Cisco :: LMS 3.2.1 Not Discover ML Cards (ONS)

Mar 12, 2012

I have installed LMS 3.2.1 and RPM(ATM technology) can be seen but not ML card(ONS). Also LMS discovered lot of interfaces (int vlan) one of the core switches and marked them as 'unreachable'. How can delete these when LMS marked as unreachable?

View 1 Replies


ADVERTISEMENT

Cisco :: LMS 4.0 Not Able To Discover Device

Aug 9, 2011

I an doing device discovery and get the result as devices are unreachable and only 1 device among them getting discovered.Any inputs?

View 1 Replies View Related

Cisco WAN :: 1921 Cannot Get CCP To Discover

Oct 27, 2011

We are a small business that just bought a Cisco 1921 ISR. I am trying to set it up right now but I cannot get CCP to discover it. I am new to Cisco products and IOS.The router is currently set up in a test environment with a USB connection to a Win7 PC for console management. I also have the PC connected to gigabit ethernet port 0/1. I am using putty to access the console which I did with no problem for the initial configuration. After that I thought I would be okay to discover the router with CCP using the IP address I specified but then it prompted me for a username/password which I didn't see in the initial configuration. After this I did some research and found out I needed to set up a few more things so I ran the following commands: [code]

After this the video I was watching said to go in to CCP and specify the IP address or hostname of the router and use the login info that was just created admin/pw. When I ran the discovery I got the failure message: Connection to the device could not be established. Either the device is not eachable or the HTTP service is not enabled.When I run 'show ip interface' I notice 'Router Discovery disabled" is this why it is not working? How can I enable this or what else am I missing here? Am I not connecting to the router correctly? Oh and just for reference our plan is to have this router set up as a VPN gateway and firewall with 2 WANs for redundancy and connecting to our switch via an HWIC SFP for fiber.

View 14 Replies View Related

Cisco Wireless :: 3502 LAP Can't Discover WLC Using DNS

Feb 8, 2013

i have 2504 controller with 7.0.116.0 software and some 3502 APs. I also using 5 APs now and few days ago I bought some additional 3502 APs and I can't get them connected to the controller. My company admins decided to using DNS controller discovery instead of using DHCP option 43. I'm connecting APs to access ports of Linksys switches and APs not in the same subnet as ap-manager interface of controller. AP succesfully get IP and DNS from DHCP and could ping cisco-capwap-controller. However, I have such messages.

*Mar  1 00:12:32.014: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state.
*Mar  1 00:12:40.533: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
 
I can succesfully ping controller from AP AP30f7.0d2e.9a58#ping cisco-capwap-controller Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.23.16.30, timeout is 2 seconds:

View 6 Replies View Related

Cisco :: 5508 Will Not Discover AP's On Other Subnets

Nov 8, 2011

I have a 5508 controller that has 14 APs connected to it. I installed them without an issue. The 2 new APs are on a different subnet. I can ping them from the 5508 controller ping command, but they do not self discover from the web interface. The 2 new APs are at a differnet physical location.

View 21 Replies View Related

Cisco :: LMS 2.6 Possible To Discover Devices Through SNMP RW String

Nov 20, 2011

i am using cisco LMS 2.6. Is it possible to discover devices through SNMP RW string?as LMS is not doing so. is is deffendable for me to have two strings RO and RW for discovery of the devices ?

View 2 Replies View Related

Turn Off Discover - Ability But Allow Ethernet?

Oct 10, 2011

I have Windows 7 64 Bit Pro PC connected directly to the router via Ethernet.This is I will call Ethernet Connection 1.I also have a Windows XP Pro SP3 computer connected to the same router but via a wireless connection.I have both PC's connected together via an Ethernet cable. This I will call Ethernet Connection 2.It all works fine, but I only want my PC's to communicate via Ethernet connection 2.Currently, if I disconnect the Ethernet cable between the computers I can still access the files on the Windows 7 computer via the wireless connection on the Windows XP computer.I've tried to see if this is discoverable by other people using the router by installing Ubuntu on the Windows XP machine and looking at the available networks. Lo and behold, my Windows 7 machine is discoverable and accessible - albeit by a password. This is with the Ethernet cable between the computers unplugged.I have both networks on the Windows 7 machine set to public and all sharing options switched to off. Both computers have the same workgroup name. Worryingly I can still connect to the Windows 7 machine via Ubuntu wirelessly without even using the same workgroup name!All I want to do is connect the two computers via Ethernet Connection 2. I don't want any sharing information going to the router too and hence other poeple being able to see it. Ethernet Connection 1 on the Windows 7 machine is for the internet only (same as for the wireless connection on the XP machine).

View 1 Replies View Related

Discover Custom Internal IP Of Router?

Jan 21, 2012

Using a command prompt, how do I discover the internal IP of an unused router, which I set to a custom value and forgot? The router is not currently in use for internet access. I would like to access the control panel of the router without resetting it.I attached my netbook to the router with an RJ45 cable and disabled the netbook's wireless adapter to avoid conflicts with my current network. Using an elevated command prompt, I did an "ipconfig /release", rebooted and ran "ipconfig /all", but the gateway entry is blank. An "arp -a" returns 169.254.190.120 as the only interface. A "netstat -a" returns 169.254.190.120:xx...'s, 127.0.0.1:xx...'s, and 0.0.0.0:xx...'s, but no router internal IP address.Is there a way discover the attached device without resetting?

View 1 Replies View Related

Discover Security Key Of Wireless Networks?

Mar 5, 2011

I have a laptop but not the internet.But my neighbor has an internet router. I need to connect to that connection without the consent of him.

View 1 Replies View Related

Hp Mini Cannot Discover Wireless Network?

May 22, 2011

my hp mini is showing no network connections connect to the internet?

View 1 Replies View Related

Cisco LAN :: Catalyst 500 Express Switch / Discover Tool?

Jun 18, 2012

is there a discover tool for such a switch, i forgot the assigned ip .

View 2 Replies View Related

Cisco Switching/Routing :: Why Won't 3750 Auto Discover

Jun 6, 2012

I have a 3750 that when a client computer shuts down the switch will not discover it on start-up unless I bounce the switch.  Pretty dependable product so,.... did I miss something in my config? Switch is GBIC'd for Fiber?

View 2 Replies View Related

Cisco :: Unable To Discover Nexus 5548 With DCNM 5.2(2e)

Dec 20, 2012

I am unable to discover 2 Nexus 5548 with the SAN client of DCNM 5.2(2e)
 
These Nexus are used like LAN and SAN switch. Each Nexus is a SAN fabric. I would want to use DCNM in order to configurate the zone/zoneset via GUI. These Nexus 5548 run 5.1(3)N2(1b) release.
 
The Nexus ARE NOT managed  via the Mgmt interface (OOB) but they are managed via an interface vlan (InB)
 
I could not configure rightly

- the snmp-server user (SNMP user V1/v2 or V3 + group ? )  CLI on Nx

- to configure the discovery in order that DCNM discover each fabric either from web GU interface or java SAN client

View 1 Replies View Related

Cisco Switching/Routing :: How To Get DCNM To Discover 5548

Feb 21, 2012

I am trying to get our DCNM to discover the 5548. When I put my credentials for that appliance. I get this error .Failed Device x.x.x.x OS Version 5.1(3)N1(1) is not supported . The DCNM version we have is 5.2(1)S74.

View 1 Replies View Related

Cisco Switches :: SLM2008 - Filters Out DHCP Discover

Sep 16, 2012

I'm new on this site and having SLM2008 switches. I've been trying to solve the problem for quite a while, but so far I was unable to solve it. So here it is:
 
I'm trying to send IP TV from ADSL box (aka Free box) located in a small annexe of the house where the telephone line enters. Whole house is wired with 1Gb CAT6 cable. I'm using this wiring to get internet connectivity in different parts of the house and this works great. Now the idea was to create a separate VLAN on my 3 SLM2008 switches to get IP TV stream from ADSL box to the media box (also provided by ISP, aka Freebox HD). Different V LAN configs did not work for me: Free box HD would stuck on boot claiming it doesn't "see" the network. So then I've decided to go from simple things to more complex and removed the V LAN (came back to default config) and connected ADSL box with Free box HD with just one SLM2008 in between. Surprisingly it did not work! Same error on Free box HD! So I plugged the hub and started my Wire Shark to see what is going on.
 
First tried without the switch (just with a hub in the middle) and I saw successful connection:
1) Freebox HD send DHCP Discover
2) ADSL box responds with DHCP Offer
3) HD sends DHCP Request
4) ADSL issues a DHCP lease
 
Free box HD is ready to show any channel from ISP.
 
Secondly I plugged SLM2008 back and looked at traffic right after ADSL box: No DHCP packets seen at all! Then I moved hub next to Free Box HD and I saw it keep sending DHCP Discover every 30 seconds or so.... And it was not getting reply back.
 
So my conclusion is that SLM2008 for yet unknown reason would not let DHCP discover pass.... I've tried un managed Net Gear switch and *boom* Free box HD booted without a problem. I looked through SLM2008 settings and I have not found something relevant.
 
How to make my switch pass DHCP discover? If yes my next question would be how to configure V LAN on 3 switches to make it deliver IP TV to my TV set.

View 11 Replies View Related

Cannot Discover Computers In Network But Internet Works

Apr 30, 2012

I have a Belkin G wireless router. I have connected a Windows 7 PC using wired connection through Ethernet port.I've also connected my Windows XP PC through wireless connection. And plugged in my internet cable to the Router.Now I am able to access internet on both the PCs but I couldn't setup a network between the two computers for file sharing.

[code]...

View 2 Replies View Related

Cisco :: WS-C4507R+E Any Package To Install To Discover These Types Of Device

Jan 4, 2012

I tried to discovery WS-C4507R+E devices with lms 4.0 but the devices result unknown, any package to install to discover these types of device?

View 1 Replies View Related

Cisco Firewall :: ASA5540-AIP20-K9 / Discover Actual Product Part Number

Nov 16, 2011

how can i discover product actual part number from the device through console.I have a bought a cisco  ASA5540-AIP20-K9 and i want to check either is the product is shipped us as a right product.And i want to check total BoM requriements from entering the ASA console through any CLI Command.Below My Cisco ASA BoM which i purchased.
 
ASA5540-AIP20-K9ASA 5540   Appliance w/ AIP-SSM-20, SW, HA, 4GE+1FE, 3DES/AES1CAB-ACUAC   Power Cord (UK), C13, BS 1363, 2.5m1SF-ASA-8.3-K8ASA   5500 Series Software v8.31SF-ASA-AIP-7.0-K9ASA   5500 Series AIP Sofware 7.0 for Security Service Modules1ASA-VPN-CLNT-K9Cisco   VPN Client Software (Windows, Solaris, Linux, Mac)1Included:   ASA5540-VPN-PRASA   5540 VPN Premium 5000 IPsec User License (7.0 Only)1Included:   ASA5500-ENCR-K9ASA   5500 Strong Encryption License (3DES/AES)1Included:   ASA-AIP-20-INC-K9ASA   5500 AIP Security Services Module-20 included w/ bundles1Included:   ASA-180W-PWR-ACASA   180W AC Power Supply1Included:   ASA-ANYCONN-CSD-K9ASA   5500 AnyConnect Client + Cisco Security Desktop Software1CON-SU1-AS4A20K9IPS   SVC, AR NBD ASA5540 w AIP-SSM-20,4GE + 1FE,3DES/AES1 

View 6 Replies View Related

Cisco Switching/Routing :: DCHP Discover Packet Rate Limiting 6509s

Sep 11, 2012

We have a number of 6509s which generally have dhcp relay agents configured on the SVIs.  The dhcp servers are centralised.  Recently we've had one or two faults with misconfigured or faulty devices (blade server chassis and also printers) generating high volumes of dhcp discover packets and causing high cpu on the relevant 6500.  I would like to rate limit these discover packets, which are layer 2 broadcasts.  Storm control can't discriminate between different types of broadcasts and on a gig link would need to be set down at about 1% to have much effect on the problem.  I've looked at CoPP and also mls hardware rate-limiting but as I understand it, these two features don't control broadcast traffic. I also looked at dhcp snooping but if an interface receives a high level of dhcp discover broadcasts, e.g. over 100pps, I don't want it to go error-disabled (as this would knock down the whole edge switch),  just to drop the excess packets.

View 2 Replies View Related

Network Scan To Discover Rouge Apple Device Host Names

Sep 27, 2011

Anyway, I am looking for a way to discover host names of Apple devices (namely iPods and iPhones) that are on our network. I've tried a number of programs like Nmap, Advanced IP Scanner, and LanSpy to name a few. All of them will report back the MAC address with no problem but no dice on resolving the host name.

My goal is to use the host name to identify the device, and ultimately the person with the device. Any thoughts on how I can go about this? Is there a setting in Nmap I'm missing or perhaps a better program to use?

View 2 Replies View Related

Linksys Access Point :: E4200 Discover New IP Address Of Reconfigured Router

Feb 14, 2013

I have changed from a DSL internet service to a Comcast cable system.   I have setup my E4200v1 router as an Access Point, to extend coverage in my building.  It works fine, but I can no longer log on to  the unit using its'  IP address 192.168.1.1.  The browser returns the message "Internet Explorer cannot display the webpage."   If I want to tweak the settings the only thing I can think to do is to push the reset plug, back to factory settings and go through the whole process.   Is there a way to discover the new IP address of the reconfigured router?  I left the default address as it was when I made the changes to AP status. 

View 1 Replies View Related

Linksys Wireless Router :: X3000 Some Wifi Clients Can't Discover Connection

Nov 23, 2012

I've just upgraded my home wireless from an NetComm NB5540 + modem to a LinkSys X3000.Internet access works fine for all devices, but some wireless devices can't "see" my Win7 desktop system that's on a wired connections to the router. Galaxy Note phone (running ICS 4.0.4) can discover and connect to file shares on my desktop system without any problems.Asus Transformer Prime tablet (running JellyBean 4.1.1) can see the router on the local network, but can't see my desktop. Even if I manually type in the IP address it can't connect to itLikewise my old WinXP laptop can see the router but can't see or connect to any other devices.
 
I tried connecting the NetComm router with just Wifi configured to one of the ethernet ports on the X3000, so I've got two Wifi networks running in parallel. If I connect to this second WiFi network with any of the above devices then they can all discover and connect to my desktop system on the wired connection to  the X3000.

View 1 Replies View Related

Linksys Wireless Router :: E4200v2 - Unable To Discover Any Setting In Browser

Mar 15, 2012

I'm able to use the web interface to the router, from one computer (Windows XP, IE 8). But from my other computer (also Windows XP, IE 8) I can log in to the router, but then the browser just presents an empty screen. I haven't been able to discover any setting in the browser that could cause this. From this same computer, I can access the web interface with no problem, using Google Chrome browser! So the problem seems to be in IE.

View 3 Replies View Related

Cisco WAN :: T1 Cards In 3845?

Apr 21, 2013

I am replacing our core router, which is a very old 7204VXR, with a T3 card in it.  We are using it to terminate about 10 point to point T1's.  It is also the central gateway for our entire network.
 
I am planning on replacing it with a 3845, and an NM-1T3/E3 card for my DS3.  I think I've got that part worked out.
 
My real question is concerning future upgrades.  We are trying to convert many of these point to point connections to Metro Ethernet, and get rid of the huge DS3 cost.  When that happens, I'll probably have a handful of point to point T1's left over (maybe 2-6 of them).  So, what I need is a good solution to terminate those 2-6 PTP T1's in my 3845.  In the past I have just been using the old WIC-1DSU-T1-V2 cards to terminate my T1's.  I am looking for a solution that won't break the bank.  I looked at both the HWIC-4T1/E1 and the NM-8CE1T1-PRI cards (which terminate 4 and 8 T1's), but they are like $4,500 and $8,500 respectively.  That's way beyond my budget for these.  I definitley don't need a card that will do PRI's (DSP's etc.).  I just need it to terminate plain old point to point T1's.
 
So it may be that I'm just looking at the wrong cards.  Or maybe the make cards that will go in the back of the 3845 that will house 2, 4 or more WIC slots, and I could just use WIC-1DSU-T1-V2 cards? 

View 6 Replies View Related

Cisco WAN :: Difference Between ES20 And SIp Cards?

Feb 5, 2012

I am pursuing a case of Cisco 7600 where the customer has asked me to highlight the major difference between teh new ES20 line cards and the SIP 400 cards

View 0 Replies View Related

How To Set Up Two Sound Cards In One Pc

Jan 19, 2013

How to set up two sound cards in one pc.

View 1 Replies View Related

Use A PC With Two Network Cards?

Nov 2, 2012

I need a cheap router that can route between two ranges.

10.10.6.x
and
10.10.7.x

I don't want to use a PC with two network cards....I just need something cheap and simple.I was wondering whether any low to mid end consumer routers allows you to assign IP addresses for ethernet slots, or even create VLANs..?

View 6 Replies View Related

Cisco Switching/Routing :: 6509E With 2 Sup 2T Cards

Apr 30, 2012

I have a new 6509E with 2 sup 2T cards. The 10GE ports on both sup cards will connect to 2 5548s. Can i connect the management interface on the new 6509E to the old 6509 until i free up space to bring the line cards over?

View 2 Replies View Related

Cisco WAN :: 2811 Can Support BRI And PRI Cards At Same Time

May 2, 2012

I wish to use a VWIC2-2MFT-T1/E1 and a VIC2-2BRI-NT/TE in a 2811 -can they co -operate at the same time

View 3 Replies View Related

Cisco WAN :: 3945 ISR Not Recognizing WIC-1DSU-T1-V2 Cards

Jul 18, 2011

Was wanting to know if these cards are compatable with the new 3945 ISRs or if their is a unique command that has to be run to recognize these. why I'm using these large routers with a T-1. Its too long of a story.

View 2 Replies View Related

Cisco WAN :: 3945 Router And E3 / T3 Network Cards

Aug 11, 2011

I just got my first  3945 router and E3/T3 Network cards and when I do a sho ver I can see the E3/T3 card but when I do a show run all I see are the 3 GE interfaces.

View 1 Replies View Related

Cisco WAN :: 2811 / 1841- Cannot Get These Cards To Show Up

May 4, 2011

I have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
 
So I am guessing I need a different IOS.

View 1 Replies View Related

Cabling / Cards :: Use On - Board Lan?

Sep 8, 2012

I've got on-board LAN but I don't know how to use it. Am I meant to be able to surf the internet just like that if i have got on-board LAN???

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved