Cisco Switching/Routing :: WS-C3560G-24PS - Checking Utilization And / Or Performance On Switch
Apr 23, 2012
I have a WS-C3560G-24PS service as a distribution switch with six (6) WS-C2950T-24 connected to it. In looking at the utilization on the inter connect links no one is running close to a gig speed and this includes the link between this switch and the core. The CPU load (6%) and memory utilization (30%) on the switch do not seem bad so what else does one watch to see if it needs an upgrade?
We are starting tohave discussions about any needed upgrades on the network. I have an ocassional user that complaines about low performance but looking through the network I can find nothing glaring on a consistent basis that says an upgrade is warranted. I am however looking at things such as the above. Utilization on links, CPU, memory, etc.
View 2 Replies
ADVERTISEMENT
Feb 10, 2011
Just spoke to the TAC and didn't get the information needed. When configuring ip dhcp snooping database I am adding this to my configuration:ip dhcp snooping database scp://dhcpsec@192.168.1.50/home/dhcpsec/switch1.dhcp.database.txt..I assumed that to do this I would either specify the password on the command line, similar to the way its done when using ftp/http, or that I would need to create a public/private key.I have enabled scp and can manually copy a file from the switch to the linux server. So I believe I have all the aaa commands correct. Cisco WS-C3560G-24PS System image file is "flash:/c3560-ipservicesk9-mz.122-55.SE.bin".
View 3 Replies
View Related
Jan 14, 2013
I've been experimenting with the 'vlan dot1q tag native' command on a switch and it seems as though tagging the native vlan breaks vty access to my access point.With the 'vlan dot1q tag native' commnand applied, I lose management connectivity to the AP with 'no vlan dot1q tag native' applied, connectivity is restored. Why is this? Is it safe to say that one can access the AP via vty lines using ONLY untagged packets?
SWITCH
Model: WS-C3560G-24PS
Code: c3560-advipservicesk9-mz.122-46.SE
--Abbreviated CONF
vlan dot1q tag native
[code]....
View 14 Replies
View Related
Jun 14, 2011
I am not on site and I have not seen a WS-C3750V2-24PS-S. Customer has a stack of 6 x WS-C3750V2-24PS-S and one unit has failed. We do not have a WS-C3750V2-24PS-S spare. Can we replace it with a standard WS-C3750-24PS-S (not V2) switch and be part ofthe stack.
1. Are there any traps gotchas?
2. What about IOS versions - aren't they different for V2 switches
3. Are the stack ports and stack cables same for both WS-C3750V2-24PS-S and WS-C3750-24PS-S
4. What is the main reason for bringing out the V2 switches. What features do they have extra?
View 3 Replies
View Related
Jun 5, 2012
is possible to have WS3750G-24PS in one stack with WS-C2960S-24PS? I want to add two new WS-C2960S-24PS to stack with one WS3750G 24PS.
View 1 Replies
View Related
Jul 23, 2012
Can a C3560-24PS switch with 32 MB flash be loaded with IOS 15? Will it be able to execute the code and function properly?
View 2 Replies
View Related
Feb 18, 2013
I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies
View Related
Oct 19, 2012
In Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Sep 5, 2012
I have been facing High CPU Utilization issue with few of my Cisco 4006 Switches together from last one month. Out of which 1 switch issue sorted out auto after 2 days however the problem is still exists with rest 3 switches.They are 6-7 year old and having one SUP engine and other are switch port modules.
View 5 Replies
View Related
Dec 20, 2011
I am experiencing high cpu utilization in my 4000 series core switch.
I checked the loggs. i saw some strange loggs.
Please see the below logs:
Code...
What is the "invalidsourceaddresspacket" ?
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.
View 12 Replies
View Related
Feb 25, 2013
i am seeing very high utilization on a random basis on the stack. and the logs indicate me that there is a pattern where there is a stack power cable shows inserted (which was never unplugged) followed by sudden spike in the utilization.
001018: *Mar 6 16:21:22.138: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 4 stack power cable 1 inserted
001019: *Mar 6 18:18:37.982: %SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU
[Code]......
View 16 Replies
View Related
Feb 14, 2012
We had a core switch(30 vlans) in our environment and it's noticed that CPU utilization of the core switch is showing high during recent days. I have checked logs and processes, but couldn't find the root cause. The issue found only in the office hourly only(after that the cpu utilization is idle and normal). I have already referred the following link to troubleshoot the issue " [URL]
see the following outputs from the core switch
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 6687557041432420936 466 47.52% 47.10% 45.98% 0 Cat4k Mgmt LoPri
55 30667074884269560256 0 45.36% 45.50% 45.85% 0 IP Input
29 28552856922870089254 0 3.59% 3.50% 3.57% 0 Cat4k Mgmt HiPri
[code]....
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
My queries regarding the issues are following
1) How can we find root cause regarding the high cpu utilization?
2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?
View 10 Replies
View Related
Feb 14, 2012
We have a problem of igh CPU Utilization in Cisco 4510R-with dual SUP V-10G modules.
Cisco 4510R switch is the CORE switch and have 30 no's of VLans. It was running PVST/PVST+ previously. But Now we have migrated to MST. But after upgradation the CPU utilization reached alomst 98%.
View 2 Replies
View Related
Sep 3, 2012
We have Cisco ME3400 switch, with configuration described below.
GE0/1 port is uplink:
interface GigabitEthernet0/1
description ***MATED-IUB_C&U-Plan***
port-type nni
switchport trunk allowed vlan 331,450,4085
switchport mode trunk
GEo/2 is configured as below:
interface GigabitEthernet0/2
description ***From NIB***
port-type nni
switchport access vlan 4085
[URL]
We have also tried Loopguard feature enabled on all ports: but after some period same problem is repeated.
version information is below:
Cisco IOS Software, ME340x Software (ME340x-METROIPACCESSK9-M), Version 12.2(25)SEG3, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 25-Jul-07 22:56 by amvarma
View 8 Replies
View Related
Aug 16, 2012
In my network we use all cisco 2960 switches, problem is when someone copying 4gb data or high from one switch to another switch, by that time rto (Request time out) is coming.
router
|
|
|
[Code]....
1. when user 1 copy data from server ,at that time who is in switch2 behind like user2 ,he is getting problem like when ping to default-gateway,or rto is coming and network is very slow .
2. when i open sw2,sw1,sw3,trunk ports utilization is very high except sw4 to sw1 trunk ports,who behind sw4 like user4 ,he is not getting problem.
3.all switches trunkport in my network is faster ethernet and i have no option to connect trunkport to gigaehternet and ethernet channel.
View 2 Replies
View Related
Apr 25, 2013
I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies
View Related
Nov 8, 2011
I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies
View Related
Mar 5, 2013
I upgrade the IOS of my switch 3560 from C3560-IPBASE-M), Version 12.2(25)SEB4, To C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history
View 5 Replies
View Related
Jan 30, 2012
WS-C3750G-24TS-S1U switch stack with high CPU utilization. 3 switches are stacked and using PBR on that. I am attaching the show cpu process as an attachment.The current template is "desktop routing" template.The selected template optimizes the resources in the switch to support this level of features for 8 routed interfaces and 1024 VLANs. [code]
View 0 Replies
View Related
Mar 3, 2012
We have branches all over the country and we take different links like fiber (Ethernet) radio links etc. Now sometimes when we ping from branch WAN ip to its gateway or to the aggregation router (ASR 1000) in this case, we see some drops, but see no problem in actual HTTP or lotus communication.
What i want to know, that now a days, should we rely on ping results to determine link quality ? or should i use tools like iperf to basically see if the link is actually treating tcp and udp packets properly, I have heard this countless times that normally network devices like Cisco routers, even without any QOS, will give low priority to ping packets.
View 1 Replies
View Related
Nov 2, 2011
I want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies
View Related
Nov 6, 2011
I have WS-C3750-24PS version 12.2(55)SE4. I am configuring PBB VPLS. MY PE/P routers are alcatel 7710/7750
my topology is like that.
CE1<-------> Provider_switch(3750)<-------> PE1 < ----IP/MPLS----> PE2<-------> Provider_switch(3750)<----------->CE2
16 11 11
[Code].....
View 3 Replies
View Related
Jan 21, 2013
I have three new 2960 switches as listed in the title. I configured them as follows:
192.168.1.215 host: whse-c
192.168.1.216 host: whse-b
192.168.1.217 host: whse-a
Switches B and C flow into A before continuing on into the server room switch (distance issues).All three switches are configured for ports 21-24 at 1000 and set as cisco switches. all other ports are undefined as they have a myriad of desktops, printers and non cisco access points flowing into them. side question - should i configure them as access points where applicable even if they are non cisco? I am replacing three netgear switches that currently are in place and have no known issues other than they are old and the fans may fail soon.hooked up .217. was able to get to it from the network. Hooked up 215 and then 216. All the sudden I lost the ability to tap into the switches, any of them. (I think I had done 215 at that point too, before adding 216. I found out later it took the network to its knees as internet was lost, and the MPLS stopped functioning.
I undid the changes and put the netgears back in service and all was right with the world again. At first I thought it was a bad host name as I had used whse-a on switch C in error. I changed that after this issue.Later that day I put 215 in place. checked it from the network and could get to it just fine. Then I put 216 in service. I lost connection to 215. I could no longer get to the internet from my pc and the MPLS went down again. This time I just unhooked 216. 215 is still in place and working on the network at the moment and not causing issues. (btw these switches are not even in my path from my pc to the internet, just on the same network) tomorrow I am going to try 217 again while 215 is still on the network and see if there are any issues adding that swtich. if I can do so, and there are no problems, is this an indication of a faulty switch? what further testing can I do, have I missed something in setup? If this brings the network down again, why cant i add two of these switches to each other/on the same network path (B and C were not even connected to each other yesterday evening when it went down again).
View 2 Replies
View Related
Mar 7, 2012
This switch randomly reboots throughout the day. I checked the stacks info and reported it was using crashinfo_12 (report below). I have access to the switch throughout the day if more config info needs to exported.
Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE1, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code].....
View 1 Replies
View Related
Mar 11, 2013
3560 is running c3560-advipservicesk9-mz.122-40.SE. The SFP (GLC-TX) has been tested in another 3560 and is recognized. Both the gi0/1 and gi 0/2 ports show the type as unknown.
Port Name Status Vlan Duplex Speed TypeGi0/1 notconnect 1 auto auto unknownGi0/2 notconnect 1 auto auto unknown
View 2 Replies
View Related
Nov 23, 2011
I need to prepare a Bill of Material for WS-C3560G-48PS-S switch.
Whether we should go for CAB-AC-JPN - AC power cord for Japan OR CAB-AC-ACE AC power cord for Europ
View 2 Replies
View Related
Nov 2, 2011
I recently removed a catalyst 2950 switch code version: c2950-i6q4l2-mz.121-13.EA1 ?I had an ASA 5505 connected as a switchport access to the 2950 on port 44. We will call the VLAN that the ASA sits on: VLAN 404. The 2950 had a trunk to our catalyst 6509 distribution switch carrying that VLAN 404. We also have a another VLAN for computers that sits on: VLAN 129, this is a standard DHCP vlan and it accounted for the rest of the switchports. The 2950 also has this trunked to our 6509 distribution switch.
Everything was working fine with that setup.After replacing the 2950 with a 3560 we started running into problems. The 3560 was configured the same exact way as the 2950. What was happening is that computers that sat on VLAN 129 started experiencing packet loss and were unable to work. It's as though the ASA was taking over the switch.
Is there a protocol that is enabled by defult on the 3560 that would do this?
View 4 Replies
View Related
Mar 4, 2012
I am having an issue with VoiP phones giving me an insufficient bandwidth message. I have three remote locations connected to our main building using 2 Mb point to point ethernet solutions through TWC. Each remote location has a Cisco WS-C3560-24PS running IOS C3560-IPBASE-M, version 12.2(25) and have the cable modems plugged into port 1 on them. The remote buildings are labeled 192.168.101.xxx, 192.168.102.xxx, and 192.168.103.xxx. There are 14-16 VoiP phones in each remote building. The main building being in the subnet of 192.168.100.xxx. I have the 3560s connecting to a single port on a 2801 in the main building, all using the subnet of 192.168.253.xxx The phone server sits in our network at 192.168.100.203. I have created the ACLs, class maps, and policy maps on all of the equipment.
For the remote buildings I have the following:
ACL
===========
Extended IP access list VOIP
permit tcp any host 192.168.100.203 dscp ef
permit tcp any host 192.168.100.203 eq 5566
[Code]....
I have put a hub in to capture traffic via Wireshark to see if DSCP flags are being appropriately marked and I do see that all VoiP packets are getting marked with as EF. However, I have been receiving phone calls from people in the remote buildings stating that their phones will cut out, flash Insufficient Bandwidth on the LCD displays and then the call will cut back in. I am wondering if the 2801 is not applying QoS with the rate-limits in mind since it is set to 100 Mb, or is it an issue with trying to take 3 remote locations and bring them down into 1 port on the 2801?
View 6 Replies
View Related
May 1, 2012
how to reset password on WS-C3560G-24TS?
View 1 Replies
View Related
Dec 10, 2011
I'm having trouble stacking a new WS-C3750X-24P with existing switches WS-C3750G-24PS ?I can see the license is on the new WS-C3750X-24P:
switch#sho lic
Index 1 Feature: ipservices
Period left: 8 weeks 4 days
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
License Priority: None
[code].....
I could put on the c3750e-ipbasek9-mz.122-55.SE1 image, but I may need to get the license sorted still, but not sure if that will work or how to add it if i got one.....
View 2 Replies
View Related
Jun 5, 2013
I receive a question from a future customer about this future if its supported on " WS-C2960S-24PS-L":configuring 2 dhcp server on this swith ( 1 dhcp for voice vlan , and 1 for Data Vlan).I did some search , but i didnt find the answer .i have to advice a customer before ordering the switch.
View 2 Replies
View Related
Feb 28, 2013
I've got two two 3560s switchs, (WS-C3560G-48TS-S) that I'm trying to connect to each other using the GB ports over Fibre. We purchased the following GBICs, SFP 1000SX Transceiver and when we put them in the port it shows (err-disabled). Below is some information I pulled from one of the ports, but doesn't matter what port I use they all say the same thing.
ProdSwitchSW1#show run int g0/51
Building configuration...
Current configuration : 37 bytes
!
interface GigabitEthernet0/51
end
[code]....
Configuration register is 0xF
View 3 Replies
View Related
