Cisco Wireless :: Aironet 1260 Series MAC Filtering In Autonomous Mode
May 13, 2013Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: How To Setup A Standalone Aironet AP 1260 Series
Sep 13, 2011I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedCisco Wireless :: Aironet 1260 Series - Sending Station Has Left BSS
Oct 29, 2012We have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.
View 1 Replies View RelatedCisco Wireless :: Aironet 2600 Series AP AIR-CAP2602E To Autonomous
Jan 27, 2013I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View RelatedCisco Wireless :: LWAPP Mode To Autonomous Conversion Aironet 1262
Mar 13, 2013we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies View RelatedCisco Wireless :: Aironet 1250 AIR-LAP1252AG-A-K9 - Change To Autonomous Mode
Jun 11, 2013I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
Cisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences
Jul 24, 2012What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedCisco Wireless :: Configuring A 1260 Autonomous AP Documentation?
Mar 5, 2012good docs for configuring a 1260 autonomous AP?
View 1 Replies View RelatedCisco Wireless :: Aironet 1260 As Bridges?
Feb 2, 2012Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
Cisco :: AP 1260 Autonomous With WPA2-PSK And MAC Filter
Feb 28, 2013I have two Cisco 1260 autonomous access point setup with WPA2-PSK. They are up and running. In that configuration it is Personal security since the security is only provided by the shared key. I'd like to add MAC filtering so in my open authentification I just scroll down to "with MAC filtering" and save. Doing that crash everything and switch to Enterprise security which need to have a Radius server (the shared key is not saved anymore and by using a device I now see 802.1x security).
View 1 Replies View RelatedCisco Wireless :: Aironet 1260 Access Point Work Without Controller??
Dec 1, 2010I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies View RelatedCisco Wireless :: Is Aironet 1260 Good For Indoor LWAP Or CAPWAP Environment
Jul 12, 2012Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies View RelatedCisco Wireless :: AP 1041 Conversion From Autonomous Mode To Lightweight Mode
Mar 4, 2012We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies View RelatedCisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series
Mar 6, 2012Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedCisco :: Aironet 1260 WDS Setup?
Jan 23, 2013I was wondering if its possible to setup the Cisco Aironet 1260 as a WDS master with radius and another Cisco Aironet 1260 as a slave for seamless roaming. How many slaves can a WDS master handle?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: AIRONET 1260 With New Radius ACS 4.x?
Nov 18, 2012I have CISCO ACS 5.1 radius for VPN on ASA and tried to configure an NDG on it for AIRONET 1260 too and worked fine with IEEE 802.1x CISCO EAP-FAST authentication As I had some trouble to let users to authenticate only on VPN if are VPN users and only on CISCO AIRONET if need only WIFI AIRONET I tried exception policies rules but something not working. VPN was ok but not WIFI access denied for rule policy access I decided to install CISCO ACS 4.x on Windows 2003 that is on ACS 5 DVD I created NDG as done on ACS 5 put a shared secret , put on AIRONET too as done for ACS 5 but I receive an error against ACS 4.x To troubleshout it I tried [URL] but not work ! I think to have done all fine owever on ACS 5 it worked in 5 minutes I searched log inside ACS 4 and found "Invalid message authenticator in EAP request" and I found this: [URL]Changed shared secret more times but ever not workign with ACS 4 I need to have user and password prompt on client trying to authentincate on AIRONET WIFI and I need ACS INTERNAL USER no active directory, no LDAP , no external user database?
View 1 Replies View RelatedCisco :: Aironet 1260 Authentication Server
Sep 13, 2012I have 3 Aironet 1260's with the same SSID and set with Open Authentication with MAC Authentication. Can I designate one of the 1260's as the MAC Authentication Server? I have all 3 now working with MAC Address Authenticated ty Local List Only and have to put the new MAC address in all 3.
View 3 Replies View RelatedCisco :: Make SSID Hidden Aironet 1260?
Mar 28, 2013We have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies View RelatedCisco Wireless :: WDS On Aironet 1042 Autonomous AP?
Jul 11, 2012i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
Cisco Wireless :: Convert Aironet 1310 Autonomous To LAP?
Apr 22, 2012Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies View RelatedCisco Wireless :: Does Aironet Autonomous 2600 Support WDS
Mar 20, 2013Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
Cisco Wireless :: Aironet 1600 - Standalone Or Autonomous
Mar 18, 2013It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies View RelatedCisco Wireless :: Aironet 3602I-K9 - How To Change To Autonomous AP
Mar 25, 2013I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
Cisco Wireless :: Making Aironet 1140 Autonomous?
Nov 6, 2012The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies View RelatedCisco Wireless :: Aironet 1250 LWAPP To Autonomous Downgrade?
Aug 25, 2010upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedCisco Wireless :: Aironet 1142N Autonomous / 15.2.2-JA Firmware Upgrade?
Sep 6, 2012We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
Cisco Wireless :: 1130AG Series - AP In Autonomous Supported Model?
Feb 16, 2013what are the series of access point that are supported without WLC. anteena should be in built and capability link 1130ag series.
View 9 Replies View RelatedCisco Wireless :: 1242 - Mode To Autonomous
Aug 13, 2006i need to change the IOS in a Ligthwiegth Access point and make it work as an Autonomus AP 1242. I have got the image but im not realy clear about the process. I got to enter the Ligthwiegth Access point true the console port but i dont know how is the upgrading process.
View 6 Replies View RelatedCisco Wireless :: Configure 3502e In Autonomous Mode?
Mar 28, 2012We purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey. however i haven't come across much online for instructions. i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.
View 11 Replies View RelatedCisco Wireless :: Configuring 1142n AP In Autonomous Mode?
May 5, 2011I’m configuring a Cisco 1142n AP in autonomous mode. The networking part is successfully working, multiple VLANs, SSIDs etc. I would like to configure one of my wireless networks to work with WAP2-PSK and the other with WPA-PSK.I’m confused as to what encryption to set on each radio and the ciphers to use on the SSID for each vlan to enable the best possible security. I’m not using a RADIUS sever in my network .point me in the right direction with the right CLI commands?
View 12 Replies View RelatedCisco Wireless :: Air-lap-1131-ag-e-k9 - How To Convert To Autonomous Mode
May 7, 2013i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
Cisco Wireless :: Autonomous 1242 In Scanner Mode?
Mar 8, 2012we had a problem with a customer wlan in our warehouse (cannel overlapping). The troubleshoot needed a long time. For the future if requipred in case of problems i want to configure one access point in the warehouse as a scanner (please find picture in the attachement). The Autonomous cisco 1242 is now configured as scanner but i can't see any logfiles? Where can i find these informations. This is the cisco description of the scanner mode:Scanner—Functions as a network monitoring device. In the Scanner mode, the access point does not accept associations from clients. It continuously scans and reports wireless traffic it detects from other wireless devices on the wireless LAN. All access points can be configured as a scanner.
View 1 Replies View RelatedCisco Wireless :: 1252 Autonomous AP In Bridge Or WGB Mode?
May 15, 2011I am configuring a mobile van that is used for a mobile health clinic to drive to several locations and when pulling into an allocated parking spot the van will connect via wireless automatically. I am using autonomous 1252 AP's and am considering either briding or workgroup bridging.
The issue I am encountering is that the AP inside a van is a router that has to do DHCP across the wireless and because the ethernet interface between router and AP in the van never goes down the router does not know to re-DHCP. I remember from way back there was an IOS command to track a serial interface and drop the ethernet if the serial link goes down. Is there an equivalent command for AP's to drop the ethernet interface if the radio interfaces go down?
