Cisco Wireless :: Converting A 1260AP From Autonomous To Light Weight Mode
Jan 17, 2013
Is the process for converting 1260 APs to lightweight mode any different from converting 1140s or 1250s? I've converted several APs to LWAP mode but this is my first 1260. Four 1260s need to be converted.I have one in a remote location that seems to be comatose. Here are the steps I took to convert the AP. Did skip/miss a step?
1. uploaded code to the AP ap3g1-rcvk9w8-tar.152-2.JB.tar
2. configured the AP for DHCP. It successfully leased a DHCP address. Controller information is provided via DHCP Option 43.
3. saved the configuration
4. verified the code, successful
5. disabled wireless radios
6. installed the lightweight code using the command archive download-sw /safe flash:/ap3g1-rcvk9w8-tar.152-2.JB.tar.The installation was successful
7. rebooted the AP
After that nothing. The AP has not leased another IP address. The switchport is active. The APs MAC address is registering in the switches MAC address table. The AP is receiveing PoE from the switch. I noticed that this AP is only receiving 6.2W of power where the three are getting anywhere between 8.8W and 9.3W. I am unable to ping the old static IP of the AP too.
View 4 Replies
ADVERTISEMENT
Mar 19, 2012
I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies
View Related
Jan 15, 2013
I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .
View 1 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Apr 30, 2012
My access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies
View Related
Jan 13, 2013
I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
View 31 Replies
View Related
May 17, 2012
I have an AIR-LAP1142 that I'm trying to load the autonomous software onto. I reset the AP with the mode button held down as per instructions. When I release, it attempts to download c1140-k9w7-tar.default from my pc running tftpd62. Several connections are made and then it eventually times out. I tried another machine (also win7 x64) and it fails there too exactly the same.
TFTP logs show:
Connection received from 10.0.0.1 on port 1024 [18/05 17:22:04.269]
Read request for file <c1140-k9w7-tar.default>. Mode octet [18/05 17:22:04.270]
Using local port 51686 [18/05 17:22:04.270]
[Code].....
View 3 Replies
View Related
May 29, 2012
Recently, our company wireless AP 1262 connected more than 40+ clients, and sometimes the wireless access speed is too slow. those clients are only for MES data transfer, the date no more than 10K of each stations. So I'd like to know if the one AP can support the network traffic if whole testers transfer the data to Database via this wireless AP1262? and the WLC no clients roaming option for which clients can connect to another AP around. I have checked the WLC and AP configuration. no option for clients roaming to another APs, do you know how to configure this AP's Clients move to another APs?If we setup the new APs in the location, does the clients will be auto connect to this new AP?
View 7 Replies
View Related
Feb 19, 2013
I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
View 28 Replies
View Related
Oct 5, 2011
I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies
View Related
Feb 26, 2013
I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
View 2 Replies
View Related
Jan 11, 2012
One of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi. Basically they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
- Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
- Set Ap-Manager Interface parameters
- Virtual Interface parameters
- Set Admin Credentials
- Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
- Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
- Configure Wlan Auth for Corporate/Guest Wifi
- Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.It appers that the IT guy of my customer tried to configure one of the Ap.In that Ap's flash i find files referring to a "mesh" configuration like: [code]
View 11 Replies
View Related
Feb 21, 2013
When I tried to download software for WLC44xx, I noticed both mesh and standard software releases. Do I need to keep seperate controller for mesh APs?.
WLC with standard sw can not handle mesh APs?
View 6 Replies
View Related
Feb 11, 2013
At the present, we have two WLCs (5508). There are a total of 84 LAPs (1242AG). One controller is configured as the master controller in which all our APs associate to. It's currently running software version 7.0.116.0 and some of our BYODs using Windows 8 are unable to connect to the wireless. The fix for this is to upgrade the software of the WLC so that the LAPs can obtain the update to solve this problem. Simple! However, before rolling this out into the production wireless network, I would like to test it out on our second WLC which has no LAP associations, a test WLAN configured, and a newer software image loaded (7.4.100.0). I have a spare LAP that was previously associated with the master controller running the same software version (7.0.116.0). What I'm looking to do is associate this LAP to the 2nd WLC instead of the master so that I can ensure that the LAP gets the newest software. Then, I would like to test a Windows 8 device to make sure it connects.So far, I have done the following:
1. Disabled the 1st WLC from using Master Controller Mode and rebooted AP - result was unsuccessful; still associated to 1st WLC.
2. Reset LAP configuration excluding static IP info and reset AP - result was unsuccessful; still associated to 1st WLC.
3. Compared config for both WLC but since I'm new to these devices, I'm not sure what needs to be configured/changed.
View 4 Replies
View Related
Nov 3, 2011
I have been installing Light Weight AP's and these make LMS device discovery take much longer because they are found via CDP but do not run SNMP. So you suffer the SNMP retry and wait time for each one which adds up with several hundred AP's. I added the CDP platform description they announce via CDP to system-config.xml but this didn't do the trick. I have updated system-config.xml successfully in the past to add ATA's and 7936 conference phones and this stopped discovery from processing these devices. So I was surprised when this didn't work for LW AP's. The CDP platform of the AP's looks like this (from show cdp n):
Platform: cisco AIR-CAP3502E-A-K9 , Capabilities: Trans-Bridge
So you can see cisco is all lower case and there appears to be spaces at the end before the comma. I thought the spaces might be the problem so I added them in system-config.xml but this didn't work. When I display system-config.xml with the XML editor in IE it does not show spaces at the end even though they are their when I look at the file with notepad. When I enable debug for discovery it shows these being added to the bypass table for CDP discovery but it still tries to process them. This is LMS 3.2 on Windows Server 2003. I use the CDP module for discovery.
View 6 Replies
View Related
Sep 12, 2012
We have a WLAN consisting of a WLC 4402 and 11 lightweight APs. For security/compliance reasons we have a Cisco PIX firewall that sits between the WLC (outside) and the APs (inside). The APs are allowed to form LWAPP tunnels through the firewall (inside access-list) to the WLC and the WLAN works as expected.The firewall then limits traffic from the WLAN (outside access list) to certain the internal systems.I have noticed that every so often the firewall logs show continuous "Land attack from 0.0.0.0 0.0.0.0" messages then all APs are disconnected (all lights flash).
View 2 Replies
View Related
Sep 4, 2012
I have configued Cisco LAP 1242AG with statis IP.I have connected LAP to WLC.I am able to ping WLC management interface IP Address from LAP's console.LAP is failed to Join WLC with error "Could not resolve CISCO-SAPWAP-CONTROLLER"
View 3 Replies
View Related
Mar 4, 2012
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies
View Related
Aug 13, 2006
i need to change the IOS in a Ligthwiegth Access point and make it work as an Autonomus AP 1242. I have got the image but im not realy clear about the process. I got to enter the Ligthwiegth Access point true the console port but i dont know how is the upgrading process.
View 6 Replies
View Related
Mar 28, 2012
We purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey. however i haven't come across much online for instructions. i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.
View 11 Replies
View Related
May 5, 2011
I’m configuring a Cisco 1142n AP in autonomous mode. The networking part is successfully working, multiple VLANs, SSIDs etc. I would like to configure one of my wireless networks to work with WAP2-PSK and the other with WPA-PSK.I’m confused as to what encryption to set on each radio and the ciphers to use on the SSID for each vlan to enable the best possible security. I’m not using a RADIUS sever in my network .point me in the right direction with the right CLI commands?
View 12 Replies
View Related
May 7, 2013
i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
View 20 Replies
View Related
Mar 8, 2012
we had a problem with a customer wlan in our warehouse (cannel overlapping). The troubleshoot needed a long time. For the future if requipred in case of problems i want to configure one access point in the warehouse as a scanner (please find picture in the attachement). The Autonomous cisco 1242 is now configured as scanner but i can't see any logfiles? Where can i find these informations. This is the cisco description of the scanner mode:Scanner—Functions as a network monitoring device. In the Scanner mode, the access point does not accept associations from clients. It continuously scans and reports wireless traffic it detects from other wireless devices on the wireless LAN. All access points can be configured as a scanner.
View 1 Replies
View Related
May 15, 2011
I am configuring a mobile van that is used for a mobile health clinic to drive to several locations and when pulling into an allocated parking spot the van will connect via wireless automatically. I am using autonomous 1252 AP's and am considering either briding or workgroup bridging.
The issue I am encountering is that the AP inside a van is a router that has to do DHCP across the wireless and because the ethernet interface between router and AP in the van never goes down the router does not know to re-DHCP. I remember from way back there was an IOS command to track a serial interface and drop the ethernet if the serial link goes down. Is there an equivalent command for AP's to drop the ethernet interface if the radio interfaces go down?
View 2 Replies
View Related
Feb 25, 2012
how to downgrade/upgrade AIR-LAP1142N-N-K9 access point to autonomous mode, because i don't have controller. i'm not able to login to access point as its in Leightweight mode.
View 4 Replies
View Related
Apr 2, 2012
I have successfully converted my lap1242ag-c-k9 to autonomous mode. But when i try to set ssid or wep then hit apply it won't the changes i made.
View 3 Replies
View Related
Mar 16, 2013
configuration of a 1310 that will be a root access point and connected to wlc 4402. The AP will be implemented as autonomous and not lightweight.
View 3 Replies
View Related
Nov 1, 2011
I have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.
On CLI console i am seeing repeated constantly such entries:
*Mar 1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
[Code].....
( i have new firmware but how to upload it without this interface running ? )
View 16 Replies
View Related
Apr 20, 2012
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies
View Related
Apr 25, 2013
I am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
View 1 Replies
View Related
Mar 13, 2013
we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies
View Related
May 13, 2013
Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies
View Related
Feb 4, 2013
What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies
View Related
