Cisco WAN :: 2921 - VWIC2 Not Being Recognized?
Apr 3, 2012
I have a 2921 router, with UCK9 services on it. I've installed a VWIC2-2MFT but the system is not seeing it. I've been told there is a command required to enable the card, is this true? I've always done most of my UC work on the 2800 range and never had to run an enable command, it just saw the card.
View 5 Replies
ADVERTISEMENT
Jul 4, 2011
I am trying to install VWIC2-1MFT-T1/E1 into c2600 router w IOS C2600 Software (C2600-I-M), Version 12.3(26) with 28672K/4096K bytes of memory It is not recognized? Do I need another version of IOS?
View 2 Replies
View Related
Oct 10, 2012
Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies
View Related
Jun 5, 2012
I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies
View Related
Jul 29, 2011
I have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies
View Related
Aug 7, 2011
I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
View 4 Replies
View Related
Dec 4, 2011
Can I use module vwic2-1mft-g703 for ISDN PRI?
View 1 Replies
View Related
Jun 15, 2011
I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
View 1 Replies
View Related
Jul 19, 2012
I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
View 6 Replies
View Related
Mar 19, 2012
I have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1 controller but still no luck.
View 1 Replies
View Related
Sep 22, 2011
I have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies
View Related
Jul 11, 2011
Trying to connect two Cisco 1941 routers with VWIC2 1MFT-T1 interfaces on point-to-point T1 (No Voice). Sample configuration, this is what I have so far, but I'm not sure if it's correct. Do I need any specific information from my point to point T1 provider?
ROUTER A
controller T1 0/0/0
cablelength long 0db
[Code].....
View 1 Replies
View Related
Mar 8, 2011
i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies
View Related
May 29, 2011
We have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
View 10 Replies
View Related
Aug 10, 2011
the VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies
View Related
Jun 14, 2012
How maximum channel-group supported by VWIC2 1MFT G.703? And the CISCO1941/K9 ?
View 0 Replies
View Related
May 5, 2011
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies
View Related
Jun 13, 2011
VWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies
View Related
May 10, 2013
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
View 1 Replies
View Related
Feb 17, 2013
The onboard NIC on my Asrock Extreme6 Z77 has stopped working. I had recently moved my system in to a newer and better home, and after moving it in to the new case the NIC stopped working. I had originally thought that I may have zapped it, but looking at the device manager I saw that it was enabled and recognized by Windows. So I tried some trouble shooting.
- Uninstall and re-install drivers.
- Different cables (5 in total, 3 of which work on other machines)
- Disable and re-enable.
- Went out and bought a wireless USB, allowed me to connect to the internet this way.Then yesterday it started to work again after not using the computer for most of the day.Could play some Battlefield 3, and about 2 hours in to gameplay it stopped working.Ran trouble shoot on Windows, something quickly popped up saying something about ip wasn't reconfigured/updated/some BS like that.Finished for the night happy it was working again and then came back on tonight and now it's not working again.
- Updated BIOS.
- Deleted McAfee
- Verified it was turned on in UEFI (doesn't show connected in system browser in UEFI)
Windows IP Configuration
Host Name . . . . . . . . . . . . : Crosby-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]...
View 4 Replies
View Related
Oct 26, 2011
I just installed a fresh copy of Windows XP Pro SP3 on one computer. Now my other PC has Windows7. I connected the two with a LAN cable, and in 'Network' the Windows 7 PC picks up the shared folder of the XP PC automatically, but the XP PC does not show the Windows 7 Shared(Public) folder. Can it be the Antivirus? XP PC has MS Security Essentials and Windows 7 PC has ESET.
View 1 Replies
View Related
Jul 4, 2011
I'm running on LMS 3.2 and RME 4.3.0 and one type of device was not recognized.this is NME-X-23ES-1G (IOS : 12.2(35)SE5) in a 3825 url... this module is supported with the OID 1.3.6.1.4.1.9.1.703,but in the device center I've found something which seems to be the right equipement :
- Cisco Interfaces and modules
- Cisco Network Modules
- Cisco 2800,3800 series 23-port EtherSwith Service module with OID 1.3.6.1.4.1.9.1.664
View 1 Replies
View Related
Jun 10, 2013
I have Prime 4.1 on windows with the latest update, it is up and running except for few devices ASR903 routers that are not being recognized in the Fault (DFM). These devices are supported in this release, The fault is showing that the devices are stuck at 10% learning state. The strange issue is that when i click on the routers that are in the learning state some shows in the device type as N/A ans others are showing "routers". Anyway i followed the steps mentioned in "How can I troubleshoot device discovery stuck at 10%"
View 1 Replies
View Related
Jan 24, 2012
I noticed in RME inventory, my ASR1001 hardware is not recognized. I checked my Ciscoworks and it only knows ASR1002, 1004, and 1006 routers.
I checked the supported device table for LMS 3.2 and did not find ASR1001. Is there a separate device package I can download. This is not a deal breaker, but it's unnerving to see the question mark icon next to the name of my router in the Cisco works GUI.
View 1 Replies
View Related
Jan 4, 2012
We have CAM/CAS 4.8.2, NAC agent 4.8.2.3 and compliance module 3.4.27.1. AVG 2012 cannot be recognized by NAC agent. From the link below, it should work: [URL].
View 1 Replies
View Related
Sep 20, 2012
Yesterday I was on my computer when all of the sudden my internet stopped working. I am using windows 7 and at the bottom right I see a big "X" over the small computer icon. I already tried a computer reboot, a router+modem reboot, system restore, and I even reset the power to the room of the modem+router from the fuse box in my house. I tried everything.
I'm sure the problem must be from the actual cable or mother board itself. ( I hope it isn't ) I tried blowing out any dust from the ports and making sure that nothing was blocking the connection. I fell asleep last night with the internet not working, and woke up to it working. Every other computer in my house works except for mine. I tried all of the router ports as well. I did not attempt another ethernet cable though because my room is far and I would need to make a very long one.
View 14 Replies
View Related
Mar 20, 2011
I have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband. A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.it works with a Zoom router, but not the Netgear.
View 3 Replies
View Related
Apr 25, 2013
An older post on this forum told me to remove the adapter's driver software and restart the system. I did this, and it tried to install the software on startup but it keeps failing when installing. Forcing it to look for new driver software resulted in it saying the best software is already installed.
View 4 Replies
View Related
Apr 9, 2012
We had a little family get together at my house which involved 2 smart phones and an iphone-(people were browsing using our unsecured router) and now the wireless router is not recognized by our pc's; it's like the wireless address just disappeared.
View 1 Replies
View Related
Oct 23, 2011
I have four 2811 routers with IOS 12.4(15)T installed. Embedded Event Manager was introduced in IOS 12.3(4)T, why do I not have it?! I've been at this for over a month, when I try to see the command 'event manager' I get Unrecognized command? According to all EEM documentation I can find, this should work on our machines!
View 4 Replies
View Related
Oct 2, 2011
We just replaced a floor swithc, and ended up going with an IOS-XE software, LMS does not seem to like this software, the device is not available in my Identity dashboard, it's abviously running dot1x.
LMS shows it as software version 03.02.01.SG, same as you get when you do a show version, license level is enterprise services.
Actual Image name: cat4500e-universalk9.SPA.03.02.01.SG.150-2.SG1.bin
Also, the IOS upgrade option does not work for this device, it give an error saying to perform an inventory collection, which I have manually performed, the device is reachable and manageable by LMS, and it does not show up in any of the IOS version reports.
View 1 Replies
View Related
May 7, 2013
After connecting ZTE636 USB modem to Cisco RV215W the modem is not recognized, even though it is on the compatible modems list. The stick is from Orange PL. Firmware upgraded to 1.1.0.5.
View 1 Replies
View Related
Aug 3, 2011
I just got this av to cat5 converter [URL]? and was thinking i could use a router on each end so it could be wireless. But the way they work the router does not see the converter when it is plugged in.
View 9 Replies
View Related