Looking to upgrade our 5508 WLC to the newest code AIR-CT5500-K9-7-2-103-0-FUS..We are currently running an older code 6.0.196.0..Are there any issues that I need to worry about with this upgrade ?Do I need to upgrade the AP's at the same time ?
View 7 Replieswe have the issue that a new WLC 5508 has been installed in a new location. Unfortunaltelly we have no hands-on suopport on-site, so just remote connection.Now we figured that the service-port and management interfaces have to be reconfigured. In case we can not reach the WLC with the new configured interfaces it would be useful if the WLC reboots automatically after time x to reload the previouse working configuration.So the question is, is there a functionality to create a script which reboots the WLC automatically after time x?
View 4 Replies View RelatedI have a 5508 WLC and a series of 1140 APs. One small but annoying thing I have noticed is that the APs are pulling the correct time from the WLC but the timezone is off so they are showing time at 0 and not -8. The timezone is set and correct on the WLC.
View 9 Replies View RelatedIs it possible to rename the default webauthentication URL from [URL] to something like [URL]. We are running on 7.0.98.0, is it possible to do http for web authentication and https for Mgmt access if we upgrade the controller software?
We configured our guest wireless with no layer 2 authetication so users can associate with an AP and get an ip adress but they can't go anywhere unless they have a valid username and password(web authentication) - does this affect the performance of an AP since there will be many people associated with each AP, is there any setting in the WLC to de associate a client from an AP if its idle for certain time.
I would like to set a time limit for how long a client can be continously connected to the WLAN that provides my guest internet access. The user name/password is hosted on my ACS and authentication is provided by my Cisco NAC. I am using 5508 controllers (7.02) and WCS.
Somewhere in this combination of stuff, there has to be a way to set a two hour time limit.
Looking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
Recently i have setup a WLAN with inside and anchor 5508 controllers. Standard setup. However, one issue I have is I wish to extend the length of time between password changes for users connected in on the guest wlan. At the moment, 30 is max. I dont have an option on the controller to creat accounts for any longer than that. How to I extend it to 90 days or 120 days?
View 1 Replies View Relatedupgrade from 7.0.235 to 7.0.240? I can't go any higher right because we are still using WCS. I read the white papers but as far as I can tell there are no new features..
View 3 Replies View RelatedI have a main with one WLC 7.0.240.0 and have acquired a HA with 7.3. I have considered whether to put on both WLC version 7.3 or 7.4.:
first, that there are differences between the two versions?
second: As I read, the version 7.4 can make backup of several WLC, this function is already available?
Does WLC 5508 has capability to create login credentials with specific time of validity? Could it be used in hotel set-up to provide prepaid access account to guest?
View 2 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
I am planning to upgrade WLC from 7.2.103.0 to 7.2.110.0 due to some bug, but I wanted to know if it is compatible with WCS - 7.0.240.0 and NAC Guest server version 2.1.0, I am made some search but I couldn't get to proper conclusion.
View 8 Replies View RelatedIn order to enbale HA SSO on our two 5008 WLC's, I plan to upgrade them to 7.3 / 7.4 (currently 7.2)Right now 7.3.112.0 is the latest release. We do not have any 1600 series AP's, which requires 7.4.any reason going for 7.4 directly..or not going for it?
View 5 Replies View RelatedI am planing to upgrade 2 of my 5508 series WLC from 7.0.116 to version 7.2.111.3. I understand that legacy AP's are no longer supported. Is the upgrade straight-forward just like other code upgrades?
View 19 Replies View RelatedI want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Can I make that jump or should I do incremental?
View 7 Replies View RelatedWe are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Upgraded from 7.0.98.0 to 7.0.220.0 and any issues during the upgrade or after the upgrade?
View 3 Replies View RelatedWe are planning to upgrade our controller 5508 from 7.0.116.0 to 7.1.91.0. Is this directly possible or i have to put some other image before directly upgrading it?
View 7 Replies View RelatedWe recently received a couple of new 5508 WLC running 7.2.103 but the FUS is running 6.0.182. Is it possible to upgrade the FUS to 7.0.0 remotely? Looking at the FUS release notes, user intervention is no longer required, Is this possible?
View 10 Replies View Related5508 W LAN controller with 50 AP License upgrade from 7.0.220 to 7.4 is it will effect to the license and configuration? Because the license came pre- installed.
View 1 Replies View RelatedI want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View Relatedi'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
I have an AIR-AP1242AG-E-K9 which had c1240-k9w8-mx.124-21a.JA loaded, I followed the link below and upgraded with Cisco’s upgrade tool to c1240-rcvk9w8-mx with no problems at all, after the upgrade I could then see the LWAP on the 4402 controller and had it working a treat.Now the problems begin, I brought it into the office where we have 5508 controllers, plug in the LWAP into our management switch and boot it up I get an IP assigned from the DHCP server and the AP goes into discovery mode but never finds the controller.I have logged the boot process but this does not give much away, our other 1100 series AP’s boot fine,
[URL]
Console Boot Log.
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
[code]....
And that is where she sits and does nothing more, I have noticed the DNS problems but the other 1100 series LWAP’s boot up after show that same issue.
I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies View RelatedI have a 5508 wireless controller running version 6.0.199.4 (the image installed when the device was shipped) and I am trying to install by tftp version 7.3.112.0
The issue is when using tftpd32 gets to 82% transfered then fails with the error "% Error: Code file transfer failed - Error while writing output file"
One week ago I use a WLC 5508 to place and replace another WLC 5508 with version 6.0.199.4, when I conect the new WLC all AP´s works OK only 10 dont work and not are recognizes from the WLC with version 7.3.101.0. The fail is the radios stay disabled. All ap´s are AIR-AP1242G-AK9 . See the image below, the only difference this ten AP´s are conected in switches cisco all the rest are connected in switches of ohter vendor. If possible some command in the configuration is not neccesary and make the bad function?This is tipically config apllied by the customer in they cisco switches interface GigabitEthernet0/22description PB-RS-A22switchport access vlan 5switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable?
View 4 Replies View RelatedAfter upgrading my 5508s to 7.2.110.0, they are reporting mobility data path errors to one of my WiSMs running 7.0.235.0.
I get these messages on the 5508s reporting that it can't send a ping to the affected WiSM:
*ethoipSocketTask: Aug 08 21:15:41.175: %ETHOIP-3-PKT_RECV_ERROR: ethoip.c:341 ethoipSocketTask: ethoipRecvPkt returned error
*ethoipSocketTask: Aug 08 21:15:41.175: %ETHOIP-3-PING_RESPONSE_TX_FAILED: ethoip_ping.c:312 Failed to tx a ping response to <ip address>, rc=5
But maybe there is another clue because I also see in the same log these errors referencing the same WiSM:
*bcastReceiveTask: Aug 08 21:15:45.310: %LOG-1-Q_IND: mm_dir.c:1969 Failed to recreate the SSH Rule for <ip address>.
*mmSSHPeerRegister: Aug 08 21:15:44.829: %MM-1-SSHRULE_CREATE_FAILED: mm_dir.c:1969 Failed to recreate the SSH Rule for <ip address>.
Why is the controller trying to SSH to another controller? Was some SSH related feature added to 7.2 that has been accidentally enabled?
I have a 5508 controller, just upgraded from 6.0.182 to 7.0.98.0. Also LAG was switched off directly after upgrade.
Since the upgrade none of the 1142 LAPs are associating with the controller. I can see they are being issued IPs by the internal DHCP but putting a console cable and watching I am getting:
Not in Bound state.
*May 4 11:41:17.759: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*May 4 11:41:17.759: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
One Ap prior to the upgrade was on a static IP and that connected through without any problem, (it was an 1131 though, but I dont think that is the issue...)
We have few sites with old 1232 ag AUTONOMOUS existing AP's , They are connected through 1 mbps link to main office .Now we are planing to upgrade with WLC 5508 and few 1140 ap . but we want to use these same 1232ag ap on some sites.So we need to upgrade it to LWAP .
1>Is it possible to upgrade this model of AP
2>Which is the ios i should download , is it avaliable in cisco site (as this ap is end of sale now )
3>How the step to upgrade this autonomous ap
Just recently upgrade our 2 5508 controllers from 6.0.199.0 to 7.0.116.0. Since that upgrade, I have a handful (8 to 10) of wireless laptops that now refuse to associate to any access points. The thing these laptops all have in common is some variation of the Intel Wifi Link AGN cards. I have about 200 other clients out there working just fine.
I've tried everything under the sun that I can think of. Patches, drivers, the whole sh'bang.
Is there a known issue with 7.0.116.0 and these particular cards?
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedCiso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View Related