Cisco Infrastructure :: Converting WS-C3560G Switch To DC Power?
Apr 15, 2013What needs to be done to convert a WS-C3560G-24TS-E to DC power?
View 2 Replies
ADVERTISEMENT
Cisco Infrastructure :: 3550 - Limiting Power Allocation To 15.4 W On Pre-POE Switch?
Jan 2, 2013I'm using a Catlyst 3550 to supply power to a IP network surveliance camera. By default, the predecesor to POE, Cisco Inline Power allocates 15.4 W of power to a port ... What is the process for reducing this power output?
"For an IEEE device, the switch always allocates 15.4 W to the port. The switch does not display the IEEE class type in the show power inline privileged EXEC command output. Instead, it displays n/a."
Cisco Infrastructure :: 2960s / 3750s / 6506 - AC Power Outlet On Catalyst Switch
Apr 15, 2011I have several 2960s and 3750s and two 6506 (ws-cac-3000w) recently move to new location The power outlet is the same ,but Volt is different current 2960/3750 use this(one phase 3 wire) 220v and new location change to (from 3 phase 4 wire -> one phase 220v)6506 current using(one phase 3 wire) and will be change to (from 3 phase 4 wire -> one phase 220v)
I had search doc about power supply /cable , only show support single phase 220 v ,but not description vlot between each wire !!Does new location power outlet suit for 2960/3750s power and 6500 ws-cac-3000w ?!? Do I need chane power outlet back to current using?
Cisco Switching/Routing :: WS-C3560G-48PS-S Power Cord
Nov 23, 2011I need to prepare a Bill of Material for WS-C3560G-48PS-S switch.
Whether we should go for CAB-AC-JPN - AC power cord for Japan OR CAB-AC-ACE AC power cord for Europ
Cisco Switching/Routing ::WS-C3560G-48PS - IP Phone Gets Restart While Power Fluctuate
Jun 21, 2011We are using WS-C3560G-48PS connected via UPS power supply. Whenever raw power supply gets fluctuates few of the IP phones (Alcatel) gets reset although switch is remain up and running. We checked the same by disconnecting the raw power supply but we didn't found any packet loss from the node which are connected through this switch. But few IP phone gets reset. What could be the reason
View 2 Replies View RelatedCisco WAN :: C3560G-24TS Switch Shuts Down?
Feb 23, 2011I have a Cisco C3560G-24TS Switch that has twice now just shut down and the only way to get it back to life is to pull the power and let it boot back up again.
Are there any logs I can check for poss clues as to why this is happening or any other things I can try?
Cisco Switching/Routing :: Which Ios Will Support IPv6 Feature In WS-C3560G-48TS Switch
Feb 18, 2013I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedCisco Switching/Routing :: WS-C3560G-24PS - Checking Utilization And / Or Performance On Switch
Apr 23, 2012I have a WS-C3560G-24PS service as a distribution switch with six (6) WS-C2950T-24 connected to it. In looking at the utilization on the inter connect links no one is running close to a gig speed and this includes the link between this switch and the core. The CPU load (6%) and memory utilization (30%) on the switch do not seem bad so what else does one watch to see if it needs an upgrade?
We are starting tohave discussions about any needed upgrades on the network. I have an ocassional user that complaines about low performance but looking through the network I can find nothing glaring on a consistent basis that says an upgrade is warranted. I am however looking at things such as the above. Utilization on links, CPU, memory, etc.
Cisco Infrastructure :: NM-32A Card Power Consumption?
Jan 17, 2013what is the NM-32A card power consumption?
View 2 Replies View RelatedCisco Infrastructure :: 3600 With Power Connector But Do Not Have RPS
Nov 4, 2012I have a router 3600 with a power connector kind RPS but I don't have a RPS system, Do it exist a kind of wire that I can connect directly from my router to AC?
View 1 Replies View RelatedCisco Infrastructure :: Power Consumption Of C3750X And C3560X
Oct 16, 2012I am finding the power consumption of WS-C3750X-24T-L, WS-C3750X-48T-L, WS-C3560X-48T-L and WS-C3560X-24T-L switches?
View 5 Replies View RelatedCisco Infrastructure :: Running A 4507 With Power Supplies
Jun 9, 2011I am running a 4507 with the Power Supples PWR-C45-2800ACV. url...
Can I plug this power supply into this UPS unit? url...
Cisco Infrastructure :: Is GLX Compatible With 3750G-24PS Switch
May 23, 2011I am trying to buy a GLC-SX-MM SFP module via Fed Stock, and I keep getting a GLX-SX-MM. What is the difference between these two part numbers? I can't find it on the Cisco Web site and eve a search of Google comes up relatively fruitless! Is the GLX compatible with my 3750G-24PS switch?
View 2 Replies View RelatedCisco Infrastructure :: Finding Replacement For Switch C4006?
Oct 3, 2012Right Now we are using Cisco switch model c4006.and we are looking to replacement for the same . Below are our requirements.
1: Around 120 Ports (100 Mbps)
2: Around 30 Ports (1Giga)
3: Layer2/Layer3
Cisco Infrastructure :: 3524xl-EN Switch Not Displaying Any Output
Oct 6, 2012I have 2 cat3524xl's and a 3550. I recently did something to the IOS that makes the switch not display any output to the console port. Not sure what I did but even doing the reset as instructed in the Cisco docs by holding the mode button foe 2 seconds after boot. I get the flashing green light but still no output. All POST tests pass according to lights so I tried different cables and all baud rates with no change. I hoocked switches back up in lab and can see them in CDP neibors but do not know how to access them from there as they have no IP assigned to them. Remember this is two of them with exact same issue.
View 2 Replies View RelatedCisco Switching/Routing :: Add SMB SF300 - 24 Switch To Infrastructure
Nov 18, 2012I am trying to add a Cisco SMB SF300 - 24 Switch to an infrastructure which has only Cisco Catalyst Switches The Core layer is Cisco Cataylst 4503 . Distribution is Cisco Catalyst 3560 and the Access Layer is Cisco 2960 Switches.There about 30 VLANs present in the infrastructure which is advertised to all switches using VTP. Inter VLAN routing is done at the Core Switches by creating Interface VLANs for every L2 VLAN.
1. The new VLAN 150 needs to be created on the new Cisco SMB Switch. If I create a corresponding interface VLAN 150 on the Core Switches , will it route traffic to other VLANs just like it is currently working for Cisco Catayst 2960 Switches ?
2. Upon checking I could see that VTP is not supported on Cisco SMB Switches and I would need to go for GVRP if I need to advertise VLAN information to other Switches. But since GVRP is supported only on CatOS and there is no inter operability between GVRP and VTP , I would need to create VLANs manually on the new Switch . Is that correct ?
Cisco :: Manage Switch SMB 300 Series Using Prime Infrastructure 1.2?
Mar 3, 2013Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
View 1 Replies View RelatedCisco Infrastructure :: Use HWIC-4ESW As No Switch Port?
Oct 4, 2012Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies View RelatedCisco Switches :: 3750 / SMB Switch Integrations With Non-SMB Infrastructure?
Jul 27, 2011A customer is expanding their network into another wing, and they have a good number of existing Small Business switches (specifically the SGE-2010P - [URL] that they're interested in possibly deploying. They have a full-blown Cisco infrastructure and voice deployment (Cat 6500 core switches, 3750 switch stacks, Communications Manager w/ over 1,000 phones, etc.).
The general concern is whether there is ANY known issues or concerns with trying to mix/integrate the Small Business equipment with non-SMB infrastructure. Looking at the datasheet for this switch, it's clearly PoE, supports QoS, although it doesn't specifically indicate it can provide a voice/auxiliary VLAN for a phone detected by CDP - that would be a big deal. So basically, "a switch is a switch", and I'm just posing this question to make sure there's no reason (technically or from a support standpoint) that we would not recommend integrating these.
Cisco Infrastructure :: 2811 Router Is Sitting Behind 3650 Switch?
Jul 9, 2012Seeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies View RelatedCisco Infrastructure :: No Icmp Reply From Catalyst 2950 Switch
Nov 15, 2005My switches is still operating but when i ping the switch, there isn't any reply. No icmp reply from catalyst 2950 switch
View 6 Replies View RelatedCisco Infrastructure :: 1841 / 2960 Switch - Temperature OID Needed
Jan 24, 2012I need the temperature oid for cisco 1841 and 2960 switch.
View 1 Replies View RelatedHow To Switch Power Off On Router
May 29, 2011I am dealing with cisco networking and am using cisco packet tracer bt i want to configure router but when dragging modules (ports) it tells me you cant drag modules when power is on
View 1 Replies View RelatedCisco Infrastructure :: Route Internet Traffic To Different Gateway Using 3560G Switch
May 24, 2011My issue: I have installed a firewall within my network. Currently all my clients default gateway defaults to GW:192.168.1.1. I would like all my internet traffic to route to the firewall ip 192.168.1.30. My Primary switch ip is 192.168.1.10, which is a 3560G running 12.2(25)SEE2 IPBASE-M.
My main problem is, I do not have access to the gateway, so I am trying to route internet traffic from within my switch to the firewall. I have already tried Route-Map, but seems this version of the OS does not support. I have already tried Policy-Map, but same as above. I have also tried IP ROUT command, but it did not work either.
And remember, I would like to perform the routing from the switch, because I do not have access to the default gateway which is a router to perform forward internet traffic to the firewall.
Cisco Infrastructure :: Temperature Status From 2960 Switch Using SNMP Not Working
Sep 18, 2012WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Cisco Infrastructure :: Blocking ICMP On Catalyst 3750 Switch Vlan?
Apr 7, 2011I have set up an ACL on my 3750 switch to deny icmp from PC A on our inside network to PC B on a different VLAN on our inside network using the following ACLs:
deny icmp host 10.1.17.15 host 10.3.10.4
deny icmp host 10.3.10.4 host 10.1.17.15
-- or --
deny icmp host 10.1.17.15 host 10.3.10.4 echo-replydeny icmp host 10.3.10.4 host 10.1.17.15 echo-reply
These ACLs belong to an access-list that also limits ip traffic to a few specific machines.When I try pinging from PC A I receive a reply message back from PC B. Shouldn't this configuration block any ICMP from PC A to PC B and from PC B to PC A? I would have expected the first ACL statement to block any packets associated with ICMP and when that didn't work I tried the second configuration.
Cisco Infrastructure :: Catalyst 4006 - Enable Http Login To Switch?
Apr 12, 2005Is it possible to enable login by http (web interface) to catalyst 4006 switch with WS-C4006 Software, Version NmpSW: 6.3(5) ?
View 21 Replies View RelatedCisco Infrastructure :: 2008r2 - Switch Can Upload To FTP But Not Download (protocol Error)
Apr 18, 2013I have windows server 2008r2 running a FTP server, so I can back up my configs and upgrade IOS when needed. My problem is than I can backup to the server just fine but when i try and restore a config or pull a new IOS over it gives me this error
%Error opening ftp://13****** (Protocol error) this is happening on every switch I have and I can't figure it out.
Cisco Infrastructure :: 3750-48PS Switch Stack Unable To Boot?
Aug 25, 2012I have been experiencing a strange problem i have a switch stack of 3750 in which 4 switches are cascaded. there is one one switch shows PROVISIONED status when I run "show switch". i have verified the stack cable connectivity its OK.
now when i try to console that particular switch i am unable to access it as well. I tried to reboot that switch and on reboot it only shows one LED syst blink once and after that remains constant and nothing happens to other LEDS. from the back of the switch FAN is working fine.
Cisco :: Switch Power Usage On Boot?
Oct 11, 2011I have a customer who is concerned with the power draw on the new switches we're deploying.They only have 20 amp breakers in their closets and fear popping them on switch boot. The customer is under the impression that a switch will pull full power on boot. So a 3560X with an 1100w PSU will draw the full 1100w on startup. Ive never heard this and it doest make much sense to me, but I need to verify.
View 10 Replies View RelatedIP9258 Web Controlled Power Switch?
Jan 30, 2012In the Power Schedule section, when I input my desired date and time to turn a socket on and off, the settings do not stay. It reverts back to the preset date from the manufacturer after I submit.
View 1 Replies View RelatedCisco Infrastructure :: High CPU Usage / Dropped Packets - Switch Blade WS-CBS3120X-S
Jun 25, 2012I have a couple of Switches Blade 3120, working as active-standby model (HSRP) on a new site deployment. There are other 20 sites more or less, working on the same model, without issues. But in this one, we are seeing a high cpu usage. The traffic going through the platform is 600Mbps (on peaks), and in this case we have 40% of CPU usage. Traffic should be close to 3 Gbps. When we tried to send the whole traffic through the platform, active switch began to drop packets on the majority of interfaces.
When we analyze the CPU usage, there is a special process called "HL3U bkgrd proce" always have the most CPU use, but we do not know what concerns. We do not know if it is caused because there are PBRs configured. It should not matter. How I mentioned, there are other sites working fine and have had always the same PBR number.
What is causing the high usage?. Is there a special debug we could to perform to diagnose the issue?. Also, we have seen a high interrupt CPU usage (9% in this case).
bog-sib-INT-rtr-1#show processes cpu sorted 5sec
CPU utilization for five seconds: 30%/9%; one minute: 25%; five minutes: 23%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
Cisco WAN :: Power Requirement For 3845 With Two (2) Switch Modules
Aug 17, 2011I would like to know if any additional power would be needed for a 3845 (currently with one (1) NME-XD-48ES-2S-P) to which another 24-port switch module is added. Thus, I would have two (2) switch modules on the 3845 for a total of 72 ports.
I have been unable to find specific power requirements detailing the requirements with 1 ethernet module, 2, etc.
