I installed a X3000 yesterday. I notice I can't access parts of certain websites - it seems to be just those parts of each site where a logon/password is required.My wireless dongle on the same laptop works OK, so it seems to be a router problem?
View 3 RepliesThe HD connected to my X3000 Router is recognized and visible (shared folder) from my media player connected to my TV. However I can't see it from my computer to add/remove files. Isn't it possible to administer the files on the drive without disconnecting it from the router and connecting it to the computer?
View 2 Replies View RelatedGot a new EA4500 for Xmas. After setting up the new router I could only access you tube and Google at a very slow speed, however I can not access any other website - Facebook, yahoo and etc... it would ping yahoo and Google no problem friend told me to do a tracer to some ip address and his conclusion was the router is fully functional
ISP uses PPPoE, Im sure that the username and password are correct. upgraded to the latest firmware manually, and holy hell accessing the router with no internet access.
I have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....
View 1 Replies View RelatedI recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
I've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedI've been having a strange intermitent problem with my E1500 wireless router. When we first bought and installed it everything was working well with no known problems. After several months no one using the router was able to access certain websites as well as a game server that we play on. No one had made any changes to the router settings and I assumed at first that it was an ISP problem. After talking with our ISP tech support they finally suggested plugging my PC directly into the modem rather then the router. I did and found that the websites and servers that previously wouldn't connect while using the router were now reachable. Any changes to the router settings since installation.I decided that just in case someone unauthorized had made changes to simply revert the router to factory settings and reinstall the software. After doing this I found that I could again reach the websites and servers that I previously could not. So time went on with no problems until a few months later when the same websites and servers were again unreachable by anyone on our router. I again reset the router to factory settings and changed passwords as a precaution, but this time the websites and servers were unreachable even though I had just reset the router.
View 7 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedOver the passed couple of weeks I have experienced issues trying to connect to the internet via the LAN Ports. My main PC and a Xbox cannot connect to the internet even though 3 laptops have no problems using the Wifi connectivity.I have had two live chats with Cisco engineers and the first resolution was to perform a firmware upgrade which did solve the issue for a day or two. I think it was more to do with reset the modem/router rather than the firmware upgrade. The second session ended with the eingineer advising me to take the equipment back to PC and seek a replacement simply because Ciso have nothing in writing relating to this problem.
View 6 Replies View RelatedI am using the x3000 as a modem and router, and I managed to set up the device yesterday through the web interface (192.168.1.1).However, after less than 24 hours of continuous usage, I cannot access the interface for some odd reason. I tried using the disk that came with the device but the software reports as if I am not connected to the router. I tried pinging 192.168.1.1 and I get >1 ms so that confirms the device is active and responsive.
View 1 Replies View RelatedI am experiencing one, possibly two problems with the X3000, firmware release v1.0.03:
1. When enabling guest mode, the internal network is not accessible via WLAN even for clients NOT connected via guest mode but regularly: Even non-guests but regularly connected clients can't access any internal IP but the router itself. netscan shows only the very client's IP and the router's. Only after switching guest mode entirely off, regularly connected clients can access interal IP again. netscan correctly shows the whole network. Obviously a firmware bug. BTW: Clients connected via cable do not experience this problems.
2. I am not sure about this, but after using the firmware built in "Reboot" button, the router reboots correctly. But for some reason, it is instable afterwards. It is operational for a few seconds but then reboots again. It keeps cycling. I could stop it by switching the router off and on again.
I've just upgraded my home wireless from an NetComm NB5540 + modem to a LinkSys X3000.Internet access works fine for all devices, but some wireless devices can't "see" my Win7 desktop system that's on a wired connections to the router. Galaxy Note phone (running ICS 4.0.4) can discover and connect to file shares on my desktop system without any problems.Asus Transformer Prime tablet (running JellyBean 4.1.1) can see the router on the local network, but can't see my desktop. Even if I manually type in the IP address it can't connect to itLikewise my old WinXP laptop can see the router but can't see or connect to any other devices.
I tried connecting the NetComm router with just Wifi configured to one of the ethernet ports on the X3000, so I've got two Wifi networks running in parallel. If I connect to this second WiFi network with any of the above devices then they can all discover and connect to my desktop system on the wired connection to the X3000.
not being able to block websites like facebook and youtube on the router.
View 4 Replies View RelatedIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
I use a WRT54G wireless router connected to Mac. All of a sudden, I became unable to access certain websites on my iMac, such as Facebook and Apple homepages. But i can access Yahoo website. I tried resetting my linksys setup but it doesnt solve the problem. When i access my iphone via wifi at home, i am also unable to go into app store, facebook app, and emails with images won't load. I also cannot link my iphone to itunes on my iMac. What happens on my computer when I surf the internet is that the page just loads halfway and stop "responding". But my imac airport says that my internet connection is fine, however my access has become very "restricted".
View 1 Replies View RelatedHow can I block certain websites in my E1200 router? I badly need it...
View 3 Replies View RelatedIs there a way I can monitor what web sites are visited through my E4200 V1 (firmware v1.0.04)
View 3 Replies View RelatedBeen more than 2 years since I purchsed this router from US and has been working flawlessly till now. Lately I have been facing issues with few websites not opening when my laptop is connected to the router using a lan cable. Sites like speedtest.net (I get the download speed but when it needs to upload it is stuck there forever), [URL] is another which just does not open.
I tried opening these sites using e4200 wifi and everything works perfectly. I even updated the firmware to the latest 1.0.05 build 7 Aug 23, 2012 but still the same issue.
My router set to Automatic configuration - DHCP...
Also when I directly connect the internet cable to my laptop lan, everything opens without any issues.
how to setup WRT54G for blocking all unwanted websites for users. When tried to configure Website under Access Restrictions tba, it accepts. However it doesn't block.
View 1 Replies View RelatedShort version: when running devices through my e2000 into my CM100 modem, internet access is unstable, packets are lost, and certain websites simply will not load. I am using my apartment complex's **bleep** internet (and I have no choice in the matter) which registered the MAC address of the CM 100. When I run through the CM100 directly, everything works fine. What can I do to fix this?
Long version: I have an e2000 router connected to my PC, Xbox, and wireless devices. The router is then connected to a CM100 cable modem. The modem is connected to my apartment complex's internet access. They required the MAC address of the cable modem. The routed showed an apartment complex domain when I went hunting around, but there is no login to it, and I was never told anything else about the connection.
When I run the router through the modem, the internet access is lousy. Certain websites will never load, the connection drops, and packets are lost. When I run directly through the modem, the connection works perfectly.
I note that the CM100 assigns IP addresses if it cannot get any from the ISP, and there appears to be no way to turn it off. I have tried disabling DHCP on the router, but it did not work. I have changed the router's IP address, but that did not work. I have even tried turnign the router into a simple wireless access point, but that did not work. The modem is at 192.168.100.1, while the router is on 192.168.1.1. Should I change my router's location to 192.168.100.x?
I'd like to block all websites except a handful. how can i do this?
linksys wrt54g
There's a WRT54G2 v1.5 router in the apartment I just moved in to (belongs to my roommate) which crapped out the other day. My computer and iPod touch both recognize the router's signal and connect to it, but I can't access any Web sites after that (both work fine on other wireless networks). I can, however, access the Web via the cable modem, but when I plug an Ethernet cable into one of the ports on the Linksys router, I have the same problem as when I'm connecting wirelessly. So far, I've tried resetting the router (with the reset button on the back), updating the firmware, changing settings (beacon interval, frag & RTS thresholds....saw that suggested on other forums) & leaving the network unsecured (it's currently WPA2/TKIP & AES, what it was originally).Is it safe to say this router's done for, or is there anything else I can do to resurrect it?
View 1 Replies View RelatedI am getting 404 messages but the browser is connecting to the site's server (you can see the little icon for each site in the tabs). The two sites I have identified that I cannot access are UIowa libraries and Music from Outer Space.
-I have emptied all cache, cookies, etc.
-I have reset the router to factory defaults and updated the firmware
-I can load both sites from other networks, however two different computers using my router fail to load these two sites.Until a couple days ago I was able to access both of these sites regularly, and I haven't installed anything or changed any settings on my computer.The fact that two different computers cannot load these sites seems to indicate that it is a router problem.
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies View RelatedI recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies View RelatedIs it possible to have multi PVC for IP TV in x3000 adsl router ?
View 1 Replies View RelatedI recently purchased an E-2500, but notice that in parental controls I can only block 6 or 8 websites. In my WRT54GS I could just create additional rules and they would work. But in this device I am limited on the sites that can be blocked per device. How I can block additional sites?
View 1 Replies View RelatedI have on Desktop wired to the router which is my main pc. When I access internet the website load really slow, but when I connect the pc directly to Comcast modem, it's blitz fast. My internet speed is 15 Mbps. I have another desktop and laptop. None of them have the problem. What settings I have to change to get back to speed I used to have before.I messed up some settings on the Cisco Connect and accidentally reset the router. After re-installing the router the problem started.
View 9 Replies View RelatedI am attempting to install the router but cannot connect to SKY ISP. I can connect my laptop to the router both wirelessly and by cable.
View 5 Replies View RelatedI just got an e4200 refurbed router, and it's been working great except for one problem I'm having. I have Comcast cable with Ubee D3.0 modem. For some reason, there will be a random 4-8 second delay when going to certain websites. While this normally wouldn't be a problem, it occurs quite frequently with Google.com and we definitely can't have that. I've updated to latest firmware. Ran ping test to find optimal MTU, went with 1500. To be sure it isn't a DNS issue, tried accessing Google by IP addy and getting the same delay. The delay seems to occasionally occur with Facebook as well, at one point I couldn't even get to Facebook and had to release/renew ipconfig. I have Mac address cloned if that makes a difference.
View 4 Replies View Relatedwrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies View RelatedAfter upgrade to FW .04 on x3000 the router dramatically decreased the internet speed, besides the already discussed problem with cookies and authentication. Any archive for 1.00.03 (previous FW) - I think downgrading now is the only way to hve the router back to normal.
View 9 Replies View Related