Network Scan To Discover Rouge Apple Device Host Names
Sep 27, 2011
Anyway, I am looking for a way to discover host names of Apple devices (namely iPods and iPhones) that are on our network. I've tried a number of programs like Nmap, Advanced IP Scanner, and LanSpy to name a few. All of them will report back the MAC address with no problem but no dice on resolving the host name.
My goal is to use the host name to identify the device, and ultimately the person with the device. Any thoughts on how I can go about this? Is there a setting in Nmap I'm missing or perhaps a better program to use?
View 2 Replies
ADVERTISEMENT
May 12, 2012
I am able to connect to corporate VPN with no issues when connecting directly to ISP modem. When I try to complete the same VPN connection via a Wireless Router (Linksys WRT160Nv3) i get the following message: "Network error. Unable to look up host names"I have tried connecting and it will initially connect, but 15-30 seconds it will drop and connection can't be re-established.Is there a setting on the Linksys WRT160Nv3 that needs to be changed?
View 3 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Sep 17, 2011
Is it possible to give me NAS and Xbox 360 Host names so that they show up in my DHCP Client list? Currently there are 13 devices connected, 11 of which have a host name but these two do not. It also shows the IP and MAC addresses of each connected device.I just want to make sure that all of the devices that are connected are what I would expect.
View 1 Replies
View Related
Sep 30, 2011
I have been asked to do is locate some computers on the network and run a security scan on them. Well i pinged the host name and got an IP address. Then the network admin me look up the switch port that the computer is located on and so on. So i find 3 of the computers im looking for and when i get on the computer and look up the name but it does not match the name given to me. So i do an ipconfig /all and see that the computer has the right IP address and MAC address but not the same name. So my main question is, are these computers one in the same or is something messed up?
View 1 Replies
View Related
Nov 30, 2011
where the host names do not properly resolve with the right ip address.Example, I ping a host name, it gives me an IP, but when I VNC into the workstation, it is a totally different host.
View 2 Replies
View Related
Dec 25, 2012
I have issues with the same host name duplication in different VLAN's in the same domain.Scenario:I have 2 VLAN's named VLAN A and VLAN B.If i assign in VLAN A for one of the computer name as Comp1 it's not in the network so its accepting.in dns will be replaced with VLAN B and if i ping i can see the ip also from VLAN B.
View 18 Replies
View Related
Apr 21, 2011
I was thrown into trying to fix a friends pc being told that the internet wasn't working.What I've found through some messing around is that I am able to pull up websites with the ip address but trying to use the domain name give a "Host Not Found". Similar error when trying to do a ping. However doing an nslookup will pull the ip's for a domain. I've done the dns flush, the netsh commands that are floating around to no avail.
View 7 Replies
View Related
Aug 9, 2011
I an doing device discovery and get the result as devices are unreachable and only 1 device among them getting discovered.Any inputs?
View 1 Replies
View Related
Apr 6, 2011
I want to mark company owned laptops with a registry setting and have our ASA 5520 identify these systems when connecting via SSL and IPSEC remotely, and allow broader access to the internal network than the telecommuter that use their personal PCs. For the users that connect with their personal PCs, I want to only allow RDP access to their company PCs on the internal network.
Can I accomplish this with the current VPN Plus license and Anyconnect Essentials feature enabled? If not, what license/features do I need installed/ enabled to accomplish these objectives?
View 1 Replies
View Related
May 20, 2012
I'm having with my VPN Server on my Cisco 2621xm.
I started by creating a VPN - everything worked great. I assigned the DNS Servers, Domain name, WINS Server so when I connect I'm able to resolve local hostnames on the network with no problem, however, I had no internet access... I then set up a split tunnel access list. Since I've set that up, I'm now able to ping internet based addresses url... but no longer able to resolve internal host names. I can ping the ip addresses, just name resolution no longer works. [code]
View 4 Replies
View Related
Mar 3, 2013
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
View 5 Replies
View Related
Jan 4, 2012
I tried to discovery WS-C4507R+E devices with lms 4.0 but the devices result unknown, any package to install to discover these types of device?
View 1 Replies
View Related
Jul 6, 2011
I have a very basic WLAN setup with a 2106 controller and 3 (will be 4) 1140 APs.As part of securing the network I have been testing the rouge detection. The system has no trouble detecting and shutting down honeypots. I would like to also automatically shut down Rouge on Wire points. The system sees my test AP just fine. And I have it completely open (no security). But the system never detects that the rouge is on our network so no action is taken. I can connect just fine to the test AP with no encription using DHCP and communicate with everything on the network just fine.Is there some setting I am missing that allows the APs to detect that an AP is on wire?
View 2 Replies
View Related
Dec 6, 2011
In asus router model rt-n10, there is a client list when you bring up 192.168.1.1 showing names of devices also mac addresses and ip addresses. How do I add names to the list so I know which devices are using what ip etc. I have tried the advanced settings in the router to see if I can do it this way , but no luck.
View 1 Replies
View Related
Feb 8, 2011
I had a Linksys BEFSR41 router with AppleTV 1stGen with 0 problems.Now I have a DIR-655 Vb1 2.00NA firmware and itunes now cannot find the AppleTV as a device. I have tried resetting the AppleTV to factory defaults re-installing latest firmware and reinstalling itunes, powering down all devices etc., and no way can itunes find the appleTV although the appleTV is on the net and seen by the router.I have gone to a wired connection to the router too because the router kept dropping the wireless connection to the router too. Of course I got the DIR-655 for wireless
View 15 Replies
View Related
Jan 12, 2012
how can i check if my netgear N300 adapter wna3100 is compatible with apple tv device I was told that I needed a dual band router to play HD movies from itunes (ipad)
View 2 Replies
View Related
Jan 2, 2013
I am using a EA4500 and use Linksys Smart Wi-Fi to manage the device. In the household we have multiple Apple i devices. Somehow the Linksys Smart Wi-Fi combined two separte i devices (iPhone 5 and a 4th generation iTouch) to one user.The devices actually have different names, but the Smart Wi-Fi is combining them into one device. So I can't use Parental Controls on one of the devices.
View 8 Replies
View Related
May 22, 2011
my hp mini is showing no network connections connect to the internet?
View 1 Replies
View Related
Apr 30, 2012
I have a Belkin G wireless router. I have connected a Windows 7 PC using wired connection through Ethernet port.I've also connected my Windows XP PC through wireless connection. And plugged in my internet cable to the Router.Now I am able to access internet on both the PCs but I couldn't setup a network between the two computers for file sharing.
[code]...
View 2 Replies
View Related
Oct 22, 2012
A customer of ours has the following access points and wireless lan controllers on site. They want to use the Apple Bonjour service with Apple TV's and iPads. I have enabled multicast feature of the 5508 globally and one the SSID.The Apple TV has an ethernet connection and the iPads connect over the wifi. The Apple tv is on the same subnet as the iPad's - the Bonjour features do work for approx 5/10 minutes then it stops working for some reason. The Access Points plug into a Cisco 2960 Layer 2 switch, the 5508 controllers plug are in LAG mode and plug into a Nortel Layer 3 stack which I have enabled IGMP snooping.I've read that the Apple Bonjour service isnt designed to work on a multi subnet network - but both the Apple TV and iPad are connected on the same subnet. Sounds like some kind of timeout but not too sure.
View 5 Replies
View Related
May 15, 2013
how to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
View 1 Replies
View Related
Jul 19, 2007
I have an ASA5505 running ver 8.0(2). I have configured the ssh timeout, ssh host commands and did the crypt o key gen. I am unable to access the device from the host I am allowing. Is there like ca save all command required? I am trying to use the default pix and telnet password. Do those still work?
View 3 Replies
View Related
Nov 15, 2012
I have an old network with 5 computers, now one of them is damaged and i copied the file into another computer.2 computers are set to save files in a database which were in the damaged computer.how can I give to one computer two names ? - i cant change the source program to read the database from other computer..The program searches for \computer_namedatabasedatabase file.mdb (I dont want to change the the computer name because other computers search for him under the other name.
View 4 Replies
View Related
Jun 24, 2011
the setup is as follow: I have two separate network.192.168.90.xx and 10.10.xx.xx the two boxes being connected via an ethernet cable. How would I go about having a 192.(...) machine speak to a 10.(...) box? My boss tells me that via a UDP call the 192.(...) machine can get the IP of a 10.(...) box. Isn't UDP dependant on a subnet mask to limit the # of queries, and in that case would it even be feasable? I was thinking instead of spoofing the 192.(...) IP to an unoccupied 10.(...) IP. Of course to do this would require knowing what IPs are unoccupied on the other network, and I cannot assume the would respond to pings.
View 5 Replies
View Related
Aug 27, 2012
The rouge access points being detected by the 5508 WLC are not showing up on the Context Aware tab of NCS? I have a MSE 3310 installed and configured and it shows to be syncronizing with the WLC. I'm sure I am missing some part of the configuration just not sure where.
View 3 Replies
View Related
Aug 10, 2011
I am trying to use Nmap to determine whether a certain IP address is available or not. However, the output of the scan shows that it scanned the subnet my computer is on and only one address in the network I typed in (MPLS network). Is there any way I can have Nmap only scan that one subnet and not all the others?
View 5 Replies
View Related
Oct 20, 2011
cant scan through network with xerox docucentre iv 2260
View 3 Replies
View Related
Sep 12, 2011
I'm running Windows 7 Pro. I noticed tonight when I clicked on Network in Windows Explorer that in addition to my home PCs there is a PC with someone's name on it. My suspicion is that my wireless ISP has screwed up in some way. I ran SoftPerfect's Network Scanner and don't see any strange IP addresses, so this stranger's PC is not on my subnet. What tools are available to scan my network and give me more info about the stranger's PC?
View 6 Replies
View Related
Jan 7, 2013
I have a dell 2155CDN network printer I want to scan files over the network when I scan once it finishes I get a SMB List error and the file does not go trough here is a picture of my settings?
View 4 Replies
View Related
Jan 3, 2012
I can print from hp printer photosmart c6280 but cannot scan its on network
View 1 Replies
View Related
Jan 7, 2013
just bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies
View Related
Mar 29, 2012
I have a Linksys E2500 router. Is it possible to have one network name for the secured network and a different network name for the Guest network? The thought is to not have the SSID of the secured network broadcast while allowing the SSID of the Guest network to be broadcast. With the convention of simply adding "Guest" to the end of the SSID for the secured network, it defeats the security option of not having the SSID of the secured network broadcast.
View 1 Replies
View Related
