I have installed the ACS 5.1 and linked to my WLC, and when I enter my Logeo I agree Signature: User and password whenever you want from different devices, I want to do is only allow a user to one session at a time.
View 7 RepliesI have a user authentication issue with our WLAN deployment. My issue relates to the guest access WLAN. First a brief descrition of our setup. We have a local WLC in the branch office (5508) with two SSIDs configured, CorpNet for the internal network and GuestNet of external guest access. We also have a WLC (5508) in the DMZ to provide the guest access. We are using Cisco ISE server to authenticate guest users via a web portal.
The authentication process works as it should. An external client gets an IP in the DMZ and is redirected to the web portal to authenticate their account. When they do they are able to access and browse the internet. No problems. My issue is that if we disable their account (ie suspend or delete it) in ISE it does not seem to terminate the users session and they can continue to have internet access. What I would like to happen is that when the account is disabled in ISE then the associated device's access to the internet is removed.
How can I check I have the right vpn time on a VPN client session on a asa 5510 , and how can I modify it to more time...
View 3 Replies View RelatedWe have Cisco WLC 7.0 with private and public accesses. Is it possible to limit guest session time? For example, any visitors’ connection will be disconnected after 1 hour.
View 3 Replies View RelatedI am running a guest wireless network on a Cisco 5508 WLC with 6.0.202.0 code. My syslog is filling up with the following error message:
WLC: *May 15 12:32:59.244: %AAA-3-VALIDATE_GUEST_SESSION_FAILED: file_db.c:3968 Guest user session validation failed for guest_user10. Index provided is out of range..
The user that is assigned to the guest_user10 account works fine and has no idea this error is occurring.
This error message is occuring exactly every 15 minutes 24x7.
I believe I have a rogue user who has setup a device to try and login to the guest network automatically, every 15 minutes with the guest_user10 credentials. I need to track this device down. I need a way to find either the MAC or IP address of the device that is causing this error message. I have tried turning on AAA debugging on the controller but I dont get anything more than the above error. I have also tried using WCS to look at the client history but it only show the normal activity.
i have user connected to office using Cisco vpn client , Cisco asa 5520 acts as vpn gateway, frequently the users got disconnected from the server while the VPN still established and not disconnected!
what is the cause of the issue , where the fault is located ? how to start the troubleshooting to figure out the issue?
I am configuring remote access VPN on a cisco router 3845. Works fine.
I was looking for configuring session and idle time configuration for groups and eventually users.
I am using the following Cisco VPN remote access configuration :
crypto isakmp client configuration group mygroup
key xxx
pool mypool
acl 101
max-logins 3
banner ^CHelloo ^C
Is there any command in cisco ios similar to Cisco ASA vpn group 1 session-timeout?
Cant we create a guest user login with more than 30 days lifetime? In the lifetime field we can enter maximum 99 but it only allows up to 30
View 5 Replies View RelatedWe have dialup users that are connecting to our portal for uploading/downloading credit information. We are currently using ACS 3.3. There is a requirement that, initially we provide clients with their username/password, but we want to enforce the policy that when the user logs in first time, he should be prompted (forcefully) to change his password.
1) Can this be done in ACS 3.3
2) What solution shall be used in this case ? can it be done in ACS 5.3 ?
I want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies View RelatedWe are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedWe are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedIs it configurable to allow wifi user to user traffic on WLC 5508?
View 4 Replies View RelatedCiso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
how to reset old TCP session on cisco ASA 5520?
View 2 Replies View RelatedIs it possible to log when a user connects/disconnects their VPN session? They are connecting to an asa 5510.
View 5 Replies View RelatedI have Any Connect (ver 3.1.01065) configured on Cisco router 891. VPN is working fine from the desktop, but I also need the ability to establish a VPN connection through a RDP connection (i.e. I'm using RDP to connect to a PC which has AnyConnect installed on, then trying to establish a VPN connection). OS Windows 7 SP1 x86.I've read about changing some settings in profile file (changed the <WindowsVPNEstablishment> option to "AllowRemoteUsers". Then applied the profile to the relevant Group Policy. Connected VPN from the PC (not through RDP), so that it downloads the new profile, and then disconnected again.): url...
But this make sense to the cisco asa... I have a cisco router on the ios 15.1. I've checked the XML file on the local PC to confirm the profile has been downloaded and is has, and I can't see the AllowRemoteUsers option.So I still can't start VPN through an RDP connection. (Error is "VPN establishment capability from a remote desktop is disabled. A VPN connection will not be established".)This also happened with the previous version of AnyConnect (2.5.xxxx).The PC's local routing tables look fine, and I can't see any conflicts that would cause the RDP session to drop.In the main window of Cisco anyconnect secure mobility client Ive noticed label: Web Authentication required.
i have a question regarding the monitor session command. I have following interfaces on my router:i want to monitor the traffic from the source interface Gi0/2 to the destination interface fa1/3,monitor session 1 source interface gigabitEthernet 0/2 brings this error message % Incomplete command.,monitor session 1 source interface gigabitEthernet 0/2?/ : <0-2>,i don't have any ports on the Gigabit Interfaces. Any ideas how to monitor traffic?
View 1 Replies View RelatedI have configured my Cisco 881 and finally got past the "Cannot see my network" with IPSec VPN issue.I have a usecase where I need to access the gateway from the VPN Session.When I connect to the VPN using Cisco VPN Client 4.8x, I do not get back a Default Gateway on the VPN Adapter. When I try to ping my LAN Gateway IP (10.20.30.1) it does not respond and I cannot access it with any other tools.I am pretty sure this is a very ACL issue and it makes sense to hide the gateway by default but the big question is how do I configure my router to see the Gateway and be able to access it from the VPN session?
Network Info:Internet Gateway to ISP: 192.168.68.1DNS: 192.168.2.1WAN Address for Cisco 881: 192.168.68.222LAN Address on Cisco 881: 10.20.30.1DHCP for LAN on Cisco 881: 10.20.30.10 - 10.20.30.50DHCP for IPSec VPN: 10.20.40.10 - 10.20.40.50
Is it possible to know the VPN usage for a particular session using Cisco ASDM 6.4? Device type is ASA 5550. ASA version 8.4
View 4 Replies View RelatedIPSEC VPN users are using ACS for extended authentication, whenever authentication is made, entries are available on ACS, now i need the session duration info on ACS, that means total time during which the user was active should be available.
i have enabled accounting globally on the ASA firewall through aaa accounting enable console ACS and also enable accounting in the tunnel-group itself, to which the user is using.
on ACS 5.1 ,i could not find any option / TAB that can give some information on the session duration.
What command sequence disconnects you from a TS session? My setup is as followsr1 > TS > 2009-2621XM 2010-3825-R1 2011-3825-R2I can connect from the TS to any of the devices. The issue is that I am telnet'd to r1 and from there telnet'd to the TS. So when I type "Crtl+Shft+6, x" I go directly back to r1 and not the TS. Furthermore if I resume the session on r1 the TS is still connected to whatever session I was in prior to disconnecting. I've experimented with the disconnect and escape characters but I'm at a loss what it is that changes this.
View 4 Replies View Related"how to monitoring VPN Login Session?" I want to the history of VPN User login to my VPN. How could I know?Which software can made me easy to monitoring and store those log in my SNMP Server? How to do that?
View 1 Replies View RelatedI have inherited the support of an ASA5520 running 8.0(3)12 code and I believe I have a pretty simple question here that I haven't been able to figure out on my own. I have a few users that connect to the box via IPSEC VPN client connections. They want to be able to leave up a RDP based connection, for monitoring purposes, for a most of the day, but thier RDP connection keeps getting discounnted after a few hours. The VPN connection never gets disconnected, just the RDP session running through it. I have another box running 8.0(4) code and they can leave up the RDP sessions as long as they like without getting disconnected from the server(s). I have compared the configs of both boxes and don't see any glsring differences in regards to the configuration that would cuase the RDP sessions to either to stay up or be disconnected after an inactivity type scenario.
What to look for in regards to identifying the timer that is disconnecting the RDP session after a period of time.
I will use function of span in sup70-3b.How many session can use in sup720-3b? For example, 2 or 4 session.
View 1 Replies View Related