Cisco Switching/Routing :: How To Reset Password On WS-C3560G-24TS
May 1, 2012how to reset password on WS-C3560G-24TS?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: WS-C3560G-24TS-S / Inter Vlan Routing Stopping
Jun 16, 2011we need config on WS-C3560G-24TS-S inter vlan communication stopping as per attached document.
View 1 Replies View RelatedCisco WAN :: C3560G-24TS Switch Shuts Down?
Feb 23, 2011I have a Cisco C3560G-24TS Switch that has twice now just shut down and the only way to get it back to life is to pull the power and let it boot back up again.
Are there any logs I can check for poss clues as to why this is happening or any other things I can try?
Cisco Switching/Routing :: How To Reset Password For 887G
Feb 27, 2012I have tried pressing the Reset button (within 5 secs) when the router power up. On my HyperTerminal, the image was loaded and the line interfaces were up. But when I press enter on HyperTerminal, there was no response.
View 1 Replies View RelatedCisco Switching/Routing :: 871 Factory Reset Without Password?
Jan 24, 2012I recently decomissioned an 871 from a small business site and the owner did not want the device anymore. So now I'm trying to use it back at the office in the sandbox, however I don't know the password to the device and neither does the business owner. There's a reset button on the back, but from what I've read (here), it only loads a different config file found on the internal flash. Tried this, no dice. Is this essentially a bricked router now or is there anything else I can do to clear the config and repurpose it for my use?
View 7 Replies View RelatedCisco Switching/Routing :: Password Reset On PIX 506e
Apr 7, 2010I trying to do password reset on a 506e that I got with the current password unknown. I've gone to the Cisco URL for the reset: [code]
I am using the correct bin file as I checked with my pix version. Also I CANNOT ping the firewall from a PCor system on the network, but CAN ping everthing from the PIX.I've tried using interface 1 but no go. Also I've checked the TFTP software (Solarwinds) is running fine and I've unblocked it in XP's firewall.
Cisco Switching/Routing :: How To Reset Password Of ASA 5510
Nov 15, 2012I am trying to reset the password of ASA 5510,it is entering in Rommon mode but after boot command i am getting following error.
View 3 Replies View RelatedCisco Switching/Routing :: Password Reset 3548XL Switch
Feb 12, 2012I recently received a Cisco 3548 XL Switch, I'm trying to reset the password from the console. I've followed the steps but when I type from here: [code]
View 6 Replies View RelatedCisco Switching/Routing :: How To Reset Router 1841 Password
Sep 16, 2012Hava cisco router 1841 forgot user name and password and need to reset it to its factory setting
tried boot while holding ctrl and break get into rommon1>
rommon1>confreg 0*2142
rommon1>reset
still shows rommon 3>
Cisco Switching/Routing :: 3875 Router With NME-16ES-1G-P Password Reset?
Mar 9, 2011Acquired a 3875 Router with a NME-16ES-1G-P switching service module recently. I don't know what the passwords are. I reset the router, and gained access to it, but how do I reset the password on the service module?
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 2950 Failed Password Reset?
Jun 7, 2012I am not able to successfully accomplish the password reset function. This 2950 does not respond to the mode button held down at power up or to sending a briak. I have tried both several times and the switch continues to fully boot. [URL]
C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)Compiled Mon 22-Jul-02 17:18 by antoninoWS-C2950G-48-EI starting...Base ethernet MAC Address: 00:0b:fd:a1:4f:80Xmodem file system is available.Initializing
[Code].....
Cisco Switching/Routing :: Catalyst 3500XL Switch - How To Reset Without Password
Feb 23, 2012have a Switch I bought off a guy at work. Just to get into the Switching world of Cisco. He doesnt know the password on it and i cant reset the switch. I would like to mess around with it more but it doesnt load the flash or helper. It just sits there and holds. I have tried the password recovery and everything. Trust me, everything is correct, but it wont work for me. I cant load a new image to it because I dont have access to a server to get it from.
Base ethernet MAC Address: 00:0a:8a:94:58:c0Xmodem file system is available.
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init load_helper boot
switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4û
Cisco Switching/Routing :: Reset Password And Retrieve Configuration On Switch 2950 And 3560?
May 26, 2013how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 3560 - Access Switch To Reset Password To Factory Defaults
Nov 5, 2012Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
Last reset from power-on
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
[code]....
Cisco Switching/Routing :: Random Reboots On WS-C3560G-48TS
Mar 7, 2012This switch randomly reboots throughout the day. I checked the stacks info and reported it was using crashinfo_12 (report below). I have access to the switch throughout the day if more config info needs to exported.
Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE1, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code].....
Cisco Switching/Routing :: WS-C3560G-48PS-S Power Cord
Nov 23, 2011I need to prepare a Bill of Material for WS-C3560G-48PS-S switch.
Whether we should go for CAB-AC-JPN - AC power cord for Japan OR CAB-AC-ACE AC power cord for Europ
Cisco Switching/Routing :: ASA 5505 Connected To WS-C3560G-48PS
Nov 2, 2011I recently removed a catalyst 2950 switch code version: c2950-i6q4l2-mz.121-13.EA1 ?I had an ASA 5505 connected as a switchport access to the 2950 on port 44. We will call the VLAN that the ASA sits on: VLAN 404. The 2950 had a trunk to our catalyst 6509 distribution switch carrying that VLAN 404. We also have a another VLAN for computers that sits on: VLAN 129, this is a standard DHCP vlan and it accounted for the rest of the switchports. The 2950 also has this trunked to our 6509 distribution switch.
Everything was working fine with that setup.After replacing the 2950 with a 3560 we started running into problems. The 3560 was configured the same exact way as the 2950. What was happening is that computers that sat on VLAN 129 started experiencing packet loss and were unable to work. It's as though the ASA was taking over the switch.
Is there a protocol that is enabled by defult on the 3560 that would do this?
Cisco Switching/Routing :: WS-C3560G-48TS-S / GB Port Shows (err-disabled)
Feb 28, 2013I've got two two 3560s switchs, (WS-C3560G-48TS-S) that I'm trying to connect to each other using the GB ports over Fibre. We purchased the following GBICs, SFP 1000SX Transceiver and when we put them in the port it shows (err-disabled). Below is some information I pulled from one of the ports, but doesn't matter what port I use they all say the same thing.
ProdSwitchSW1#show run int g0/51
Building configuration...
Current configuration : 37 bytes
!
interface GigabitEthernet0/51
end
[code]....
Configuration register is 0xF
Cisco Switching/Routing :: Upgrading WS-C3750G-24TS-E1U To 15.0.1-SE2?
Feb 17, 2012I have the following switch:
#show version
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Image text-base: 0x01000000, data-base: 0x02C00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
[code]...
I have downloaded c3750-ipservicesk9-mz.150-1.SE2.bin and I want to upgrade iOS to this image.
I have a few questions related to this:
1. Is my switch model compatible with this iOS version?
2. Do you recommend the upgrade? Does it bring some notable features?
3. Can I upgrade for free or do I need to buy some license?
4. I also want to upgrade/add the crypto image, can I add crypto for free or some license is required?
5. I have remote access to my switch via the console cable which plugged into machine1. But machine1 is connected to network via the same switch. I am accessing machine1 via SSH, and then the switch via console cable (minicom on CentOS). Is there an upgrade procedure for this kind of situation that also has some fall back (like reboot in X minutes and load the previous image) if the upgrade goes wrong?
Cisco Switching/Routing :: WS-C3560G-24PS Configuring Ip Dhcp Snooping Database With Scp
Feb 10, 2011Just spoke to the TAC and didn't get the information needed. When configuring ip dhcp snooping database I am adding this to my configuration:ip dhcp snooping database scp://dhcpsec@192.168.1.50/home/dhcpsec/switch1.dhcp.database.txt..I assumed that to do this I would either specify the password on the command line, similar to the way its done when using ftp/http, or that I would need to create a public/private key.I have enabled scp and can manually copy a file from the switch to the linux server. So I believe I have all the aaa commands correct. Cisco WS-C3560G-24PS System image file is "flash:/c3560-ipservicesk9-mz.122-55.SE.bin".
View 3 Replies View RelatedCisco Switching/Routing ::WS-C3560G-48PS - IP Phone Gets Restart While Power Fluctuate
Jun 21, 2011We are using WS-C3560G-48PS connected via UPS power supply. Whenever raw power supply gets fluctuates few of the IP phones (Alcatel) gets reset although switch is remain up and running. We checked the same by disconnecting the raw power supply but we didn't found any packet loss from the node which are connected through this switch. But few IP phone gets reset. What could be the reason
View 2 Replies View RelatedCisco Switching/Routing :: Which Ios Will Support IPv6 Feature In WS-C3560G-48TS Switch
Feb 18, 2013I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedCisco Switching/Routing :: WS-C3560G-24PS - Checking Utilization And / Or Performance On Switch
Apr 23, 2012I have a WS-C3560G-24PS service as a distribution switch with six (6) WS-C2950T-24 connected to it. In looking at the utilization on the inter connect links no one is running close to a gig speed and this includes the link between this switch and the core. The CPU load (6%) and memory utilization (30%) on the switch do not seem bad so what else does one watch to see if it needs an upgrade?
We are starting tohave discussions about any needed upgrades on the network. I have an ocassional user that complaines about low performance but looking through the network I can find nothing glaring on a consistent basis that says an upgrade is warranted. I am however looking at things such as the above. Utilization on links, CPU, memory, etc.
Cisco Switching/Routing :: C3560G-48 - IOS Version Option Or Not Supported On Hardware Platform
Feb 6, 2012We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
View 3 Replies View RelatedCisco Switching/Routing :: 3750G-24TS Interface Drops?
Feb 6, 2012I'm troubleshooting interface drops. However the output of the following show commands don't match number of drops. Based on the output, can you find out what is causing the drops? the G1/0/28 is the uplink. Is that just the port got overrun by the traffic?
#show int g1/0/28
GigabitEthernet1/0/28 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0019.5667.191c (bia 0019.5667.191c)
[Code].....
Cisco Switching/Routing :: WS-C2960S-24TS-L / Mac Flapping On Stack?
Feb 27, 2012We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
On the devices log we get the following message:
%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?
Cisco Switching/Routing :: High CPU Utilization In 3560G-24TS
Jan 2, 2013getting CPU utilization around 62%
CPU utilization for five seconds: 54%/6%; one minute: 61%; five minutes: 61%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
35 82081 9642 8512 0.31% 0.21% 0.18% 0 Compute load avg
[Code]....
Cisco Switching/Routing :: Switch Not Usable WS-C2970G-24TS-E
May 9, 2013I have problem with my cisco switch 2970.
Initializing flashfs...
flashfs[1]: 5 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 5935616
[Code]...
Cisco Switching/Routing :: WS-C2960S-24TS-L / 4 SFP Ports For A Switch?
Jul 24, 2012I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
Cisco Switching/Routing :: WS-C3560G-24PS / Native Vlan Tagging And Vty Access To Autonomous APs?
Jan 14, 2013I've been experimenting with the 'vlan dot1q tag native' command on a switch and it seems as though tagging the native vlan breaks vty access to my access point.With the 'vlan dot1q tag native' commnand applied, I lose management connectivity to the AP with 'no vlan dot1q tag native' applied, connectivity is restored. Why is this? Is it safe to say that one can access the AP via vty lines using ONLY untagged packets?
SWITCH
Model: WS-C3560G-24PS
Code: c3560-advipservicesk9-mz.122-46.SE
--Abbreviated CONF
vlan dot1q tag native
[code]....
Cisco Switching/Routing :: WS-C3750G-24TS-S1U Slow Response Between VLAN’s
Jan 20, 2013Inter-VLAN applications are slow and same VLAN it is working fine.(i.e.VLAN to VLAN applications and File transfer response was Slow).Switch Model number: WS-C3750G-24TS-S1U
View 3 Replies View RelatedCisco Switching/Routing :: WS-C2960S-24TS / Default IP On Express Setup
Jan 3, 2012I just received three WS-C2960S-24TS-Land three WS-C3560E-48TD-S switches that i entered the Express Setup on as usual. On two of each type of switch i found the default network that is used to facilitate the Express Setup was 10.0.1.1 and the others used an IP range of 10.0.2.1, i realized this is a small negligible at best difference though i need to provide management with an answer as to why there is a difference between the two and can’t find anything online as to why there is a difference or something that proves there should be a difference. All the documentation I find sounding Express Setup notes that the IP range will be 10.0.1.1 not 10.0.2.1
View 3 Replies View RelatedCisco Switching/Routing :: Downgrade Firmware On C3750 V2 Switch 24TS-S V07 To 12.2(35) SE5
Apr 10, 2012Is there a way I can downgrade the firmware on a C3750 v2 switch 24TS-S v07 to 12.2(35) SE5. I have added this new switch to an existing stack but the FW is not compatable. I believe the answer is to upgrade the rest but I cannot afford any down time as they are used to run a CCTV securiy network 24/7. I have included details below to assist with my problem. Switch 4 is the one with a version miss match.
LNB-SWI3750-CTR-01#show verCisco IOS Software, C3750 Software (C3750-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 19:15 by nachenImage text-base: 0x00003000, data-base: 0x01080000
ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEE4, RELEASE SOFTWARE (fc1)
LNB-SWI3750-CTR-01 uptime is 19 weeks, 3 days, 22 hours, 46 minutesSystem returned to ROM by power-onSystem image file is "flash:c3750-ipbase-mz.122-35.SE5/c3750-ipbase-
[code]....