Cisco WAN :: 2811 Can Support BRI And PRI Cards At Same Time
May 2, 2012I wish to use a VWIC2-2MFT-T1/E1 and a VIC2-2BRI-NT/TE in a 2811 -can they co -operate at the same time
View 3 RepliesI wish to use a VWIC2-2MFT-T1/E1 and a VIC2-2BRI-NT/TE in a 2811 -can they co -operate at the same time
View 3 RepliesI have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
So I am guessing I need a different IOS.
i need to use two modems connected to different virtual networks at the same time on one pc.the pc is having two lan cards. i tried using different ip address for both the modems.they are pinging but web pages are not opening.i tried using different browsers for opening web pages of the virtual networks but they are not opening.
View 1 Replies View RelatedIs it possible to have a WLAN only be active during set times of the day?.I have a WLCM in a 2811 router but I can't find any type of setting that will let me enabe a WLAN at 6pm and disable it at 7am.
View 3 Replies View RelatedI would like to transport two time slots (TDM traffic) over an IP network in order to connect two telecom devices located in different sites, i have cisco 2811 routers on both sites with ip advanced services 12.4.20T IOS
View 5 Replies View RelatedTo determine if the 2811 and 1811 ISRs support Verizon or Sprint USB 3g modems?
View 1 Replies View Related[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies View RelatedI read the document, [URL]
[
Q.I have Cisco 6700 Series line cards today with Centralized Forwarding Cards (CFCs). Are these line cards supported in a Cisco Supervisor Engine 2T system?
#
A. A Cisco Supervisor Engine 2T system will support all Cisco 6700 Series line cards with CFCs.
]
So, As long as the 67XX line card is using CFC, it is compatible with Sup-2T.
I also find the IOS release note indicate the 6704-10G with CFC is supported by Sup-2T, but it require 512M memory.
[URL]
The bug details is not disclosed. So I further search what the default memory size of the WS-F6700-CFC is, then I found here says it is only supported by Sup720 and no memory upgrade option, which means must upgrade to DFC4, in another words, it is not compatible with Sup-2T
[URL]
WS-F6700-CFC:
Centralized Forwarding Card (CFC) for use on WS-X67xx Ethernet modules. This daughter card is supported only by the Supervisor Engine 720. There are no memory options for this daughter card. default memory: 256M
So my question is: whether “WS-X6724-SFP with CFC” and “WS-X6704-10G with CFC” compatible with Sup-2T without upgrading to DFC4 daughter card, and do they support in VSS-2T?
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies View RelatedAssuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
I need my ASA 5505 to support ESP-AES-128-SHA on 2 dynamic clients, one with PFS and another without PFS. I add 2 dynamic maps like this. [code] Now the client without PFS can be connected, but the one with PFS cannot.How can I set the dynamic maps so that they can support both clients at the same time?
View 3 Replies View RelatedI want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third party Like [URL]
View 1 Replies View RelatedI just want to Know how many users can connect to AIR-CAP3602I-x-K9 at singel point of time.
I am currently facing Threshold errors In 1140 AP where we can see that 12 client is recommended by cisco [URL]
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedCiso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedMy setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies View RelatedI need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
I am replacing our core router, which is a very old 7204VXR, with a T3 card in it. We are using it to terminate about 10 point to point T1's. It is also the central gateway for our entire network.
I am planning on replacing it with a 3845, and an NM-1T3/E3 card for my DS3. I think I've got that part worked out.
My real question is concerning future upgrades. We are trying to convert many of these point to point connections to Metro Ethernet, and get rid of the huge DS3 cost. When that happens, I'll probably have a handful of point to point T1's left over (maybe 2-6 of them). So, what I need is a good solution to terminate those 2-6 PTP T1's in my 3845. In the past I have just been using the old WIC-1DSU-T1-V2 cards to terminate my T1's. I am looking for a solution that won't break the bank. I looked at both the HWIC-4T1/E1 and the NM-8CE1T1-PRI cards (which terminate 4 and 8 T1's), but they are like $4,500 and $8,500 respectively. That's way beyond my budget for these. I definitley don't need a card that will do PRI's (DSP's etc.). I just need it to terminate plain old point to point T1's.
So it may be that I'm just looking at the wrong cards. Or maybe the make cards that will go in the back of the 3845 that will house 2, 4 or more WIC slots, and I could just use WIC-1DSU-T1-V2 cards?
I have installed LMS 3.2.1 and RPM(ATM technology) can be seen but not ML card(ONS). Also LMS discovered lot of interfaces (int vlan) one of the core switches and marked them as 'unreachable'. How can delete these when LMS marked as unreachable?
View 1 Replies View RelatedI want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies View Relatedi have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies View RelatedI have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies View RelatedI am pursuing a case of Cisco 7600 where the customer has asked me to highlight the major difference between teh new ES20 line cards and the SIP 400 cards
View 0 Replies View RelatedHow to set up two sound cards in one pc.
View 1 Replies View RelatedI need a cheap router that can route between two ranges.
10.10.6.x
and
10.10.7.x
I don't want to use a PC with two network cards....I just need something cheap and simple.I was wondering whether any low to mid end consumer routers allows you to assign IP addresses for ethernet slots, or even create VLANs..?