Cisco Infrastructure :: 1841 / 2960 Switch - Temperature OID Needed
Jan 24, 2012I need the temperature oid for cisco 1841 and 2960 switch.
View 1 Replies
ADVERTISEMENT
Cisco Infrastructure :: Temperature Status From 2960 Switch Using SNMP Not Working
Sep 18, 2012WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Cisco Switching/Routing :: 1841 Not Synchronizing With 2960 Switch
Oct 22, 2012I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies View RelatedCisco :: 2960 - Unable To Find OID Of Temperature Monitor
Dec 21, 2011I have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies View RelatedCisco WAN :: Why Getting Temperature Event In 3560 Switch
Mar 9, 2013why getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies View RelatedCisco :: Catalyst 3560G Series Switch - Wrong Temperature Reading
Feb 26, 2012I am trying to get the temperature reading from one of our 3560G Switches using SNMP. When I run an snmpget on the Switch it returns back to me a "1".
So when I run the following I get:
> snmpget -v1 -c public 192.168.x.xxx 1.3.6.1.4.1.9.9.13.1.3.1.3.1005
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1005 = Gauge32: 1
But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
Cisco Switching/Routing :: Modules Operating Temperature And Major Error On 6509E Switch
Apr 6, 2013we have two 6509E which are configured in VSS mode with the following modules in each:
1 48 CEF720 48 port 10/100/1000mb Ethernet
2 8 DCEF2T 8 port 10GE
3 4 CEF720 4 port 10-Gigabit Ethernet
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
I need to know if the temperature of the attached modules are normal or there is a problem?
the status of one of the supervisor engines is "MajFail" as shown below:
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
5 Major Error
Cisco Infrastructure :: 2960 Clock Time Not Set
Mar 6, 2012I am using Cisco 2960 access switches and dont have NTP server so i can manually set time on switches but problem raised when these switches restart they show their factory default time.
View 2 Replies View RelatedCisco Infrastructure :: WS-2960 Gi Duplex Will Not Set To Full
Jul 28, 2011I have the following configurations for switch to switch connectivety. sh int sh config int
2960 will not take full duplex setting.
Core switch
WS-C4506 cat4000-i9s-mz.122-25.EWA10.bin
FastEthernet5/8 is up, line protocol is up (connected)
[Cdoe]....
Cisco Infrastructure :: Can 1841 Router Boot From System Image From USB Disk
Jan 12, 2013I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies View RelatedCisco Infrastructure :: Can't Upload By Tftp On Any Catalyst 2960
Dec 17, 2012i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View RelatedCisco :: 2960 Prime Infrastructure Client Tracking
Jan 14, 2013I'm running PI 1.2.1.012 and I'm having issues populating client information. Most of my switches are 2960 series. Specifically I get a lot of MAC Address "Unknown" and nothing in the IP address field. I probably get about 25% of the correct MAC address and 10% of the IP addresses. I also run CiscoWorks Prime LMS 4.3.2. and the user tracking information is about 98% correct pertaining to MAC address and IP address. My other network management tools also are very accurate.
View 1 Replies View RelatedCisco Infrastructure :: 2960 - High I / O Memory Utilization
Oct 26, 2011We recently installed two 2960, both of them with this fw version:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
The switches see very few traffic (under 40MB on all interfaces, summed, so far), however, I/O memory utilization is about 80% as can be seen from the show memory command:
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor 2B89A18 73969000 27198964 46770036 45060368 29367536
I/O 6200000 14680064 12185292 2494772 2323116 2380896
Driver te 1A00000 1048576 44 1048532 1048532 1048532
The memory allocated is almost all Packet Data, by init, "sho memory io dead" returns zero, the memory usage seems constant, there are no errors on the log, the switches operate correctly, no packet has ever been dropped, CPU usage is about 4%.
Here I showed info for one switch, the other is in the same situation. I just want to know if this behavior is expected, I don't want to find out problems when the switches will be in production whit real traffic.
Cisco :: 2960 - Prime Infrastructure 1.3 - Adding Devices
Apr 9, 2013I just got PI1.3, I'm new with it, and I don't know how to add devices. I have an 4500-X, an 3850 and 12 pcs. 2960S.
I see that are some out-of-the-box templates, but when i try to deploy, for example "medianet perfom" in Devices box I got "no data available"
What I have to configure on switches?
Cisco Infrastructure :: 1841 Dialer Profile - Connection Exists But No Telnet Session Possible
Jul 11, 2012I have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]
Cisco Infrastructure :: 2811 / 1841 / WIC-1AM-V2 - Setup POTS Dial Connection Between 2 Routers?
Jun 17, 2012I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
Cisco Infrastructure :: 1941 / 5505 / 2960 - Traffic Prioritization
Sep 12, 2011How I can prioritize Web Ex, Skype and some two websites on Cisco equipment. My set up is such that my 512kbps link goes to a Cisco 1941 router>Cisco ASA 5505>Cisco Catalyst Switch 2960>Computer.I want to be able to prioritize this on my network and test that it actually works.
View 1 Replies View RelatedCisco Infrastructure :: Is GLX Compatible With 3750G-24PS Switch
May 23, 2011I am trying to buy a GLC-SX-MM SFP module via Fed Stock, and I keep getting a GLX-SX-MM. What is the difference between these two part numbers? I can't find it on the Cisco Web site and eve a search of Google comes up relatively fruitless! Is the GLX compatible with my 3750G-24PS switch?
View 2 Replies View RelatedCisco Infrastructure :: Finding Replacement For Switch C4006?
Oct 3, 2012Right Now we are using Cisco switch model c4006.and we are looking to replacement for the same . Below are our requirements.
1: Around 120 Ports (100 Mbps)
2: Around 30 Ports (1Giga)
3: Layer2/Layer3
Cisco Infrastructure :: 3524xl-EN Switch Not Displaying Any Output
Oct 6, 2012I have 2 cat3524xl's and a 3550. I recently did something to the IOS that makes the switch not display any output to the console port. Not sure what I did but even doing the reset as instructed in the Cisco docs by holding the mode button foe 2 seconds after boot. I get the flashing green light but still no output. All POST tests pass according to lights so I tried different cables and all baud rates with no change. I hoocked switches back up in lab and can see them in CDP neibors but do not know how to access them from there as they have no IP assigned to them. Remember this is two of them with exact same issue.
View 2 Replies View RelatedCisco Switching/Routing :: Add SMB SF300 - 24 Switch To Infrastructure
Nov 18, 2012I am trying to add a Cisco SMB SF300 - 24 Switch to an infrastructure which has only Cisco Catalyst Switches The Core layer is Cisco Cataylst 4503 . Distribution is Cisco Catalyst 3560 and the Access Layer is Cisco 2960 Switches.There about 30 VLANs present in the infrastructure which is advertised to all switches using VTP. Inter VLAN routing is done at the Core Switches by creating Interface VLANs for every L2 VLAN.
1. The new VLAN 150 needs to be created on the new Cisco SMB Switch. If I create a corresponding interface VLAN 150 on the Core Switches , will it route traffic to other VLANs just like it is currently working for Cisco Catayst 2960 Switches ?
2. Upon checking I could see that VTP is not supported on Cisco SMB Switches and I would need to go for GVRP if I need to advertise VLAN information to other Switches. But since GVRP is supported only on CatOS and there is no inter operability between GVRP and VTP , I would need to create VLANs manually on the new Switch . Is that correct ?
Cisco Infrastructure :: Converting WS-C3560G Switch To DC Power?
Apr 15, 2013What needs to be done to convert a WS-C3560G-24TS-E to DC power?
View 2 Replies View RelatedCisco :: Manage Switch SMB 300 Series Using Prime Infrastructure 1.2?
Mar 3, 2013Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
View 1 Replies View RelatedCisco Infrastructure :: Use HWIC-4ESW As No Switch Port?
Oct 4, 2012Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies View RelatedCisco Switches :: 3750 / SMB Switch Integrations With Non-SMB Infrastructure?
Jul 27, 2011A customer is expanding their network into another wing, and they have a good number of existing Small Business switches (specifically the SGE-2010P - [URL] that they're interested in possibly deploying. They have a full-blown Cisco infrastructure and voice deployment (Cat 6500 core switches, 3750 switch stacks, Communications Manager w/ over 1,000 phones, etc.).
The general concern is whether there is ANY known issues or concerns with trying to mix/integrate the Small Business equipment with non-SMB infrastructure. Looking at the datasheet for this switch, it's clearly PoE, supports QoS, although it doesn't specifically indicate it can provide a voice/auxiliary VLAN for a phone detected by CDP - that would be a big deal. So basically, "a switch is a switch", and I'm just posing this question to make sure there's no reason (technically or from a support standpoint) that we would not recommend integrating these.
Cisco Infrastructure :: 2811 Router Is Sitting Behind 3650 Switch?
Jul 9, 2012Seeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies View RelatedCisco Infrastructure :: 3550 - Limiting Power Allocation To 15.4 W On Pre-POE Switch?
Jan 2, 2013I'm using a Catlyst 3550 to supply power to a IP network surveliance camera. By default, the predecesor to POE, Cisco Inline Power allocates 15.4 W of power to a port ... What is the process for reducing this power output?
"For an IEEE device, the switch always allocates 15.4 W to the port. The switch does not display the IEEE class type in the show power inline privileged EXEC command output. Instead, it displays n/a."
Cisco Infrastructure :: No Icmp Reply From Catalyst 2950 Switch
Nov 15, 2005My switches is still operating but when i ping the switch, there isn't any reply. No icmp reply from catalyst 2950 switch
View 6 Replies View RelatedCisco :: 2960 / Login To Switch Via Ssh?
Aug 25, 2011i have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
Cisco WAN :: How To Enable SSH CLI On 2960 Switch
Nov 12, 2012i would like to know how to set the following on cisco ws-c2960-24 ttl:
1. SSH CLI
2.PORT SECURITY REMOVAL: Limits MAC@per port with no shutdown
3.Set port to protect
4.Set RSTP
5. Finally how do i set up TFTP Server from windows server 2008
Cisco WAN :: Ios Upgrade On 2960 Switch
Dec 15, 2011I have a cisco catalyst 2060 poe switch, exitsting flas is flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin
I downloaded latest flash (c2960-lanbasek9-mz.150-1.SE.bin) and updated the new flas through telnet while reunning tftp server. and tftp server is given the message sent 2960-lanbsek9-mz,SE.bin to (10.10.10.1), 11847957 bytes
after reload the system i login telnet and saw the verson still it is showing old verson, then how can i comform flash is up-dated or not...
DETAILS
my tftp server ip is: 10.10.10.10
switch ip is: 10.10.10.1
Cisco WAN :: Switch 2960 To Enable SSH V2
Nov 23, 2011i have a switch 2960 24TC-L with c2960-lanbasek9-mz.150-1.SE.bin and SSH v1 enabled.When i try to enable SSH v2 the swith tell me that i have to create a crypto key rsa. I generated the crypto key rsa with 1024 bits and when i try to enable the SSH v2 i receive the same message.
View 10 Replies View RelatedCisco WAN :: How To Shutdown 2960 Switch
May 16, 2012how to shutdown the cisco switch 2960.......
View 5 Replies View Related