I am trying to configure the wireless on my cisco 857W. The clients associates with router but they can't go on internet.
Building configuration...
Current configuration : 4123 bytes
!
! Last configuration change at 12:45:15 CET Sun Nov 18 2012 by simone
[Code].....
my trouble is I have a cisco 857w and I have never configured a wireless config for a cisco router before. Ok so i have had a go through the web interface (i know, last resort) and still no joy
Basically what im looking for is to have a visible (broadcast ssid) network with a password (WEP/WPA/WPA2, not picky) and it to be joined to the same vlan as the ethernet ports (VLAN 1).
I need to replace an ADSL modem and have a spare 857W. Can I use this to act as a simple bridge between the ADSL PPPoA connection and the FW WAN port?
[ CISCO 857W ]
ISP - PPPoA - BRIDGE - FW WAN
I have a block of Public IP's so the PPPoA Dialer 0 connection would get x.x.x.185/29 I would like to bridge this directly to the FW WAN port and set that to x.x.x.185/29 with a gateway of x.x.x.186/32.Currently I am using it in router mode with no NAT or FW and am losing a Public IP as I need to set the FW WAN as x.x.x.186 with a GW of x.x.x.185 I am setting BVI 1 as x.x.x.185/29 and Dialer0 as IP Unnumbered BVI 1.
I have a spare Cisco 857w that I am playing around with to learn.I managed to reset it to default, upgrade the ios to 12.4 However for the llife of me I cannot ping this device.
View 1 Replies View RelatedI have an issue with a Cisco 857w. When I connect on via SDM I get a message saying "SDM has detected enabled debugs on the router. Because debugs degrade the performance of the router and of SDM, it is recommended that they be disabled". I've connected onto the router via telnet and ran the show debug command which indicates that dot11 debugging is on and when I run the command no debugging all it turns it off. I then do a copy run start and reboot the router and it comes back on. how I permanently disable it?
View 1 Replies View RelatedMy client has an 857w, but although the site for the SDM express loads, the Internet WAN page always shows as blank. We need access to this to alter the ISP.On IOS 12.4(6)T5
View 7 Replies View RelatedI'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
Where can I find a list of supported external HDDs or NAS devices for a Cisco 857w router?
View 2 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
I have a Cisco 857W router which I have aquired without cost. I want to use the wireless abilities of this router to be the wireless point to get into my home lab while I am studying for my CCNA and beyond.
I have erased it to its factory settings. There is no ADSL connection to it just yet, I might connect in to my internet connection another time. Not just yet.
I dont even know where to begin. I have searched all the internet and there is nothing really anything there to guide me to set it up from the very beginning.
configuration for wireless on the cisco 887w? i would like wireless and wired users on the same vlan if possible i am trying to bring the radio up but it says reset and down and cant get it to bring it up ( i have done vlan1, ip unmbered vlan1 bit and logged onto ap using service-module wlan-ap0 session command) Also is wpa 2 enterprise possible on the cisco 887 w ( if possible i would like it to authenticate with our acs servers on our main site)
View 8 Replies View RelatedI need developing a acl that can block a computer on the LAN from accessing the internet from midnight to 7am everyday. The router is a 857W, the computer is 192.168.2.33 the internal gw 192.168.2.254 (dialer 1 is 1.2.3.4).acl 101 deny tcp host 192.168.2.33 eq wwwwhat I need to figure out is how to add a time based acl to just this computer.
View 2 Replies View RelatedI am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
Unable to see the logging message on the user context on ACE,but able to view the logging on the Admin Context.
Admin# sh logging
Message logging: none
Buffered logging: enabled (level - debugging) maximum size 1048576
Buffer info: current size - 1048576 global pool - 1048576 used pool - 1048576
min - 0 max - 1048576
cur ptr = 916918 wrapped - yes
[code]....
I'm trying to configure an 857W to provide Internet connection via ADSL to LAN and WLAN clients on different networks, provided by DHCP. From the documentation, I see that the 857W supports 1 wired VLAN and 10 wireless VLAN. As the only VLAN which can be explicitly configured is VLAN1, which I want to manage the router, for the Wireless sections I have used VLAN11 and VLAN12.
View 3 Replies View RelatedIn 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedI've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
Why does mine show this and NOT all 4 ports and 1 wan port?
Manases#sh verCisco Internetwork Operating System SoftwareIOS (tm) C831 Software (C831-K9O3SY6-M), Version 12.3(2)XA7 [code]...
How do I make it show all my ports? when I plug in something to port 1-4 it shows me on the log that I plug in to e0. I got port1-4 and 1 wan port.
I was recently given a PIX 501 router. I am very new to the world of Cisco, but want to learn. I got a few things setup on the router but, am not sure how to get it to use my DSL connection. My DSL modem IP is 192.168.2.1. Below is my router config. What more do I need to do? Also, is the outside IP not the IP of the DSL modem?
PIX Version 6.3(1)
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
[Code]...
i have the asa5505. the configuration of asa 5505 is:
: Saved
Code...
i analyzed this traffic i see problem with the nat- Asymmetric NAT rules matched for forward and reverse flows. where i made error?
how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?
View 1 Replies View Relatedi have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies View RelatedI have been using a Cisco 877 to connect to BT broadband and it was working fantastically with no issues. For reasons outwith my control we have moved to 02 and I cannot get the cisco router to connect (the supplied router works fine). O2 support is limited as they say they will not assist in the config of third party routers but they have supplied the below (the line has a static IP). I have also included my current config which was working fine with BT. I have attempted to write in the updated info but have been unable to get the line to connect. [code]
View 6 Replies View Relatedi have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
I have a network behind an 861 and users are unable to access e-mail from the local exchange server from their iPads using the 802.11wireless network. The wilrelss network is working fine and the iPad users connect fine.I was told that that i need to configure "hairpin DNS".
View 2 Replies View RelatedAny configuration example to build a vpc b/w 5ks and 7ks? i have total 4 links between them . If not, I am assuming to have the following config for the port-channels:- (Provided the vpc domain is configured).
N5k1 and 2:
int eth1/10-11
channel-group 10 mode active
switchport mode trunk
int po10
switchport mode trunk
switchport trunk allowed vlan a-d
[code]....
So, its basically vpc 10 that has 4 physical links b/w the vpc domain of 7ks and vpc domain of 5ks.
I'm currently trying to get up to speed on a 1941W ISR. I belive i have most of the configuration correct based on reading the documents on this site. However, i'm noticing that my lan to lan network performance is very slow. Peaking out about 3mbs. I was reading some documentation that suggested MGF (MultiGigabit Fabric) might resolve this problem.
I have a basic setup in my test environment trying to emulate a branch deployment. 1941W connected to a access switch (3400).
- I'm getting slow perfomance (thoughput) between the vlans 66,30,10. Will MGF fix this problem? How do i configure it?
Building configuration...
Current configuration : 7474 bytes
!
! Last configuration change at 09:26:04 PCTime Fri Dec 28 2012 by xxx
! NVRAM config last updated at 09:26:05 PCTime Fri Dec 28 2012 by xxx
[Code]......
We recently switched a faulty N5548UP with a replacement and everything went fine, with the exception of one minor thing.
We're currently unable to authenticate using tacacs+.
When trying to enter the command 'aaa authentication login default group [groupname]', the following msg appears: too big pss key or value size could not update aaa configuration
We're running 5.0(3)N2(2b).
I currently work in the IT field part-time as a end-user support technician while I am finishing my Bachelor's Degree in Network Administration. I'm not completely new to networking at this point, but I am by no means a master of it either. The basics of small networks (less than 10 PCs) and the lower-end of small business grade Cisco equipment are not unfamiliar to me. Up until this point however, I have had very little experience with any higher-end Cisco networking equipment.
Now on to the questions, which may seem like the answers should be obvious, but let's face it, I do not have the resources to own much equipment myself at this time for experimentation purposes, nor does the school I am attending have a lot of financial resources to provide us with recent hardware to learn on. What I want to know are a few things about PoE as implemented on Cisco devices, specifically the SG200-50P small business series switch. According to the technical documentation, the switch supports PoE on 24 of its 48 ports, specifically 1 - 12 and 24 - 36; simple enough. The switch is currently installed in an office that has less than 24 connected devices, but that is currently expanding. None of the PoE ports are utilized as of yet, but going forward, there will be more than 24 connected devices. Will another switch need to be installed if the additional connected devices (PCs and printers) are not using PoE, or is the PoE an auto-sensing feature that will simply remain disabled if a device that does not require power over the network cable is connected? Is there some setting that needs to be changed through the management interface to keep devices that should not be drawing power from doing so?
There will likely be some additional questions generated by my inquiry, and I fully understand if these are completely novice questions, but I admittedly do not know the answer. When I Googled it, I was greeted by a few hundred thousand results, the first dozen or so pages of results all being for places to purchase this particular type of switch, so I thought I would try my luck on the forums of the place that made it.
On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
I am trying to configure a 891 W to basically provide DNS from my ISP to my internal clients on the 891 W. Currently when I am on a PC I can see that I receive my IP information along with the correct ISP DNS IPs. However when I try to connect or resolve a URL it fails. Nor can I perform an ns lookup from the cli of the 891 W. I seem to be having a translation issue with DNS.
View 2 Replies View RelatedLooks like cisco 857w does not support pptp client in my IOS version, only l2tp is supported. Does there is some IOS version I can upgrade/downgrade to configure cisco as pptp client?
View 1 Replies View Relatedwe have a model CISCO857W-G-E-K9 with IOS version 12.4(15)T17 We're trying to install Cisco Configuration Professional Express 2.7 and in particular the package cisco-config-pro-exp-admin-k9-2_7-en.zip following the
install guide we found here
There's no way it works. After we've format the flash leaving inside only the System image file that is "flash:/c850-advsecurityk9-mz.124-15.T17.bin"
and the tar image denominated ccpexpressAdmin27.tar every time we launch the command
it finish with an error about impossible to extract filenames longer than 45 characters. So it stopped to uncompress the .tar files and it doesn't work.
I can't understand why this happens and it doesn't seems to have a solution.