Cisco WAN :: Can Use Vwic2-1mft-g703 For ISDN PRI
Dec 4, 2011Can I use module vwic2-1mft-g703 for ISDN PRI?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: VWIC2-1MFT-G703 In 2921 Router
Jun 5, 2012I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies View RelatedCisco WAN :: ATM IMA Support On VWIC2-2MFT-G703
Sep 22, 2011I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies View RelatedCisco WAN :: VWIC2-1MFT-T1/E1 Not Recognized In C2600
Jul 4, 2011I am trying to install VWIC2-1MFT-T1/E1 into c2600 router w IOS C2600 Software (C2600-I-M), Version 12.3(26) with 28672K/4096K bytes of memory It is not recognized? Do I need another version of IOS?
View 2 Replies View RelatedCisco WAN :: Configuring IP Address On A VWIC2-1MFT-T1?
Mar 19, 2012I have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1 controller but still no luck.
View 1 Replies View RelatedCisco WAN :: 1941 Routers With VWIC2 1MFT-T1 On T1
Jul 11, 2011Trying to connect two Cisco 1941 routers with VWIC2 1MFT-T1 interfaces on point-to-point T1 (No Voice). Sample configuration, this is what I have so far, but I'm not sure if it's correct. Do I need any specific information from my point to point T1 provider?
ROUTER A
controller T1 0/0/0
cablelength long 0db
[Code].....
Cisco WAN :: How Maximum Channel-group Supported By VWIC2 1MFT G.703
Jun 14, 2012How maximum channel-group supported by VWIC2 1MFT G.703? And the CISCO1941/K9 ?
View 0 Replies View RelatedCisco WAN :: VWIC2-1MFT-T1 / E1 Card Support On 1841 Router?
Jun 13, 2011VWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies View RelatedCisco Switching/Routing :: Q931 / ISDN BRI Branch Connecting To ISDN E1 At Central Site?
Jun 6, 2012I have senario where 15 branches via bri connection to central ISDN E1 Pri Head office.The setup is working before and suddenly branches not able to dial head office.Below is the debug q931 logs from branch router and i am getting continous "channel not avalible message on Head office
Branch router logs
*********************************************************************************************
hmc#isdn test call interface bri 0/0/0 44492999
hmc#
007049: Jun 6 14:41:39.497 gmt: ISDN BR0/0/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
007050: Jun 6 14:41:39.721 gmt: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0/0, TEI 78 changed to up
007051: Jun 6 14:41:39.721 gmt: ISDN BR0/0/0 Q931: Sending SETUP callref = 0x002E callID = 0x84BC switch = basic-net3 interface = User
007052: Jun 6 14:41:39.721 gmt: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x2E
[code].....
Cisco WAN :: G703 - Signaling To Regular RJ45
Aug 29, 2011We have a customer in a country where the local telecom hands out the data E1 link in a G703 interface with two coaxial cables (Tx & Rx) out of a Watson/Schmidt Telecom SHDSL modem.
We need a way to convert the G703 cables and signaling to a regular RJ45 so that we can connect it to the customer firewall which has regular gigabit Ethernet connections. Some have suggested a 1941 with a serial and gigabit cards. We just need a affordable solution for this and the configuration.
Cisco WAN :: C2901 VWIC3-1MFT-T1 / E1 Frame Relay?
Dec 18, 2011IOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
Cisco WAN :: VWIC2 On Two Different T1 Circuits
Jul 29, 2011I have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies View RelatedCisco WAN :: Configuring Two T-1s On VWIC2-2MFT-T1/E1
Aug 7, 2011I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
Cisco WAN :: 2921 - VWIC2 Not Being Recognized?
Apr 3, 2012I have a 2921 router, with UCK9 services on it. I've installed a VWIC2-2MFT but the system is not seeing it. I've been told there is a command required to enable the card, is this true? I've always done most of my UC work on the 2800 range and never had to run an enable command, it just saw the card.
View 5 Replies View RelatedCisco WAN :: To Use VWIC2 2MFT T1 Along With NM HDV2 2T1 On 2921
Oct 10, 2012Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies View RelatedCisco WAN :: VWIC2-2MFT-T1/E1 - PPP Multilink Configuration
Jun 15, 2011I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
Cisco WAN :: VWIC2-2MFT-T1/E1 Work With 2951?
Jul 19, 2012I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
Cisco WAN :: VWIC2-2MFT-T1/E1 - Does IOS Supports Unframed G.703
Mar 8, 2011i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies View RelatedCisco :: Running ISDN On PRI With BRI?
Jan 21, 2013connecting PRI to BRI interface on ISDN. I have all this information provided by the TELCO and i have configured it but due to some reason i am not able to connect them. I have given the questions with answers provided by the TELCO. I am also providing the running configuration of the PRI interface and also the error message i am getting when trying to test call itself.
1. Is the PBX designed for Pre-National or NI-2 protocol? -
Protocol using C7MATL
2. Are there any DID station numbers that your CPE cannot accept? -
No
(i.e. 0 or 9 in the 4th position)
3. Which carriers will be your choices for your PIC and LPIC? -
Carrier using DChannel
[code]....
Cisco WAN :: Configuration Of 2x ISR 886 In ISDN
Aug 28, 2012I'm trying to configure 2 routers (cisco 886) to create a link between them via ISDN link (in france) but it doesn't work
I think I put a base conf but nothing work :
LAN 1 (192.168.220.0/24) => BRI0 (172.23.240.1) Cisco 886 <= ISDN => BRI0 (172.23.240.2) Cisco 886 => LAN 2 (192.168.255.0/24)
both conf are about the same (not IP and phone number) :
...
interface BRI0
ip address 172.23.240.1 255.255.255.0
encapsulation ppp
dialer idle-timeout 600
dialer string xxxxxxxxxxxxx
dialer-group 1
isdn switch-type vn3 (code)
Cisco WAN :: Install VWIC2 Card Into 3825 Router
May 29, 2011We have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
Cisco WAN :: VWIC2-2MFT-T1/E1 Hardware Installation Guide
Aug 10, 2011the VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies View RelatedCisco WAN :: 2800 - ISDN PRI And BRI Configuration
Jun 4, 2011I have a Cisco 2800 series router with E1 PRI module at Head Office,and Cisco 786 with single ISDN BRI port,When I dial from either side only one B channel is up ,means 64 K only.
View 1 Replies View RelatedCisco WAN :: 1571 - ISDN BRI And Ethernet
Aug 5, 2012I have a problem with ISDN BRI-1B-S/T-V3. In the documentation I read: "The ability to add BRI connectivity via a WLC lets administrators maximize valuable slot space while it provides additional connectivity options, such as Ethernet, on the same module." Does it mean that I can plug in the module Ethernet and it will work? I ask, because i have CISCO 1571-V router with this isdn module, i get the internet from Ethernet, and i wonder is there any possibility to use this module as WAN.
View 1 Replies View RelatedGet A ISDN Modem With At Least 4 Channels?
Aug 12, 2011Where you get get a modern ISDN modem with at least 4 channels? I am 2 miles from Cable and .5 miles from dsl.ISDN is the only option cause I play games online. Would 256K or 128K Up and Down be enough for playing FPS games on xbox live? I cant find any ISDN modems that are new. Only used ones on ebay that I dont know would work on windows 7.
View 1 Replies View RelatedCisco WAN :: Does VWIC2-2MFT-T1/E1 Card Work With 2911 Router
May 5, 2011I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies View RelatedCisco :: Outbound Calling To Two ISDN BRI Ports?
Oct 21, 2011Both of these ISDNs are up, this gives us 4 channels. Someone said they recieved a busy tone when they attempted to dial out. I looked over the system and seen there are two outbound pots dial-peers. Each dial-peer references one of the BRI ports. The preferences are the same on each dial-peer. I think what is happening is that the system is randomly selecting one of the dial-peers due to the preference, even if both channels of the BRI are in use. How does the system know if that port has both channels in use? I've not used ISDN before, so tried to enter the B-channel sub interface and the system (UC500) tells me I cannot do this. I was thinking about adding each channel into a trunk group and then referencing the trunk group in the dial-peer. I can obviously add both BRI's into one trunk group.
View 2 Replies View RelatedCisco WAN :: 7206VXR - Maximum Possible ISDN Calls?
Jun 12, 2011What is the maximum possible ISDN calls on Cisco 7206VXR router using PRI links and PRI supported cards.
View 7 Replies View RelatedCisco WAN :: Cannot Dial Out From ISDN Line With 1812j
Jan 11, 2011Now I am tring to setup Cisco 1812j with ISDN Line.
Here is what I connect the device. (I am in Japan)
ISDN Line (NTT east) >> DSU(NTT east INS Mate V30Slim with S/T port) >> Cisco 1812j(S/T)
On DSU setting I enable DSU and Disable Terminator.
First of I would like to test outbound call. Here is the config.
interface BRI0 ip address 192.168.92.2 255.255.255.0 encapsulation ppp dialer map ip 192.168.92.1 name Router1 broadcast 080********(Cell Phone Number) dialer-group 1 isdn switch-type ntt isdn point-to-point-setup ppp authentication chap ppp chap password 0 CISCO ip route 10.92.0.128 255.255.255.248 BRI0 192.168.92.1
Then I test by ping with #debug dialer. #ping 10.92.0.129
And I could not receive a call by my cell phone landline either.
Here is the debug.
[Code]....
Cisco AAA/Identity/Nac :: ISDN Authorization With RADIUS Using ISE 1.1.2?
Nov 19, 2012I am trying to move my ISDN dialup branches authentication/authorization from old ACS 4.1 to ISE appliance. Before it was through ACS 4.2 with TACACS protocol but now since we are moving to ISE we are moving them to ISE with radius.
Problem is that isdn client gets authenticated and authorized but calls get dropped and they dont able to communicate with HO. IP address is assigned by Head End router to all remote isdn dialing branches..
I have used default "PermitAccess" in authorization policy and authentication policy is also default. I dont understand where I am going wrong as authentication and authorization is sucessful.
aaa authentication ppp default group radius local
aaa authentication network default group radius
aaa accounting network default start-stop group radius
radius-server host 12.18.22.41
radius-server key *****
Cisco WAN :: 886VA - VDSL Over ISDN With PPPoE
Aug 8, 2011I will install in the next days a 886VA router (VDSL over ISDN using PPoE). Since I have no possibility to verify the VDSL config, this is what i prepared. Is this config OK (only VDSL part) ?
controller vdsl 0
operating mode auto
interface Ethernet0
[ code]...
For VDSL over ISDN the interface Ethernet0 must be used instead of ATM . Is this config correct ?
Cisco WAN :: VWIC3-1MFT-T1 / E1 / Point To Point Serial Link Configuration?
Jan 12, 2011How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies View RelatedConnecting Pstn (modem) To ISDN (TA)?
Feb 21, 2011our client are using PSTN (modem) and is dialing up to our ftp box which is using ISDN (TA). according to them, they not facing any problem to dial up to other vendor which is using the same network infra (PSTN to ISDN). but, unfortunately in wont happen in my case which they (client) keep receiving the busy tone when they dialing to our ISDN no. i've set in our TA to accept both digital and analog calls and i'm using the DSS1 protocol which been told by our line provider.
View 2 Replies View Related