Websites
May 24, 2012
I recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
View 4 Replies
ADVERTISEMENT
May 3, 2012
I've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies
View Related
Jan 16, 2013
Been more than 2 years since I purchsed this router from US and has been working flawlessly till now. Lately I have been facing issues with few websites not opening when my laptop is connected to the router using a lan cable. Sites like speedtest.net (I get the download speed but when it needs to upload it is stuck there forever), [URL] is another which just does not open.
I tried opening these sites using e4200 wifi and everything works perfectly. I even updated the firmware to the latest 1.0.05 build 7 Aug 23, 2012 but still the same issue.
My router set to Automatic configuration - DHCP...
Also when I directly connect the internet cable to my laptop lan, everything opens without any issues.
View 4 Replies
View Related
Dec 4, 2012
I have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....
View 1 Replies
View Related
Feb 17, 2013
I've been having a strange intermitent problem with my E1500 wireless router. When we first bought and installed it everything was working well with no known problems. After several months no one using the router was able to access certain websites as well as a game server that we play on. No one had made any changes to the router settings and I assumed at first that it was an ISP problem. After talking with our ISP tech support they finally suggested plugging my PC directly into the modem rather then the router. I did and found that the websites and servers that previously wouldn't connect while using the router were now reachable. Any changes to the router settings since installation.I decided that just in case someone unauthorized had made changes to simply revert the router to factory settings and reinstall the software. After doing this I found that I could again reach the websites and servers that I previously could not. So time went on with no problems until a few months later when the same websites and servers were again unreachable by anyone on our router. I again reset the router to factory settings and changed passwords as a precaution, but this time the websites and servers were unreachable even though I had just reset the router.
View 7 Replies
View Related
Jun 15, 2012
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
View 2 Replies
View Related
Apr 18, 2012
I just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies
View Related
Sep 18, 2011
Upon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies
View Related
Sep 11, 2012
Is there a way I can monitor what web sites are visited through my E4200 V1 (firmware v1.0.04)
View 3 Replies
View Related
Jul 25, 2012
I just got an e4200 refurbed router, and it's been working great except for one problem I'm having. I have Comcast cable with Ubee D3.0 modem. For some reason, there will be a random 4-8 second delay when going to certain websites. While this normally wouldn't be a problem, it occurs quite frequently with Google.com and we definitely can't have that. I've updated to latest firmware. Ran ping test to find optimal MTU, went with 1500. To be sure it isn't a DNS issue, tried accessing Google by IP addy and getting the same delay. The delay seems to occasionally occur with Facebook as well, at one point I couldn't even get to Facebook and had to release/renew ipconfig. I have Mac address cloned if that makes a difference.
View 4 Replies
View Related
Apr 19, 2013
I have a E4200 V1 router. A website that I have been accessing for years all the sudden no longer works. If I use my PC and PPTP VPN to another location, I can browse the website fine. If I remove the router and plug directly into my Comcast internet connection, I can browse the website fine. If I enable logging on the router, it shows the connection on port 80 just like every other outgoing connection. Security log shows nothing. I was on firmware version 1.0.03, upgraded to 1.0.05. Tried resetting to factory defaults before I updated firmware, and after I updated the firmware. The website all the sudden just stopped working 2 weeks ago. I also tried putting my PC as the DMZ IP address and nothing.
View 1 Replies
View Related
Dec 20, 2012
I installed a X3000 yesterday. I notice I can't access parts of certain websites - it seems to be just those parts of each site where a logon/password is required.My wireless dongle on the same laptop works OK, so it seems to be a router problem?
View 3 Replies
View Related
Dec 24, 2012
Got a new EA4500 for Xmas. After setting up the new router I could only access you tube and Google at a very slow speed, however I can not access any other website - Facebook, yahoo and etc... it would ping yahoo and Google no problem friend told me to do a tracer to some ip address and his conclusion was the router is fully functional
ISP uses PPPoE, Im sure that the username and password are correct. upgraded to the latest firmware manually, and holy hell accessing the router with no internet access.
View 5 Replies
View Related
Sep 12, 2012
Possible to set up access restrictions to Allow only specific websites?
View 1 Replies
View Related
Aug 23, 2011
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies
View Related
Oct 23, 2011
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
View 9 Replies
View Related
Mar 12, 2012
Have a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
View 5 Replies
View Related
Nov 20, 2011
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
Sep 27, 2012
I think i have tried everything i could think of to forward port 5900 with no luck. iIhave e4200. it is for RealVNC application. I followed steps from here: i have windows 7 and nortonn internet security. i disabled the firewall and added a rule to forward port 5900 in windows but did not work either.
View 9 Replies
View Related
Feb 11, 2012
I am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.
View 9 Replies
View Related
Jan 27, 2012
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
May 22, 2012
I have an XP machine that i am not access websites from. the machine is hardwired into a router, the other computers connected to the router(wifi) are able to get access websites without issue.here are the steps i have taken and the things i know so far.im pulling a valid ip address, with correct dns/gateway all that good stuff
able to ping other machines on the network, pings the router, and able to ping google.com(so i know there is connection between me and the internet, and that dns is working)
installed firefox to see if it was a problem with IE, no go.took a look at the active process and looked up anything that wasnt familiar, that seems to be good.virus scan with avast came up clean, avast is able to connect to its database and pull the most current virus defs.
there isnt a firewall, the only security measures on the computer is avast.
View 1 Replies
View Related
May 7, 2012
I am using Linksys E4200 wireless router. I connected two machines, this way.
|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
View 2 Replies
View Related
Jul 17, 2012
I've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
View 4 Replies
View Related
Feb 5, 2012
I've installed aDIR655 for my friend's cafe and found that Clients ( both wired and WIFI ) have difficulties accessing Yahoo and MSN while Googles etc ( and other Newspaper and webmail sites are OK ) is fine.....I tried to reload and reboot and re-config etc but all in vain...
View 1 Replies
View Related
Feb 23, 2012
I have a E4200 router. The firmware version is 1.1.02. I am reluctant to upgrade; however, my iMAC is picking up the 5GHz broadcast setting, but the rest of my wireless devices only recognize my lower 2.4GHz setting. I have changed channels, my router address is changed because it conflicted with my Verizon DSL. I do not have FIOS. What can I do to fix this problem. I have an ipad, 2 iphones, 2 ipod touches, 2 laptops (PCs), an XBOX, and a PS3 that needs to connect to a higher broadcast. The connections are slow and at times get dropped.
View 4 Replies
View Related
Nov 15, 2012
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
View 9 Replies
View Related
Nov 10, 2012
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
View 4 Replies
View Related
Jun 18, 2012
I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
View 9 Replies
View Related
Jan 31, 2012
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
View 9 Replies
View Related
May 24, 2012
I recently put in a surveillance system with remote access. I have an application on my android phone and it can be viewed by any browser. While I am connected to my network these functions work fine, on my phone and any desktop/laptop. The problem happens when I try to view remotely, off my network. I had this setup on my Netgear router before I got my new fancy schmancy Cicso router becaue the netgear wasn't cutting the cheese in keeping my wireless connectionstory.So here is what I got. I need 3 ports forwarded for this work, and how I got it work on my Netgear. I have these 3 ports forwarded as single ports. I have them forwarded in a range and I have port triggering turned on. No matter what or which combination of these few things I try, I can't access the DVR remotely, again unless I'm local to MY network.Some additional notes - the DVR has a static address and that address has been reserved in the DHCP settings of the router.
View 5 Replies
View Related
Nov 13, 2011
I have a problem te access e4200 with web access on a iMac with Lion 10.7. I try to connect with standard Safari.With 192.168.1.1. it won't open, if I look voor IP address it should be 192.168.0.1. now the login screen opens but now I can't login with clean name en password "admin" it gives an error.I also can't install Ciso Connect from CD, it gives a error not right version!.Is there anyone that use iMac with E4200 and Sonos zone player?
View 3 Replies
View Related
Aug 11, 2011
how to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies
View Related
