Linksys Wireless Router :: Unable To Open Few Websites Using E4200 On LAN
Jan 16, 2013
Been more than 2 years since I purchsed this router from US and has been working flawlessly till now. Lately I have been facing issues with few websites not opening when my laptop is connected to the router using a lan cable. Sites like speedtest.net (I get the download speed but when it needs to upload it is stuck there forever), [URL] is another which just does not open.
I tried opening these sites using e4200 wifi and everything works perfectly. I even updated the firmware to the latest 1.0.05 build 7 Aug 23, 2012 but still the same issue.
My router set to Automatic configuration - DHCP...
Also when I directly connect the internet cable to my laptop lan, everything opens without any issues.
View 4 Replies
ADVERTISEMENT
May 24, 2012
I recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
View 4 Replies
View Related
May 3, 2012
I've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies
View Related
Mar 12, 2012
Have a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
View 5 Replies
View Related
Nov 26, 2011
There's a WRT54G2 v1.5 router in the apartment I just moved in to (belongs to my roommate) which crapped out the other day. My computer and iPod touch both recognize the router's signal and connect to it, but I can't access any Web sites after that (both work fine on other wireless networks). I can, however, access the Web via the cable modem, but when I plug an Ethernet cable into one of the ports on the Linksys router, I have the same problem as when I'm connecting wirelessly. So far, I've tried resetting the router (with the reset button on the back), updating the firmware, changing settings (beacon interval, frag & RTS thresholds....saw that suggested on other forums) & leaving the network unsecured (it's currently WPA2/TKIP & AES, what it was originally).Is it safe to say this router's done for, or is there anything else I can do to resurrect it?
View 1 Replies
View Related
Sep 11, 2012
Is there a way I can monitor what web sites are visited through my E4200 V1 (firmware v1.0.04)
View 3 Replies
View Related
Jul 25, 2012
I just got an e4200 refurbed router, and it's been working great except for one problem I'm having. I have Comcast cable with Ubee D3.0 modem. For some reason, there will be a random 4-8 second delay when going to certain websites. While this normally wouldn't be a problem, it occurs quite frequently with Google.com and we definitely can't have that. I've updated to latest firmware. Ran ping test to find optimal MTU, went with 1500. To be sure it isn't a DNS issue, tried accessing Google by IP addy and getting the same delay. The delay seems to occasionally occur with Facebook as well, at one point I couldn't even get to Facebook and had to release/renew ipconfig. I have Mac address cloned if that makes a difference.
View 4 Replies
View Related
Sep 8, 2012
A external scan has reviled that I have an open port. For security reasons I want to close it. I do know the port number.
View 7 Replies
View Related
Mar 5, 2012
How do I go about opening specific ports on an E4200?I'm having disconnect issues with a particular game, and the Customer Service drone thinks the ports required for the game aren't open. Nevermind the fact that it's worked fine for 6 months now, and the problem only started a few days ago.I figured I'd humor the idiot and open the ports, but all I can find is information on forwarding, not making sure the ports are open
View 3 Replies
View Related
Dec 4, 2012
I have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....
View 1 Replies
View Related
Aug 13, 2012
I'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.
View 1 Replies
View Related
Jun 11, 2011
When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies
View Related
Jan 6, 2012
how to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies
View Related
Oct 24, 2011
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
View 7 Replies
View Related
Aug 17, 2011
I own an E4200 and my wife and I use Goodreader on our ipads at home. To add docs to goodreader we need to connect to the ipads ip on port 8080 but the E4200 is blocking all traffic for it. How can I open port 8080 for our 2 ipads?
View 1 Replies
View Related
Feb 17, 2013
I've been having a strange intermitent problem with my E1500 wireless router. When we first bought and installed it everything was working well with no known problems. After several months no one using the router was able to access certain websites as well as a game server that we play on. No one had made any changes to the router settings and I assumed at first that it was an ISP problem. After talking with our ISP tech support they finally suggested plugging my PC directly into the modem rather then the router. I did and found that the websites and servers that previously wouldn't connect while using the router were now reachable. Any changes to the router settings since installation.I decided that just in case someone unauthorized had made changes to simply revert the router to factory settings and reinstall the software. After doing this I found that I could again reach the websites and servers that I previously could not. So time went on with no problems until a few months later when the same websites and servers were again unreachable by anyone on our router. I again reset the router to factory settings and changed passwords as a precaution, but this time the websites and servers were unreachable even though I had just reset the router.
View 7 Replies
View Related
Apr 19, 2013
I have a E4200 V1 router. A website that I have been accessing for years all the sudden no longer works. If I use my PC and PPTP VPN to another location, I can browse the website fine. If I remove the router and plug directly into my Comcast internet connection, I can browse the website fine. If I enable logging on the router, it shows the connection on port 80 just like every other outgoing connection. Security log shows nothing. I was on firmware version 1.0.03, upgraded to 1.0.05. Tried resetting to factory defaults before I updated firmware, and after I updated the firmware. The website all the sudden just stopped working 2 weeks ago. I also tried putting my PC as the DMZ IP address and nothing.
View 1 Replies
View Related
Mar 24, 2013
I am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G. I am unable to open any ports. I upgraded to the latest firmware yesterday but still am unable to open any ports. I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports.
View 2 Replies
View Related
Jun 2, 2012
I have a wrt120n wireless router and use Network Magic Essentials with 2 computers on my network. It has worked fine for about 2 years. I recently upgraded the desk top from an XP pro service pack 2 to a service pack 3. I am now unable to receive files from my laptop which is a Vista or print from the laptop. I can receive files on the laptop from the desktop. I am running McAfee and have spent about 3.5 hrs with a tech there but they have not been able to find any problems with their system.
View 3 Replies
View Related
Jun 15, 2012
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
View 2 Replies
View Related
Aug 23, 2011
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies
View Related
Oct 23, 2011
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
View 9 Replies
View Related
Apr 18, 2012
I just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies
View Related
Sep 18, 2011
Upon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies
View Related
Nov 20, 2011
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
Sep 27, 2012
I think i have tried everything i could think of to forward port 5900 with no luck. iIhave e4200. it is for RealVNC application. I followed steps from here: i have windows 7 and nortonn internet security. i disabled the firewall and added a rule to forward port 5900 in windows but did not work either.
View 9 Replies
View Related
Feb 11, 2012
I am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.
View 9 Replies
View Related
Jan 27, 2012
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
May 7, 2012
I am using Linksys E4200 wireless router. I connected two machines, this way.
|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
View 2 Replies
View Related
Jul 17, 2012
I've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
View 4 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Feb 23, 2012
I have a E4200 router. The firmware version is 1.1.02. I am reluctant to upgrade; however, my iMAC is picking up the 5GHz broadcast setting, but the rest of my wireless devices only recognize my lower 2.4GHz setting. I have changed channels, my router address is changed because it conflicted with my Verizon DSL. I do not have FIOS. What can I do to fix this problem. I have an ipad, 2 iphones, 2 ipod touches, 2 laptops (PCs), an XBOX, and a PS3 that needs to connect to a higher broadcast. The connections are slow and at times get dropped.
View 4 Replies
View Related
May 23, 2012
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies
View Related
