Cisco Infrastructure :: Running A 4507 With Power Supplies
Jun 9, 2011I am running a 4507 with the Power Supples PWR-C45-2800ACV. url...
Can I plug this power supply into this UPS unit? url...
ADVERTISEMENT
Cisco Switching/Routing :: 3750 - Power Stack Has Unbalanced Power Supplies
Jun 9, 2013I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
Cisco WAN :: 6509-E With Redundant Power Supplies (WS-CAC-3000W) But One Is Non-operational
Feb 10, 2010I have a 6509-E with redundant 3000W power supplies (WS-CAC-3000W) but one supply is current non-operational.From the outputs I'm not sure whether the issue is (more likely to be) with the supply to the PSU or the PSU itself, i.e. whether my first action should be to get an electrian to check the supply or fault call the PSU with our maintenance providers and have it replaced?
View 3 Replies View RelatedCisco Switching/Routing :: Power Supplies In Stack With 3750X
Mar 12, 2012I have two WS-C3750X-48PF-S in stack, but every one has just one power supply. In the package of the switches is included one stack power supply cable.does it make sense to use stack power cable if every switch has just one power supply ??
View 6 Replies View RelatedCisco Switching/Routing :: 3560X 24P-S Power Supplies Interchangeable?
Sep 12, 2012Are the power supplies on these switches interchangeable? I know the model numbers are the same with the exception of the /2 at the end if it. Customer wants it to have a dual power supply but not sure if I need to order a secondary powere supply or just another powere supplu from a spare switch.
View 1 Replies View RelatedCisco Switching/Routing :: Can Mix Power Supplies Of Different Wattage On 6500
May 14, 2012I have 6500 core switch with 2500W power supply, and I want to install a second power supply with 3000W ? is this applicable ? if yes, is there a specific configuration that must be done ?
View 4 Replies View RelatedCisco :: 3945 Router Power Supplies Load Balanced By Default?
Dec 5, 2012CISCO 3945 Routers - Are the 3945 Router power supplies load balanced by default? We are trying to determine if our switch/server rack at our remote location has maxed out it's power load requirements. I just need to know if the 3945 power supplies load balance by default or if the redundant power supply is ON but not really providing the router with power and is just there incase the other power supply fails .
View 3 Replies View RelatedCisco Switching/Routing :: Upgrading Catalyst 4500 Power Supplies?
Sep 19, 2012If I'm upgrading dual redundant power supplies in a Catalyst 4507 from 1000W (data) to 1400W (data), can it be done without taking the switch through a power cycle? I'm guessing no as I read that the switch will not recognize a 1400W PSU in bay 2 if there is still an original 1000W PSU in bay 1.
View 2 Replies View RelatedCisco Switching/Routing :: 3phase Or Single Phase Wiring For Nexus 7010 Power Supplies
Jul 26, 2010We just purchased a Nexus 7010 switch and we are at a stand still with our COLO trying to figure out what power source should be provided. APC recommends a 50amp 3phase vertical cabinet PDU (AP7867). What type of power sourcereakers will be sufficient in handling the Nexus 7k /w (3) power supplies? Do the COLO need to provide single phase or 3 phase power recepticals?
View 7 Replies View RelatedCisco Infrastructure :: WCCP Configuration On 4507
Jun 16, 2012I am trying to setup WCCP on our 4507. For some reason I cannot get this to work! The config I have tried is below. I can't figure out
ip wccp web-cache group-list IRONPORT-GROUPLIST
ip wccp source-interface GigabitEthernet2/24
!
Interface Vlan160
[Code].....
Cisco Switching/Routing :: Catalyst 4507-R Running 15.1.2 - High CPU Utilization
Feb 11, 2013we have 2 catalyst 4507 Switches (Catalyst 4507-R running 15.1.2.release) configured in VRRP and vlans are distributed across both the switches.For few vlans core1 is master and for remaining vlans core2 is master.Both cores showing different CPU utilization.when we did our troubleshooting,we realized that the server vlan on core1 (Core1 is master for this vlan) is creating high utilization.when we switched this server vlan to core2 the core1 utilization came down and core2 utilization increased.we identified that server vlan is culprit in this issue. i would like to know weather any method is available in core switch wherein i can check which server in this vlan is contributing for this utilization.(To identify the server which contribute this utilization,we can actually shut 1 server each at time to see weather utilization is going down.with this kind of testing ideally we should be able to identify the server but this will disturb the server environment which we don't want in live environment)
View 8 Replies View RelatedCisco Infrastructure :: Swap Fan In 3845 While It Is Running?
Oct 4, 2011Can you swap fan in 3845 while it is running?
View 1 Replies View RelatedCisco Infrastructure :: NM-32A Card Power Consumption?
Jan 17, 2013what is the NM-32A card power consumption?
View 2 Replies View RelatedCisco Infrastructure :: 3600 With Power Connector But Do Not Have RPS
Nov 4, 2012I have a router 3600 with a power connector kind RPS but I don't have a RPS system, Do it exist a kind of wire that I can connect directly from my router to AC?
View 1 Replies View RelatedCisco Infrastructure :: Power Consumption Of C3750X And C3560X
Oct 16, 2012I am finding the power consumption of WS-C3750X-24T-L, WS-C3750X-48T-L, WS-C3560X-48T-L and WS-C3560X-24T-L switches?
View 5 Replies View RelatedCisco Infrastructure :: Converting WS-C3560G Switch To DC Power?
Apr 15, 2013What needs to be done to convert a WS-C3560G-24TS-E to DC power?
View 2 Replies View RelatedWRT54G Running Just CAT 5e Cable Is Much Easier Than Having To Supply Power
Oct 2, 2012I am looking to upgrade my home wifi from a Linksys WRT54G running DD-WRT to something that will handle .11n. I've been looking at the Unifi PoE APs. Their base model support N, but only on 2.4GHz, and only has a 100Mb port. I was concerned about that being a limiting factor. They've recently released a new line that supports Dual Band and has a Gig port, but it cost about 4 times as much. Here are my goals:
1.) PoE if possible. Currently the AP is my rack in the basement. I'l thinking of running an additional cable to somewhere central on the first floor and putting the AP there for better coverage/signal. Running just a CAT 5e cable is much easier than having to supply power as well. Second thought was to get two Unifi APs and setup a mesh with roaming, which it looks like they support, for best coverage. In that case I'd put one in a top floor room that already has CAT 5e.
2.) I'd really prefer access points to a router. I already have a pfsense box that does the routing. If this means getting something that will run DD-WRT, Tomato, or the like and turning it into an AP fine.
3.) I would like something that is dual band .11n.
4.) Something that support RADIUS
5.) Multiple SSID support and VLAN support. I want to be able to offer at least 2 separate networks.
So am I stuck buying the Unifi dual band AP? Or should I get something like the Asus RT-N66U and put Tomato on it?Does anyone have acutal expreience with the Unifi products?
Cisco Infrastructure :: 3550 - Limiting Power Allocation To 15.4 W On Pre-POE Switch?
Jan 2, 2013I'm using a Catlyst 3550 to supply power to a IP network surveliance camera. By default, the predecesor to POE, Cisco Inline Power allocates 15.4 W of power to a port ... What is the process for reducing this power output?
"For an IEEE device, the switch always allocates 15.4 W to the port. The switch does not display the IEEE class type in the show power inline privileged EXEC command output. Instead, it displays n/a."
Cisco Infrastructure :: 2960s / 3750s / 6506 - AC Power Outlet On Catalyst Switch
Apr 15, 2011I have several 2960s and 3750s and two 6506 (ws-cac-3000w) recently move to new location The power outlet is the same ,but Volt is different current 2960/3750 use this(one phase 3 wire) 220v and new location change to (from 3 phase 4 wire -> one phase 220v)6506 current using(one phase 3 wire) and will be change to (from 3 phase 4 wire -> one phase 220v)
I had search doc about power supply /cable , only show support single phase 220 v ,but not description vlot between each wire !!Does new location power outlet suit for 2960/3750s power and 6500 ws-cac-3000w ?!? Do I need chane power outlet back to current using?
Cisco Switching/Routing :: 2960S - Internal Power Supply Show Unavailing When Running Off RPS?
Feb 13, 2012I have a 2960S connected to an RSP 2300. The 2960S is currently running off of the RPS, and I would like to switch it back to the internal power supply. Can I just run "power supply 1 on"? Will this cause the switch to reboot? Also I am concerned because when I do a show env power it shows: [code]
Is it normal for the internal power supply to show Unavail when running off RPS?
Routers / Switches :: Wireless Only Supplies Half The House With Consistent Internet Access?
Jan 25, 2012My wireless router only supplies half the house with consistent Internet access. What's the easiest way to ensure connectivity throughout the house?
View 1 Replies View RelatedCisco WAN :: Running All Switches Running By Default Configuration And Connected To WS-C4506
Jun 11, 2013I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View RelatedCisco Firewall :: Configuration Migration From ASA 5540 Running 7.2 To 5525X Running 9.1
May 7, 2013I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies View RelatedCisco Switching/Routing :: Stack-power 3750x / FRU Power Supply Is Not Responding
Sep 4, 2012After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
Cisco Wireless :: 1252 - WCS Reports AP Draws Low Power - With Correct Power Injector
Jul 21, 2011I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
Cisco Switching/Routing :: WS-C3560-48PS-S Show Power Inline But No Power Available
Apr 14, 2013We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
Cisco Switching/Routing :: 6500 - Power-Redundancy Mode Combined And Power Fail
Feb 28, 2011I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
Cisco Switching/Routing :: 3750X Stand Alone Secondary Power Supply Act As Pool Of Power
Apr 4, 2012In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies View RelatedCisco Firewall :: ASA 5512-X - Automatic Power-on After Power Failure?
Dec 5, 2012how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View RelatedDell :: How To Enable Automatic Power-on After Power Failure On ASA 5512-X
Mar 3, 2013how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 12 Replies View RelatedCisco Switching/Routing :: How To Enable Ssh On 4507
Feb 14, 2012How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Cisco Switching/Routing :: 4507 - CPU Going At 50 To 60 Percent
Nov 19, 2012I am having a Cisco 4507 switch. The CPU on the switch is running between 50% to 60% constantly. To troubleshoot I collected some logs using debugs & show commands.
debug platform packet all receive buffer
show platform cpu packet buffered
debug platform packet all count
show platform cpu packet statistics
show processes cpu sorted | exc 0.00
show platform health
show platform cpu packet statistics
show platform health output shows the below process crossing the target value.
%CPU %CPU RunTimeMax Priority Average %CPU Total
Target Actual Target Actual Fg Bg 5Sec Min Hour CPU
Stub-JobEventSchedul 10.00 13.41 10 47 100 500 13 13 10 5462:52
K2PortMan Review 3.00 5.35 15 11 100 500 4 4 3 1799:47
What I need to know is, though these process are running in Low Priority, will there be any issue if the CPU goes high due to these process.
Cisco WAN :: High CPU (99%) Utilization Of 4507 Switch
Dec 21, 2011I am facing lots of issue with cisco 4507 switch recently.. Every alternate day, its CPU is getting utilized by 99% and network stopped working..finally it has to be restared.
Below is the CPU utilization of the process:-
------------------ show process cpu ------------------
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....