my trouble is I have a cisco 857w and I have never configured a wireless config for a cisco router before. Ok so i have had a go through the web interface (i know, last resort) and still no joy
Basically what im looking for is to have a visible (broadcast ssid) network with a password (WEP/WPA/WPA2, not picky) and it to be joined to the same vlan as the ethernet ports (VLAN 1).
I am trying to configure the wireless on my cisco 857W. The clients associates with router but they can't go on internet.
Building configuration...
Current configuration : 4123 bytes
!
! Last configuration change at 12:45:15 CET Sun Nov 18 2012 by simone
[Code].....
I have an issue with a Cisco 857w. When I connect on via SDM I get a message saying "SDM has detected enabled debugs on the router. Because debugs degrade the performance of the router and of SDM, it is recommended that they be disabled". I've connected onto the router via telnet and ran the show debug command which indicates that dot11 debugging is on and when I run the command no debugging all it turns it off. I then do a copy run start and reboot the router and it comes back on. how I permanently disable it?
View 1 Replies View RelatedI'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
Where can I find a list of supported external HDDs or NAS devices for a Cisco 857w router?
View 2 Replies View RelatedI need to replace an ADSL modem and have a spare 857W. Can I use this to act as a simple bridge between the ADSL PPPoA connection and the FW WAN port?
[ CISCO 857W ]
ISP - PPPoA - BRIDGE - FW WAN
I have a block of Public IP's so the PPPoA Dialer 0 connection would get x.x.x.185/29 I would like to bridge this directly to the FW WAN port and set that to x.x.x.185/29 with a gateway of x.x.x.186/32.Currently I am using it in router mode with no NAT or FW and am losing a Public IP as I need to set the FW WAN as x.x.x.186 with a GW of x.x.x.185 I am setting BVI 1 as x.x.x.185/29 and Dialer0 as IP Unnumbered BVI 1.
I have a spare Cisco 857w that I am playing around with to learn.I managed to reset it to default, upgrade the ios to 12.4 However for the llife of me I cannot ping this device.
View 1 Replies View RelatedMy client has an 857w, but although the site for the SDM express loads, the Internet WAN page always shows as blank. We need access to this to alter the ISP.On IOS 12.4(6)T5
View 7 Replies View RelatedI am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
we have a model CISCO857W-G-E-K9 with IOS version 12.4(15)T17 We're trying to install Cisco Configuration Professional Express 2.7 and in particular the package cisco-config-pro-exp-admin-k9-2_7-en.zip following the
install guide we found here
There's no way it works. After we've format the flash leaving inside only the System image file that is "flash:/c850-advsecurityk9-mz.124-15.T17.bin"
and the tar image denominated ccpexpressAdmin27.tar every time we launch the command
it finish with an error about impossible to extract filenames longer than 45 characters. So it stopped to uncompress the .tar files and it doesn't work.
I can't understand why this happens and it doesn't seems to have a solution.
about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies View RelatedI have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4
Here is VPN related config part and log from router and client.
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.
i have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.
View 2 Replies View RelatedI have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies View RelatedI have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
i have to configure 80 Cisco 876 routers, so i planned to copy config via tftp from one configured router to PC, edit it in text editor (change ip addresses, dhcp pools, vpn keys...) and then copy it via tftp to another router, etc... Configuration looks fine and it works when i paste it in cli, but when i copy it via tftp i'm getting strange problems like dhcp not working or snmp not accessible. Am I missing something.
Here's config from router with dhcp problem:
ROUTER#sh run
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers(code)
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
I have a 857w adsl router, I have configured it to connected to my ISP and i get a dhcp address from them, and I have dhcp pool to assign ip addresses to wireless or LAN, i have nat overload on a BVI . I am now trying to get one of the LAN port which has a device of 172.16.0.3 to be accessible from the outside world, but it will not let anyone connect to it.
View 9 Replies View RelatedI have not been able to figure out the resolution. The basic premise is to have 3 inside vlan networks controlled by a 1900 series router. Then have that primary LAN router connect to the inside of my ASA5505 Basic, then go out to my ISP Gateway. I have tried hundreds of different static route configurations on my router and asa. I have tried equally as many NAT and PAT configurations, but nothing seems to work. I have even tried using all the commands (specific to my topography of course) on this weblink from cisco: url...
View 12 Replies View Relatedi am currently using 2 DSL WIFI modem and wants to combine them to my RV042 dual wan router but as i set them up using WAN1 and Wan2 as "Obtain IP Automatically" there is no internet connection?
View 2 Replies View RelatedI have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedI've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
I have a Cisco 857W router which I have aquired without cost. I want to use the wireless abilities of this router to be the wireless point to get into my home lab while I am studying for my CCNA and beyond.
I have erased it to its factory settings. There is no ADSL connection to it just yet, I might connect in to my internet connection another time. Not just yet.
I dont even know where to begin. I have searched all the internet and there is nothing really anything there to guide me to set it up from the very beginning.
configuration for wireless on the cisco 887w? i would like wireless and wired users on the same vlan if possible i am trying to bring the radio up but it says reset and down and cant get it to bring it up ( i have done vlan1, ip unmbered vlan1 bit and logged onto ap using service-module wlan-ap0 session command) Also is wpa 2 enterprise possible on the cisco 887 w ( if possible i would like it to authenticate with our acs servers on our main site)
View 8 Replies View RelatedI need developing a acl that can block a computer on the LAN from accessing the internet from midnight to 7am everyday. The router is a 857W, the computer is 192.168.2.33 the internal gw 192.168.2.254 (dialer 1 is 1.2.3.4).acl 101 deny tcp host 192.168.2.33 eq wwwwhat I need to figure out is how to add a time based acl to just this computer.
View 2 Replies View RelatedUnable to see the logging message on the user context on ACE,but able to view the logging on the Admin Context.
Admin# sh logging
Message logging: none
Buffered logging: enabled (level - debugging) maximum size 1048576
Buffer info: current size - 1048576 global pool - 1048576 used pool - 1048576
min - 0 max - 1048576
cur ptr = 916918 wrapped - yes
[code]....