My Belkin N150 wireless router monitor has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you us a solution is available.I can not figure out why my wireless router doesn't work sometimes.I need to be able to access this to get to the router settings. I don't know if my wireless is being highjacked or what.
View 2 RepliesBelkin Setup / Router monitor application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.
View 1 Replies View RelatedHaving the same problem with a Dell Inspiron Laptop using a belkin pcmcia wireless card. It was working, but has stopped doing so. I was missing some network adapters which I have reinstalled, and the hard wired connection is now working again, but wireless will not get past the acquiring network address phase. I tried the ipconfig /all and it shows my IP address as 0.0.0.0 and the same on the subnet mask. it says the autoconfig is enabled and dhcp is enabled. My HP laptop is connecting to the wireless network just fine.
View 1 Replies View RelatedMy wireless router stopped working. diagnostics messages say it could be either bad ethernet cable (not the problem as I am using the cable right now to plug directly in to cable company modem to gain access to internet) OR "drivers not being recognized"
View 1 Replies View Related[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies View RelatedI have a Century Link modem connected to a Linksys router. I have three computers hooked up wireless. I used another computer to hook up with the ethernet cable because that wouldn't work wireless for some reason. A little while after that, the Linksys network stopped working completely(all three computers could not access the internet). Now I can only connect to the internet if I use a ethernet cable from the modem.
View 2 Replies View RelatedMy dlink dir 628 wireless router suddenly stopped working yesterday. If I plug the ethernet cable directly into my computer and the internet works. I see the wireless profile in the options for the wireless internet, but when I try to connect, it is unable to do so.
I've tried resetting the router (using the button on the device) witand reinstalling the router (using the CD), but still not working. Also have tried turning off the modem, router, and restarting my computer.
My router randomly stopped working after I bumped into the wire. It still shows up as a network you can connect to, but whenever I try to connect, it keeps saying there is a problem with my connection. I tried using a different internet cord, but nothing changes. I even tried to reinstall my router and still no dice.
View 6 Replies View RelatedEA4500 was working fine for about 2 months.Now, its not so happy.Power indicator is on.Plug something into one of network ports - nothing, and no indicator LEDs are on.Plug an operational internet cable into it - nothing, and no indicator LEDs are on.
View 3 Replies View RelatedLast night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?
View 1 Replies View RelatedI have WRT54G connected to a cable modem for internet service. Came home at lunch yesterday and all was working fine. Came home after work last night and couldn't connect to the internet. Called Charter cable this morning and their troubleshooting showed I can connect to the internet fine if I bypass the router, so the issue must be with the router (and of course not their problem...). How do I trouble shoot this? I've tried powering down the router and releasing and renewing IP addresses but it hasn't worked.
View 9 Replies View RelatedI have a Linksys WRT54GS wireless router that has stopped working. All it will do is all 4 of the Ethernet port lights on the front light up solid green along with the Internet light. Is there any hope of fixing this?
It wouldn't make that much of a difference, but I already purchased a new LInksys Cisco EA3500, but I cannot get it to do my port forwarding. I have tried everything and nothing works. Have spent hours on the phone with tech support with no solution. My old WRT54GS just simply worked. The port forwarding worked perfect. I have tried the exact same setup in the new EA3500 and no luck no matter what I try.
So, is there anything I can do to get the old WRT54GS working? I have tried holding the reset button in for 1 minute and then unplugging it
My M20 Valet Plus stopped working suddenly last night. Now no power lights will come on and it now longer transmitts as a connection point . No apparent sign that it's alive. I've owned it troublefree for just over a year, but it is out of warranty. Any way to tell if there is hope of reviving it or if I'm just out of luck? Nothing happened at my end to cause this -- no power interruptions or other odd occurrences.
View 9 Replies View RelatedA couple days ago I noticed that my wireless internet connection on my iPhone would cut in and out, then stopped all together. I also had no connection on my mac which is wired to the WRT110. I bypassed the WRT110 and then I had a connection on my Mac meaning the WRT110 is the problem. I haven't changed or added anything lately that could've caused this....
View 9 Replies View RelatedI have the Linksys WRT54G And it was working fine for years! Then today my computer shut down and when I turned it back on there was a connection but my computer was not responding to any commands. The icon shows full connectivity excellent connection. When I try to go to a web page it shows Connection Error and cannot get to any web pages.I am able to get on other wireless connections from neighbors but not mine. I have gone thru different directions on here and I am not technical and don't understand what is being said. I try to go to 192.168.1.1 and it asks for a password which I don't have. I have tried everything such as password and admin and get nothing.I am able to get my ip address and default gateway address and don't know the next step.
View 1 Replies View RelatedI have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success. I followed the troubleshooting procedure that I found and changed the MTU setting. I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.
View 9 Replies View RelatedI was using my iphone one night last week and suddenly it dropped out and now I cannot find it in my WIFI networks page.I am using a Linksys E1000?
View 9 Replies View RelatedI've had the WRT400N for about a year and a half now and just last night it stopped sending out data when connected to my cable modem. I've tried connecting the modem directly to my Mac and it works just fine (that's how I'm sending this message now). But when the modem is connected to the router, I get no data. It connects to both the 5 Ghz and 2.4 Ghz networks, but it refuses to send data through the pipe. I've tried power cycling both the modem and the router to no avail.
View 1 Replies View Relatedi am a using a WRT54GH linksys router.. which was working fine for a year.. there was thunderstorm and lightning a few days back.. since then my routers internet port (the first port which says internet in yellow) has stopped working..
View 5 Replies View RelatedThe router stopped working for wired connections. I can still go online using my laptop via wifi, but when I connect a network cable to the laptop and turn off wi fi, connection does not work. Can't go online with a desktop with a wired connection to router.Everything else works via wi fi: iPad, android phone, tv with wifi.
View 1 Replies View RelatedI purchased an e4200 about 6 months ago and it worked great until the other night the Internet stopped working on my laptop (wireless). I tried unplugging both my modem (Motorola Surfboard) and router and plugging them back in, but no luck. I can accesss the Internet when plugged directly into the router (with both my PC and laptop), so it looks like the issue is with the e4200. To make matters worse (and I fear much worse), I can't even access the admin page to the router through either the Cisco Connect software or through the IP address. I've tried resetting it, I've tried the 30/30/30 reset (holding the reset button while doing an unplug and pluging back in), and reinstalling the Cisco Connect software, all to no avail.
I've found threads where others have not been able to access the admin page, but they still had access to the Internet url... I haven't found a similar thread where the router doesn't seem to work at all. A few other bits of information I can think of (let me know if there's other information I can provide):The Cisco logo light flashes slowly after reset which I believe is expected.The lights in back of the router seem to work as intended.Running Windows 7 Diagnostics finds the connection "doesn't have a valid IP configuration" and "The default gateway is not available."
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
View 5 Replies View RelatedRegion : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I tried searching google and Cisco Home Community for this answer, but no luck. Maybe I didn't phrase my search correctly. I have an external drive connected to a mac mini which is shared on the network. When transferring folders to or from that external drive, our internet connection stops working until the transfer finishes, then comes back up. I've tested this in a variety of ways. Any transfer of data from shared folders in any combination of devices causes internet to stop working both on wired and wireless devices until the transfer is done, then they all work again. Router firmware: 1.0.03.
View 9 Replies View RelatedAll the lights are on except the wireless one. Wireless network not locatable by laptop even when sitting next to router.
View 19 Replies View RelatedLast night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?
View 3 Replies View RelatedI have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.
View 3 Replies View RelatedRandomly my router stopped working in the middle of the night. I didn't think the issue was with the router so i called the Tech Support people from Brighthouse and they told me to connect directly to the modem so i did that and I had internet. But why would my router randomly stop working, I've had this Linksys Dual N bound router for a year and never had a problem with it. I want to think that its the internet providers fault but I guess I really don't know.
View 2 Replies View RelatedMy Linksys router stopped working. Resetting it didn't restore it.I bought a new Linksys E4200 router and configured it to the same settings as my old router. However, now I can't access certain website like Hotmail, Facebook, a weather site and others.But I can connect to most other websites, stream video, etc. Any suggestions why I can't connect to Hotmail, Facebook, etc???? I have 4 computers (3 wired, 1 wireless) connected through the router and they all do the same thing.
View 5 Replies View RelatedMy router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.
View 3 Replies View RelatedI have a Dlink DIR-615 wireless router that up until a few days ago was working perfectly. Then I had to turn it off at the wall before a storm and it has stopped working. I have tried resetting it with no luck. I am able to get internet try to get onto on my desktop without the router.I have tried to connect to 192.168.0.1 it won't let me. I can't get on there with an internet connection either. As soon as I connect the router the default gateway disappears. [code]
View 5 Replies View RelatedI have belkin f5d7632-4 router, it works ok wirelessley with my smartphone when it is 'open' but setting a passphrase on the router stops access from the phone even with the correct passphrase, other devices act the same as though it is the wrong passphrase
View 1 Replies View RelatedI bought the DIR-655 less than a year ago in Amazon, shipping it to NY. And then I came back to Uruguay. Almost 3 months ago the router stopped working completely and I started to search for support in Uruguay.After calling US support I was told I should contact the local or regional D-Link (which I later found is D-Link LA). And via DLinkLA.com I found the company TELEDATA S.A. url... who does the official support for D-Link in Uruguay. They told me the router couldn't be fixed, and told me DLinkLA, which is based in Chile, would either send me a working one (they also told me the service/warrany was already approved), or send me the money and gave me their contact details.After two weeks of contacting them, trying to get their attention, they finally told me it was not their responsibility because it was bought in the US. And now they don't return my e-mails.
View 5 Replies View Related