I need my ASA 5505 to support ESP-AES-128-SHA on 2 dynamic clients, one with PFS and another without PFS. I add 2 dynamic maps like this. [code] Now the client without PFS can be connected, but the one with PFS cannot.How can I set the dynamic maps so that they can support both clients at the same time?
View 3 RepliesI wish to use a VWIC2-2MFT-T1/E1 and a VIC2-2BRI-NT/TE in a 2811 -can they co -operate at the same time
View 3 Replies View RelatedI just want to Know how many users can connect to AIR-CAP3602I-x-K9 at singel point of time.
I am currently facing Threshold errors In 1140 AP where we can see that 12 client is recommended by cisco [URL]
I have two sites that each have asa 5505's and each have dual ISP's. Currently I'm using sla monitor to failover to the secondary line when there is a detected outage. After this sla failover occurs which seems to be instant, secondary ISP re-establishes the VPN. This process takes about 30 seconds. My thought is that the side which is healthy does not detect the outage due to a preset amount of timeouts and thats where this 30 second delay comes in to re-negotiate the VPN tunnel. can I create a smaller window of time to heartbeat between the two so that the VPN outagage is detected in around 5-10
View 3 Replies View RelatedI have a Cisco ASA 5505 Firewall. I am using windows VPN. I have configure IPSEC/L2TP Vpn. And now i hv some problem..
1) VPN is connected but I notices that VPN client connection gets in "HANG" mode after couple of minutes.
2) I am getting error when i try to connect my SQL Server (windows 2008) [code]
I currently have a problem where I have to constantly reboot my ASA whenever my cable modem reboots. The ISP (Pen Tele Data) is setup so that my ASA has to obtain its' static IP using dhcp (ip address dhcp setroute) on the outside interface. Now, I also have another location with a cable connection (Comcast) that does NOT experience the same problem. However, the difference is this ISP allows me to assign my static IP directly on my outside interface. What can I do so that I don't have to reboot my first ASA everytime modem reboots.
View 6 Replies View RelatedI am going to update my Windows Small Business Sercer 2003 to 2011.I currently have an ASA 5505 with the IPS installed on it. I am reviewing the migration procedures from Microsoft. Within the procedure it asks if the firewall or router supports UPnP. Does my ASA 5505/IPS support UPnP?
View 2 Replies View Relatedi have asa 5505 adaptive security plus. and i have only 3 vlans . outside , inside , DMZ restricted.so it's working fine but i want to connect to my inside another private network, or do i need to buy License.and how i can activate the license key.
View 4 Replies View RelatedDoes the ASA 5505 will allow the addition of a 2nd external link to its configuration? I know the device is capable of Redundant or Backup ISP Links, but that’s not what I need. I will have two different links for two different purposes. Currently we are using the ASA 5505 just for Internet access, so only the ISP link is connected, very basic configuration. We are planning a connection to a client’s global (MPLS) network and we need to be protected against any traffic coming from that network, ergo we need to use a firewall for connection to that external link.Now with the final configuration the Internet traffic must keep being routed to the ISP link, and some other traffic must be routed to the new external link. Can the ASA 5505 be configured for this scenario?
View 7 Replies View RelatedI want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedCiso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI use a DSL internet and i am assigned a new ip everytime my modem is restarted. I want to use the same ip everytime either through changing it or any other way. I mean can i use my own ip?
View 3 Replies View RelatedAny software to measure Authentication time between client and Radius serverr.
View 8 Replies View RelatedLooking to upgrade our 5508 WLC to the newest code AIR-CT5500-K9-7-2-103-0-FUS..We are currently running an older code 6.0.196.0..Are there any issues that I need to worry about with this upgrade ?Do I need to upgrade the AP's at the same time ?
View 7 Replies View Related4GE SSM just have only additional ports with Ethernet (RJ-45) or SFP (fiber optic) Can I config 2 ports use default type (RJ45) and config 2 ports use SFP ?
For Example.
G1/0 and G1/1 = Default type
G1/2 and G1/3 = Media-type sfp
G1/0G1/1G1/2G1/3G1/0G1/1G1/2G1/3RJ45RJ45SFPSFP
I have installed the ACS 5.1 and linked to my WLC, and when I enter my Logeo I agree Signature: User and password whenever you want from different devices, I want to do is only allow a user to one session at a time.
View 7 Replies View Relatedis 633+ seconds (approximately 10 minutes) load time normal for a Cisco 7204 router? I find that it takes forever for the router to do :Self decompressing the image". I tried the latest IOS and tried different bootloaders but it doesnt seem improve it?
View 2 Replies View RelatedOn the CLI, we have ACS showing:
clock timezone Etc/GMT-6
!
ntp server 10.10.10.1
A show clock shows the correct local time. When in the GUI of ACS the clock reads
Tue Aug 30, 2011 21:13:58 GMT+06:00
A customer observes SNMP timeout problems on a Cat6500 with IOS 12.2(33)SXI. As a result every 2 days (more or less) all interfaces are marked DOWN and a couple of minutes later all interface are up again - but in fact there is no interruption, it is just the snmp request getting a time out. the customer does not have problems with IOS 12.2(18)SXF14.
In the Bug Details the "Known affected versions" lists the following beside others:
12.2(33)SXI
12.2(33)SXI1
12.2(33)SXI2
[code]...
Now I am confused; both IOS versions are listed as affected (12.2(33)SXI and 12.2(18)SXF14) but the customer does have problems only with one version. Is the customer hitting this bug or is it another one ?
He upgraded 2 Cat65xx on which he observed the problem to IOS 12.2(33)SXI6 and the problem is gone; is this just a coincidence or is CSCed52841 really fixed in 12.2(33)SXI6. This version is not listed as affected but on the other hand, "Fixed-In" lists only these 3:
12.1(22.3)E1
12.2(17d)SXB5
12.2(18)SXD
Before going to upgrade around 50 Core / Distribution switches the customer wants to be sure with the IOS version. Tracing the issue is not that easy because the failure occurs only from time to time.
I have a Cisco 857W router which I have aquired without cost. I want to use the wireless abilities of this router to be the wireless point to get into my home lab while I am studying for my CCNA and beyond.
I have erased it to its factory settings. There is no ADSL connection to it just yet, I might connect in to my internet connection another time. Not just yet.
I dont even know where to begin. I have searched all the internet and there is nothing really anything there to guide me to set it up from the very beginning.
I logged in first time with default user ID and Password i.e.,cisco then I did wr erase and reloaded the router but I didn't change the one-time password in ISR 2911.Now its asking for user name and passworkd and cisco doesn't work.Now from ROMMON mode if I change to 0*2142 and reset it will again come back to ROMMON mode.From ROMMON mode if I type boot will come back to normal mode and ask for username and password.
View 4 Replies View RelatedI am running Wondows XP OS and have 2 NIC's in it. One is connected with DSL and other is with LAN of my Network. By using CCProxy 6.4.1 I am running the Internet on my LAN. I also want to run CCTV camera Sevice and want to share it on LAN as I share Internet on LAN but Camera Service Packets do not route on LAN but routhe when i disconnect the DSL Connection. So what i have to do to run both services (internet + camera service) smoothly.
View 1 Replies View RelatedI have two wireless adapters "PCI Marvell Libertas" and "USB Sagem" and i have access to 2 different AP's, The browsing' seem to be a little slow while i'm downloading', and my work requires lot's of downloading', as i have managed to connect to my two different AP's at the same time, i always feel like i'm usin' only one of 'em, so i was wondering' if i can take advantage of both connection in order to double the speed, and or if there's some way to use one for browsing' and the other for torrent downloads only.i've tried to mount the USB adapter on Linux using' Vmware, but it keeps saying' unable to get IP address,,However that's not the problem,, all i want to know is if there's a way to make both connection work on windows 7 Ultimate X64,
View 1 Replies View RelatedI have two wifi networks in my home, 1 has the internet wifi signal and 2 is my personal network. How can I use the internet signal from one whilst staying connected to my own network.the net sifi signal is from a virgin media superhub, and my personal wifi network is using an asus rt-n65u which has a wds mode not sure if this
View 9 Replies View RelatedI have a PC that is connected to LAN network and I have USB 3g Modem when i try to connect them both my pc use only ether LAN or Modem what should i do to make them both work at same time? Running windows 7 64x
View 1 Replies View Related