I have a Cisco 857W router which I have aquired without cost. I want to use the wireless abilities of this router to be the wireless point to get into my home lab while I am studying for my CCNA and beyond.
I have erased it to its factory settings. There is no ADSL connection to it just yet, I might connect in to my internet connection another time. Not just yet.
I dont even know where to begin. I have searched all the internet and there is nothing really anything there to guide me to set it up from the very beginning.
I need developing a acl that can block a computer on the LAN from accessing the internet from midnight to 7am everyday. The router is a 857W, the computer is 192.168.2.33 the internal gw 192.168.2.254 (dialer 1 is 1.2.3.4).acl 101 deny tcp host 192.168.2.33 eq wwwwhat I need to figure out is how to add a time based acl to just this computer.
my trouble is I have a cisco 857w and I have never configured a wireless config for a cisco router before. Ok so i have had a go through the web interface (i know, last resort) and still no joy
Basically what im looking for is to have a visible (broadcast ssid) network with a password (WEP/WPA/WPA2, not picky) and it to be joined to the same vlan as the ethernet ports (VLAN 1).
I am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
Unable to see the logging message on the user context on ACE,but able to view the logging on the Admin Context.
Admin# sh logging Message logging: none Buffered logging: enabled (level - debugging) maximum size 1048576 Buffer info: current size - 1048576 global pool - 1048576 used pool - 1048576 min - 0 max - 1048576 cur ptr = 916918 wrapped - yes
I'm trying to configure an 857W to provide Internet connection via ADSL to LAN and WLAN clients on different networks, provided by DHCP. From the documentation, I see that the 857W supports 1 wired VLAN and 10 wireless VLAN. As the only VLAN which can be explicitly configured is VLAN1, which I want to manage the router, for the Wireless sections I have used VLAN11 and VLAN12.
I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
Looks like cisco 857w does not support pptp client in my IOS version, only l2tp is supported. Does there is some IOS version I can upgrade/downgrade to configure cisco as pptp client?
we have a model CISCO857W-G-E-K9 with IOS version 12.4(15)T17 We're trying to install Cisco Configuration Professional Express 2.7 and in particular the package cisco-config-pro-exp-admin-k9-2_7-en.zip following the install guide we found here
There's no way it works. After we've format the flash leaving inside only the System image file that is "flash:/c850-advsecurityk9-mz.124-15.T17.bin" and the tar image denominated ccpexpressAdmin27.tar every time we launch the command
it finish with an error about impossible to extract filenames longer than 45 characters. So it stopped to uncompress the .tar files and it doesn't work. I can't understand why this happens and it doesn't seems to have a solution.
My client has an 857w, but although the site for the SDM express loads, the Internet WAN page always shows as blank. We need access to this to alter the ISP.On IOS 12.4(6)T5
AI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
i have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
I have a 857w and a 857 router but there doesnt seem to be any HSRP and VLAn support on either router. I have ADVsevcurity on the routers do Ineed a different IOS or is it just not supported.
I need to replace an ADSL modem and have a spare 857W. Can I use this to act as a simple bridge between the ADSL PPPoA connection and the FW WAN port?
[ CISCO 857W ] ISP - PPPoA - BRIDGE - FW WAN
I have a block of Public IP's so the PPPoA Dialer 0 connection would get x.x.x.185/29 I would like to bridge this directly to the FW WAN port and set that to x.x.x.185/29 with a gateway of x.x.x.186/32.Currently I am using it in router mode with no NAT or FW and am losing a Public IP as I need to set the FW WAN as x.x.x.186 with a GW of x.x.x.185 I am setting BVI 1 as x.x.x.185/29 and Dialer0 as IP Unnumbered BVI 1.
I have a spare Cisco 857w that I am playing around with to learn.I managed to reset it to default, upgrade the ios to 12.4 However for the llife of me I cannot ping this device.
I have a 857w adsl router, I have configured it to connected to my ISP and i get a dhcp address from them, and I have dhcp pool to assign ip addresses to wireless or LAN, i have nat overload on a BVI . I am now trying to get one of the LAN port which has a device of 172.16.0.3 to be accessible from the outside world, but it will not let anyone connect to it.
Internet usage is very slow when initially opening a site from LAN clients. Once established it is OK. If I ping a site from an LAN client by either host name or IP address it takes about 5 seconds, drops the first packet then is fine after that. if I ping it again immediately afterwards it is fine. But if i wait 2 minutes and try again the problem returns. So I would conclude that seeing it is the same whether I use Host name or IP address it is not a DNS issue. Pinging from the router produces no fault at all. [code] I can ping the router internal and external interface or any internal ip or hostname from the LAN with no delay or hesitation so it is not a switch interface or network card problem.Some sort of NAT issue maybe? [Code]
I have an issue with a Cisco 857w. When I connect on via SDM I get a message saying "SDM has detected enabled debugs on the router. Because debugs degrade the performance of the router and of SDM, it is recommended that they be disabled". I've connected onto the router via telnet and ran the show debug command which indicates that dot11 debugging is on and when I run the command no debugging all it turns it off. I then do a copy run start and reboot the router and it comes back on. how I permanently disable it?
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2, Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory. DRAM configuration is 64 bits wide with parity disabled. 255K bytes of non-volatile configuration memory. 250880K bytes of ATA System CompactFlash 0 (Read/Write)
I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
At my office we have public wireless and our Domain based wired connection is locked down tight as a drum. On my Laptop, When I want to download something, I have to disable wired and enable wireless, once I'm done, I disable wireless and re-enable wired. Is there any other better way to do this?
I am using a desktop computer and have the router downstairs so I am using a wireless usb to connect to the internet. My router is a Linksys E1000 and the wireless adapter is a Netgear WG111v2. The problem is Every few mins I drop connection for may 5-30 secs and then the internet is fine. During that time it does not say I only have local connection or anything like that it constantly says I have internet connection even when I dont. It is very noticable when i am playing an online game on my computer. I will get a few mins in and then it will drop kicking me out of the game and by the time I get kicked out my Internet is reconnected and I can join again.
When I first got my DIR-655 (Hardware version B1) the Wireless would keep on turning itself off, and it needed a reboot of the unit to turn it back on again.After having upgraded to the 2.03NA version of the Firmware it seems to be working correctly and hasn't turned off for a few days now.
My kid is heading off to college with a Toshiba Satellite E-205 laptop and a Kodak ESP Office 2150 printer. She would like to use the wireless printer option on the Kodak, which requires a wireless router. I have a D-Link DIR-655 wireless router that I can send with her.
I know her university has a very robust wireless system for Internet access, so she is going to want to use their wireless access.
So, the DIR-655 sole use will be to allow access to the printer. It will not be accessing the Internet or be cabled into the university's network.
Is it possible to operate TWO wireless connections at the same time so she can hit her university wireless and the DIR-655 so she can print wirelessly?
how do I configure the laptop and the DIR-655 to allow this kind of access?
