Cisco Wireless :: Mixing And Connecting 1262 With 2600 And 3600
Apr 23, 2013I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 RepliesI am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 RepliesAironet 2600 and 3600 series. I need to know their maximum distance (at least theoretically, in Line of sight, eliminating all other factors...) in order to choose the right number of AP to provide enough coverage for a specific area. If an exact number is not available then can you show me how to determine it?
View 8 Replies View RelatedConfiguring HP switches for Flexconnect. I am not sure if or not its doable? Access Points are 2600 and 3600 with 5508 as a controller. Idea is to keep the branch traffic local but the switches are HP.
View 3 Replies View RelatedI know that the deployment guide for 2600/3600 access points states that if you have surveyed for a 3600 deployment, you don't need to survey again for a 2600 deployment. As the the 3600 is the higher specification model, is it safe to assume the reverse? I.e. a site survey carried out using 2600 access points is valid for a 3600 deployment, or is this too simplistic?
View 5 Replies View RelatedI have a strange issue with clients connected to a WiFi network.I have configured AP in FlexConnect mode and 2 SSID's. After a reboot of the AP the network is stable for almost 45 mins. Then each client will go UP and Down, mostly with a delay of 5 mins.
What could be the source of this. The clients are Windows CE handheld with fixed IP adres. I already configure persitent client and have play arround with APR timers as well. Thereby an Windows desktop or an iPad has less connectivity issues but even they expert pakcteloss once in severall minutes.
Session timer is turned off
The iPad for example can play music, but each 5 mins you hear a little hickup and 2 subsecond ping are loss.
Controller version is 7.3
We have a few 1500 outdoor mesh ap's. 1262N are used to link to these 1500 and extend the coverage to places. All 1262 was configured as mesh. But upon installation, none of them actually register to the controller and join the other mesh ap's. They should be joining to the 1500's.
On testing, the 1500 joins the 1262N as mesh. however the 1262N does not join the 1500 as mesh even though the distance is less than 20m.
What would be the ramnifactions of using AIR-1242AG-A-K9 (g radios only: no b clients) and AIR-LAP1231G-AK9 (g radios: only no b clients) with AIR- ANT1728 (non diversity antennas) on the WLAN. Some of the APs 1242/ 1231 will be with in line of site of each other.
View 1 Replies View RelatedI've got a 2600 that I am wanting to connect to my cable modem. However I don't have the knowledge to get it running. My ISP uses a dynamic IP and I am unable to get it to connect.
ROUTER#show run
Building configuration...
Current configuration : 685 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies View RelatedI bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
View 1 Replies View RelatedI'm adding some additional AP's (3502s) to an environment that is all 1131AG AP's. The DHCP is configured for DHCP option 43 for remote sites for layer 3 discovery. Since only one AP mode can use option 43, I've added a DNS entry for cisco-lwapp-controller in my local domain.My assumption here is that the new 3502's will be able to use DNS for discovery, while any additional 1131AG would continue to use DHCP option 43. will this work in a mixed environment?The new AP briefly showed up on my controller, but then disappeared. The LED is cycling red, green, off - indicating it is still in the discovery process. Could I effectively remove the option 43 in DHCP and have all AP's use DNS? Is this as reliable as option 43? What is the best practice for discovery?
View 6 Replies View Relatedquestion on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
We have many remote offices that we want to add public wifi and a couple of other services that would be completely outside of our internal network. Each office has a 3750 with plenty of open ports. How can I safely create a vlan for public access on these switches which currently have our internal network on. I have read that people are doing this to save on the cost of purchasing a dedicated switch. Some people are using access lists and one person mentioned creating a private vlan for the public network. I looked up private vlan and it seemed bit confusing.
View 3 Replies View RelatedIs it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies View RelatedI have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies View RelatedI have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View RelatedI have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
is the aironet 1262 access point a good choice for an environment of about 20 users. each users is in an office and we are looking at deploying the ap at the end of the hall on a wall mount. would distance be a barrier and are there any better options out there?
View 3 Replies View RelatedClient has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies View RelatedI will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View RelatedI currently have WLC 5508 and a few campuses with LAP 1142, each with 2-3 vlan. Now one of our campuses have a building thas is a bit far away and needs network (wired). We can't get fiber or TP-cable there in a good way. So the plan is to get two 1262 or 3500 with AIR-ANT5160NP-R antennas and get a wireless link working between the campus and the building. And then connect one of the AP's to a switch in the other building to provide it with wired network.
The problem is that I can't find information on how to do it. Should both APs be in autonomus mode? I probably only need to have 1 VLAN in the other building but I am not sure yet. Is there a problem with transfering several VLAN over the WLAN-link?
We have 6 1262 APs and a 2504 WLC. 5 of the 1262 appear correctly with 2 radios. One of them shows 1 radio. See screen shots below showing model numbers and interfaces on the AP with one radio available (All other 1262s show 2 radios as normal). Tried resetting the AP to factory default, but same result. Do I have a defective AP?
View 3 Replies View Related1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
I want to replace existing 1242s with 1262s. Which are currently in a Heated Nema Enclosures with 12dBi Mast Mount AIR-ANT24120. The 5.0 Ghz Radio is off. So the question is can I use the same Antennas AIR-ANT24120 for the new 1262? I’m assuming yes as long I use connectors A & C are tx/rx; on the center would we leave open or put a rubber duck on it?
View 3 Replies View RelatedWe currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
i have two 1262 one is join ok but one join loop
View 7 Replies View Related