We are a small business that just bought a Cisco 1921 ISR. I am trying to set it up right now but I cannot get CCP to discover it. I am new to Cisco products and IOS.The router is currently set up in a test environment with a USB connection to a Win7 PC for console management. I also have the PC connected to gigabit ethernet port 0/1. I am using putty to access the console which I did with no problem for the initial configuration. After that I thought I would be okay to discover the router with CCP using the IP address I specified but then it prompted me for a username/password which I didn't see in the initial configuration. After this I did some research and found out I needed to set up a few more things so I ran the following commands: [code]
After this the video I was watching said to go in to CCP and specify the IP address or hostname of the router and use the login info that was just created admin/pw. When I ran the discovery I got the failure message: Connection to the device could not be established. Either the device is not eachable or the HTTP service is not enabled.When I run 'show ip interface' I notice 'Router Discovery disabled" is this why it is not working? How can I enable this or what else am I missing here? Am I not connecting to the router correctly? Oh and just for reference our plan is to have this router set up as a VPN gateway and firewall with 2 WANs for redundancy and connecting to our switch via an HWIC SFP for fiber.
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability delay down 1 up 1 ! track 20 rtr 2 reachability delay down 1 up 1 ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
I have installed LMS 3.2.1 and RPM(ATM technology) can be seen but not ML card(ONS). Also LMS discovered lot of interfaces (int vlan) one of the core switches and marked them as 'unreachable'. How can delete these when LMS marked as unreachable?
i have 2504 controller with 7.0.116.0 software and some 3502 APs. I also using 5 APs now and few days ago I bought some additional 3502 APs and I can't get them connected to the controller. My company admins decided to using DNS controller discovery instead of using DHCP option 43. I'm connecting APs to access ports of Linksys switches and APs not in the same subnet as ap-manager interface of controller. AP succesfully get IP and DNS from DHCP and could ping cisco-capwap-controller. However, I have such messages.
*Mar 1 00:12:32.014: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state. *Mar 1 00:12:40.533: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
I can succesfully ping controller from AP AP30f7.0d2e.9a58#ping cisco-capwap-controller Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.23.16.30, timeout is 2 seconds:
I have a 5508 controller that has 14 APs connected to it. I installed them without an issue. The 2 new APs are on a different subnet. I can ping them from the 5508 controller ping command, but they do not self discover from the web interface. The 2 new APs are at a differnet physical location.
i am using cisco LMS 2.6. Is it possible to discover devices through SNMP RW string?as LMS is not doing so. is is deffendable for me to have two strings RO and RW for discovery of the devices ?
I have Windows 7 64 Bit Pro PC connected directly to the router via Ethernet.This is I will call Ethernet Connection 1.I also have a Windows XP Pro SP3 computer connected to the same router but via a wireless connection.I have both PC's connected together via an Ethernet cable. This I will call Ethernet Connection 2.It all works fine, but I only want my PC's to communicate via Ethernet connection 2.Currently, if I disconnect the Ethernet cable between the computers I can still access the files on the Windows 7 computer via the wireless connection on the Windows XP computer.I've tried to see if this is discoverable by other people using the router by installing Ubuntu on the Windows XP machine and looking at the available networks. Lo and behold, my Windows 7 machine is discoverable and accessible - albeit by a password. This is with the Ethernet cable between the computers unplugged.I have both networks on the Windows 7 machine set to public and all sharing options switched to off. Both computers have the same workgroup name. Worryingly I can still connect to the Windows 7 machine via Ubuntu wirelessly without even using the same workgroup name!All I want to do is connect the two computers via Ethernet Connection 2. I don't want any sharing information going to the router too and hence other poeple being able to see it. Ethernet Connection 1 on the Windows 7 machine is for the internet only (same as for the wireless connection on the XP machine).
Using a command prompt, how do I discover the internal IP of an unused router, which I set to a custom value and forgot? The router is not currently in use for internet access. I would like to access the control panel of the router without resetting it.I attached my netbook to the router with an RJ45 cable and disabled the netbook's wireless adapter to avoid conflicts with my current network. Using an elevated command prompt, I did an "ipconfig /release", rebooted and ran "ipconfig /all", but the gateway entry is blank. An "arp -a" returns 169.254.190.120 as the only interface. A "netstat -a" returns 169.254.190.120:xx...'s, 127.0.0.1:xx...'s, and 0.0.0.0:xx...'s, but no router internal IP address.Is there a way discover the attached device without resetting?
I have a 3750 that when a client computer shuts down the switch will not discover it on start-up unless I bounce the switch. Pretty dependable product so,.... did I miss something in my config? Switch is GBIC'd for Fiber?
I am unable to discover 2 Nexus 5548 with the SAN client of DCNM 5.2(2e)
These Nexus are used like LAN and SAN switch. Each Nexus is a SAN fabric. I would want to use DCNM in order to configurate the zone/zoneset via GUI. These Nexus 5548 run 5.1(3)N2(1b) release.
The Nexus ARE NOT managed via the Mgmt interface (OOB) but they are managed via an interface vlan (InB)
I could not configure rightly
- the snmp-server user (SNMP user V1/v2 or V3 + group ? ) CLI on Nx
- to configure the discovery in order that DCNM discover each fabric either from web GU interface or java SAN client
I am trying to get our DCNM to discover the 5548. When I put my credentials for that appliance. I get this error .Failed Device x.x.x.x OS Version 5.1(3)N1(1) is not supported . The DCNM version we have is 5.2(1)S74.
I'm new on this site and having SLM2008 switches. I've been trying to solve the problem for quite a while, but so far I was unable to solve it. So here it is:
I'm trying to send IP TV from ADSL box (aka Free box) located in a small annexe of the house where the telephone line enters. Whole house is wired with 1Gb CAT6 cable. I'm using this wiring to get internet connectivity in different parts of the house and this works great. Now the idea was to create a separate VLAN on my 3 SLM2008 switches to get IP TV stream from ADSL box to the media box (also provided by ISP, aka Freebox HD). Different V LAN configs did not work for me: Free box HD would stuck on boot claiming it doesn't "see" the network. So then I've decided to go from simple things to more complex and removed the V LAN (came back to default config) and connected ADSL box with Free box HD with just one SLM2008 in between. Surprisingly it did not work! Same error on Free box HD! So I plugged the hub and started my Wire Shark to see what is going on.
First tried without the switch (just with a hub in the middle) and I saw successful connection: 1) Freebox HD send DHCP Discover 2) ADSL box responds with DHCP Offer 3) HD sends DHCP Request 4) ADSL issues a DHCP lease
Free box HD is ready to show any channel from ISP.
Secondly I plugged SLM2008 back and looked at traffic right after ADSL box: No DHCP packets seen at all! Then I moved hub next to Free Box HD and I saw it keep sending DHCP Discover every 30 seconds or so.... And it was not getting reply back.
So my conclusion is that SLM2008 for yet unknown reason would not let DHCP discover pass.... I've tried un managed Net Gear switch and *boom* Free box HD booted without a problem. I looked through SLM2008 settings and I have not found something relevant.
How to make my switch pass DHCP discover? If yes my next question would be how to configure V LAN on 3 switches to make it deliver IP TV to my TV set.
I have a Belkin G wireless router. I have connected a Windows 7 PC using wired connection through Ethernet port.I've also connected my Windows XP PC through wireless connection. And plugged in my internet cable to the Router.Now I am able to access internet on both the PCs but I couldn't setup a network between the two computers for file sharing.
how can i discover product actual part number from the device through console.I have a bought a cisco ASA5540-AIP20-K9 and i want to check either is the product is shipped us as a right product.And i want to check total BoM requriements from entering the ASA console through any CLI Command.Below My Cisco ASA BoM which i purchased.
ASA5540-AIP20-K9ASA 5540 Appliance w/ AIP-SSM-20, SW, HA, 4GE+1FE, 3DES/AES1CAB-ACUAC Power Cord (UK), C13, BS 1363, 2.5m1SF-ASA-8.3-K8ASA 5500 Series Software v8.31SF-ASA-AIP-7.0-K9ASA 5500 Series AIP Sofware 7.0 for Security Service Modules1ASA-VPN-CLNT-K9Cisco VPN Client Software (Windows, Solaris, Linux, Mac)1Included: ASA5540-VPN-PRASA 5540 VPN Premium 5000 IPsec User License (7.0 Only)1Included: ASA5500-ENCR-K9ASA 5500 Strong Encryption License (3DES/AES)1Included: ASA-AIP-20-INC-K9ASA 5500 AIP Security Services Module-20 included w/ bundles1Included: ASA-180W-PWR-ACASA 180W AC Power Supply1Included: ASA-ANYCONN-CSD-K9ASA 5500 AnyConnect Client + Cisco Security Desktop Software1CON-SU1-AS4A20K9IPS SVC, AR NBD ASA5540 w AIP-SSM-20,4GE + 1FE,3DES/AES1
We have a number of 6509s which generally have dhcp relay agents configured on the SVIs. The dhcp servers are centralised. Recently we've had one or two faults with misconfigured or faulty devices (blade server chassis and also printers) generating high volumes of dhcp discover packets and causing high cpu on the relevant 6500. I would like to rate limit these discover packets, which are layer 2 broadcasts. Storm control can't discriminate between different types of broadcasts and on a gig link would need to be set down at about 1% to have much effect on the problem. I've looked at CoPP and also mls hardware rate-limiting but as I understand it, these two features don't control broadcast traffic. I also looked at dhcp snooping but if an interface receives a high level of dhcp discover broadcasts, e.g. over 100pps, I don't want it to go error-disabled (as this would knock down the whole edge switch), just to drop the excess packets.
Anyway, I am looking for a way to discover host names of Apple devices (namely iPods and iPhones) that are on our network. I've tried a number of programs like Nmap, Advanced IP Scanner, and LanSpy to name a few. All of them will report back the MAC address with no problem but no dice on resolving the host name.
My goal is to use the host name to identify the device, and ultimately the person with the device. Any thoughts on how I can go about this? Is there a setting in Nmap I'm missing or perhaps a better program to use?
I have changed from a DSL internet service to a Comcast cable system. I have setup my E4200v1 router as an Access Point, to extend coverage in my building. It works fine, but I can no longer log on to the unit using its' IP address 192.168.1.1. The browser returns the message "Internet Explorer cannot display the webpage." If I want to tweak the settings the only thing I can think to do is to push the reset plug, back to factory settings and go through the whole process. Is there a way to discover the new IP address of the reconfigured router? I left the default address as it was when I made the changes to AP status.
I've just upgraded my home wireless from an NetComm NB5540 + modem to a LinkSys X3000.Internet access works fine for all devices, but some wireless devices can't "see" my Win7 desktop system that's on a wired connections to the router. Galaxy Note phone (running ICS 4.0.4) can discover and connect to file shares on my desktop system without any problems.Asus Transformer Prime tablet (running JellyBean 4.1.1) can see the router on the local network, but can't see my desktop. Even if I manually type in the IP address it can't connect to itLikewise my old WinXP laptop can see the router but can't see or connect to any other devices.
I tried connecting the NetComm router with just Wifi configured to one of the ethernet ports on the X3000, so I've got two Wifi networks running in parallel. If I connect to this second WiFi network with any of the above devices then they can all discover and connect to my desktop system on the wired connection to the X3000.
I'm able to use the web interface to the router, from one computer (Windows XP, IE 8). But from my other computer (also Windows XP, IE 8) I can log in to the router, but then the browser just presents an empty screen. I haven't been able to discover any setting in the browser that could cause this. From this same computer, I can access the web interface with no problem, using Google Chrome browser! So the problem seems to be in IE.
I have installed a Cisco 1921 router in our company and i have stumbled upon an issue with the DNS.
We have a internal DNS server and an internal WEB server. In the DNS server there are records pointing to sites on the WEB server, this is working just fine.
The thing is when i use a public DNS such as 8.8.8.8 (googles public DNS) i cannot resolv the external IP of those sites. I do not want to access the sites and i do not want to send any packets to the sites. All i want is to query the public DNS and resolv the public IP where the site is.
I have been playing around with a 1921/K9 router in our dev environment. It's been about 24 hours and I just can't seem to get it to work. My DHCP Server is working hence my internal network is getting IP address as desired. But Router doesn't seem to connect to internet for some reason.
I am trying to make it a internet facing router with static IP address (67.210.209.113). LAN side of this router will be our .11 Network which is our Dev Network.
Here is some network information:
WAN: Interface IP: 67.210.111.111 Default Gateway: 67.210.111.222 (I can ping this address through router) tlm1921A-11A#ping 67.210.111.222
Any issues upgrading the IOS on a 921 router.How can i create a certificate for the new IOS? I've never had to do this for other IOS 15 upgrade?I've confirmed the IOS is not corrupt and if i upgrade the router in ROMMON the router boots correctly.
I have purchased a PAK for my 2 cisco 1921 routers .I would like to to configure IP SEC or SSL for VPN connectivity on the routers. How do i convert the PAK into a license?
I am really stuck with router requirement for one of our client. I need 891 SEC router. I think this comes with advanced IP services. What I have is 1921, with IP Base. can I upgrade 1921, so it will become alternative to 891 SEC.
I'm attempting to set up a Cisco 1921 router running IOS15, and am having trouble with the NAT - it might be that what I am attempting is not possible. The only traffic going across the router is UDP, and the outside of the network canot be changed.
I am trying to get the Cisco 1921 to route between 2 LANs. I can ping from the router itself, but cannot ping across either, is there something I am doing wrong here:
version 15.1 ! no aaa new-model ! no ipv6 cef ip source-route ip cef
I am fairly new to Cisco, but am trying to configure a 1921 router to give higher priority to SIP/VoIP traffic (Port 5060) than everything else.The connection is only 4Mb and is getting hit hard by video streaming, I don't want to block this, just make a lower priority.Any ideas where I am going wrong?My current config is as below.The IP addresses have been changed for security reasons, but in reality are both in the same range, i.e. are both external IPs, so I am not sure if this is causing the problem. Do I need NAT for QoS to work?
