I have a PC that is connected to LAN network and I have USB 3g Modem when i try to connect them both my pc use only ether LAN or Modem what should i do to make them both work at same time? Running windows 7 64x
View 1 Replies
My laptop connected to the LAN for internal access, the LAN is limited access ( limited permission for internet connection), so I bought USB Modem. But when i connect to USB modem I lose my internal connection. ( I want to use LAN for internal access and USB Modem for Internet access at the same time)
View 2 Replies View RelatedI have a smc wireless cable modem gateway router lease is set to expire every 7 days does it matter if its like more often, is this good enough, i was told every day might be better as i get better connection.
View 2 Replies View Relatedif there's any way to track the time or date when my modem was used. I have a TP Link modem/router.
View 1 Replies View Relatedif I am XP and online, if I restart into Win7, I have to power cycle my modem before I can go online. If I then restart any number of times into Win7, there is no connections problem. If I then restart into XP, then I have to power cycle the modem again. If I then restart any number of times into XP, then there is no problem. If I then restart into Win7, then I have to power cycle the modem.
View 1 Replies View RelatedI usually put some stuff up for downloading and go to sleep. Now I setup my computer to auto-shutdown at a particular time via cmd, but I want o know whether it is possible for me to put some time settings in my modem+router so that it switches off at a particular time or something like that.Then when I get up next morning, start using it again. I don't want to keep my router on after it's not needed. Also I don't wanna keep it vulnerable after it's not needed, even though I have set it up quite securely. ( WPA2 PSK, and MAC filtering)
View 5 Replies View RelatedI currently have a problem where I have to constantly reboot my ASA whenever my cable modem reboots. The ISP (Pen Tele Data) is setup so that my ASA has to obtain its' static IP using dhcp (ip address dhcp setroute) on the outside interface. Now, I also have another location with a cable connection (Comcast) that does NOT experience the same problem. However, the difference is this ISP allows me to assign my static IP directly on my outside interface. What can I do so that I don't have to reboot my first ASA everytime modem reboots.
View 6 Replies View RelatedLately I've been experiencing connection problems between my router and cable modem. Every night after 11:00 PM EST, my Internet connection sporadically goes out. I called my ISP who said there was nothing wrong on their end. Plugging directly into my modem allows me to access the Internet. When I wake up in the morning, the connection is back until 11 or later again. I ran WireShark but I'm not sure what to be looking for. There are a lot of random things from the LLMNR protocol like standard query A zmtvrjaql.
View 2 Replies View RelatedI use an adsl router DSL-320B to connect my Linux server (Fedora 12) to the web.I noticed in my logs that it was renewing its ip about every 30s.
View 1 Replies View RelatedRegion : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
So I just got hooked up to the internet via qwest the other day with my room mate. We have a wireless modem (PK5000) and he's using the AE2500 usb adapter to get online. Now, he can get online, but if he ever turns off or sleeps his computer, he can't connect when he turns it back on. His computer can see the network, full signal, but when he tries to connect it says cannot connect and under troubleshoot options suggests we should move his computer closer to the modem, but its only about 20 feet away and shows full signal. To get it to work, we need to go into the modem config and reset the wireless options. No changes are made, just scroll to the bottom and click apply, and presto change he can connect with no problems.He's running windows 7 home edition 64 bit. The modem's security is WPA/WPA2.
View 1 Replies View RelatedI have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
I've bought a "WAG160N v1.0 Annex A" almost 2 years ago. I never used it's wireless feature untill we moved our house. Now it's like 4 month I'm using its wifi feature and I've got to admit I'm really frustrated by its functionality!
For months the modem just dropped wireless connection constantly in various time periods. Somtimes it went like 2 days without any problem but some other times I had to change channel every 15 minutes for it to get back working. And yes it didn't get fix until I changed the channel, otherwise clients had to wait several hours for a 50/50 chance of reconnection. Now It's two days the changing channel trick no longer works. I tried all channels and even put my notebook next to the modem but no luck. The notebook sometimes connnects to the access point but disconnects after a few seconds. Somtimes it doesnt even detect the SSID of my WAG160N modem. Some friends suggested that the wireless hardware of my modem is broken and no longer works but I'm eager to know if it is broken why is it still broadcasting and sending signal.
I've tried everything from upgrading and downgrading firmware to turning on and off the modem several times and changes modem position. And even tried the G-only 20MHz mode.We are at a very crowdy place. Using inSSIDer I could pick about 15 other access points. Only few of them are using Wireless-N, most of them are using Wireless-G.This is the inSSIDer diagram of my WAG160N modem from a client: [code]
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View RelatedI want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
View 4 Replies View Relatedi just bought a Netgear WNDR4000 router due to troubles with my current modem/router combo (D-Link DSL2730-B). The router doesnt have in built modem functionality obviously so I need to set up the modem/router as a dedicated modem.Also should I use the current modem/router as the dedicated modem or an older model i own (I think its a DSL 502T)? Because the current one often drops the internet connection. Don't know if its a problem with the modem functionality or something else. Will the older one serve better since i didn't have any problems with that one or will it be outdated? I only upgraded due it not having wireless capabilities. Otherwise it's fine.Or will I be even better off buying a dedicated modem? I really don't want to spend more money but if this is a far better alternative I guess i will.
EDIT: Ok so found out that I have to put the modem/router in bridge mode in order for this to be possible. However, looking up how to do this lead me to a dead end because i need to fill in some fields that i have no idea how to interpret.
VPI:
VCI: These 2 already came with presets. Should I just leave them?
Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge): Choices of EoA PPPoA and IPoA
Encapsulation Mode: Choices of LLC/SNAP-BRIDGING and VC/MUX
Service Category: UBR without PCR, UBR with PCR, CBR, Non Realtime VBR, Realtime VBR
[code]...
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View Relatedmy computer randomly disconnects from my modem and will not reconnect until I restart my computer (do not need to restart modem). When I check the modem, it always is still running. The lights on the modem do the exact same thing whether the internet is working or not. The disconnection is entirely random. Sometimes it will disconnect immediately, sometimes it will take up to a few hours. I do not have a router hooked up to the modem, and the only other thing the modem is hooked up to is our tv. But even when the tv box is off, we still randomly disconnect.
On the previous forum thread that I read, some of the comments asked for the person to paste their entire ipconfig and their entire ping list from command prompt I will post that below: [code] Could it possibly be a virus? I am currently performing a virus scan using Microsoft Security Essentials. I will report the results of that tomorrow, seeing that it will take several (up to 10) hours to finish and it is nearly midnight of me posting this.I should also note that whenever I unplug my Ethernet cord it gives me a symbol that looks like this other than the regular disconnect with the red "X" over the wire symbol.
I'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
View 3 Replies View RelatedI have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View RelatedI use a DSL internet and i am assigned a new ip everytime my modem is restarted. I want to use the same ip everytime either through changing it or any other way. I mean can i use my own ip?
View 3 Replies View Relatedi have a at&t modem and wireless router in one. its the source of my internet and is in my office room and i was wondering if i can use my old westell wireless modem router and hook it up in my bedroom so i can have a better signal for my laptop and use an ethernet cable for other things like the tv and ect
View 1 Replies View RelatedI am running Wondows XP OS and have 2 NIC's in it. One is connected with DSL and other is with LAN of my Network. By using CCProxy 6.4.1 I am running the Internet on my LAN. I also want to run CCTV camera Sevice and want to share it on LAN as I share Internet on LAN but Camera Service Packets do not route on LAN but routhe when i disconnect the DSL Connection. So what i have to do to run both services (internet + camera service) smoothly.
View 1 Replies View RelatedI have two wireless adapters "PCI Marvell Libertas" and "USB Sagem" and i have access to 2 different AP's, The browsing' seem to be a little slow while i'm downloading', and my work requires lot's of downloading', as i have managed to connect to my two different AP's at the same time, i always feel like i'm usin' only one of 'em, so i was wondering' if i can take advantage of both connection in order to double the speed, and or if there's some way to use one for browsing' and the other for torrent downloads only.i've tried to mount the USB adapter on Linux using' Vmware, but it keeps saying' unable to get IP address,,However that's not the problem,, all i want to know is if there's a way to make both connection work on windows 7 Ultimate X64,
View 1 Replies View RelatedI have two wifi networks in my home, 1 has the internet wifi signal and 2 is my personal network. How can I use the internet signal from one whilst staying connected to my own network.the net sifi signal is from a virgin media superhub, and my personal wifi network is using an asus rt-n65u which has a wds mode not sure if this
View 9 Replies View Related
