I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies
Can I use module vwic2-1mft-g703 for ISDN PRI?
View 1 Replies View RelatedVWIC2-1MFT-T1/E1 card support on 1841 Router ?any ios up-gradation required?
View 1 Replies View RelatedI have been advised by my service provider that to do ATM IMA I need an AIM-ATM and a VWIC2-2MFT-T1/E1 card, and that IMA is not support on the VWCI2-2MFT-G703 card.
View 5 Replies View RelatedI am trying to install VWIC2-1MFT-T1/E1 into c2600 router w IOS C2600 Software (C2600-I-M), Version 12.3(26) with 28672K/4096K bytes of memory It is not recognized? Do I need another version of IOS?
View 2 Replies View RelatedI have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1 controller but still no luck.
View 1 Replies View RelatedTrying to connect two Cisco 1941 routers with VWIC2 1MFT-T1 interfaces on point-to-point T1 (No Voice). Sample configuration, this is what I have so far, but I'm not sure if it's correct. Do I need any specific information from my point to point T1 provider?
ROUTER A
controller T1 0/0/0
cablelength long 0db
[Code].....
How maximum channel-group supported by VWIC2 1MFT G.703? And the CISCO1941/K9 ?
View 0 Replies View RelatedI have a 2921 router, with UCK9 services on it. I've installed a VWIC2-2MFT but the system is not seeing it. I've been told there is a command required to enable the card, is this true? I've always done most of my UC work on the 2800 range and never had to run an enable command, it just saw the card.
View 5 Replies View RelatedCan I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 1 Replies View RelatedWe have a customer in a country where the local telecom hands out the data E1 link in a G703 interface with two coaxial cables (Tx & Rx) out of a Watson/Schmidt Telecom SHDSL modem.
We need a way to convert the G703 cables and signaling to a regular RJ45 so that we can connect it to the customer firewall which has regular gigabit Ethernet connections. Some have suggested a 1941 with a serial and gigabit cards. We just need a affordable solution for this and the configuration.
We have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies View RelatedIOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
I have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies View RelatedI'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
(code)
I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.
[URL]
i have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies View Relatedthe VWIC2-2MFT-T1/E1 hardware installation guide?
View 1 Replies View RelatedHow do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies View RelatedI need a router to connect to our ISP by BGP and in a future to a second ISP. Our ISP is going to provide us about 300.000 route entries by BGP. So router 2921 would be enough??? or should i go to a higher model?We are going to have 100Mbps with this ISP and probably in 3 months we'll have to double it. Also we'll need IPv6 support.I saw router performance [URL]f and it's has 480.000 PPS and 245 Mbps but for 64 bytes lenght packages. If the packets are bigger the throughput should be best I suppose... 1500 bytes about 5,5 Gbps. In the case you consider the model is sufficient, the flash or RAM should be increased?
View 4 Replies View RelatedIs there a recommended number of GRE tunnels that Cisco 2921 ISR router with default configuration (512MB DDR2 ECC DRAM) can support?
View 5 Replies View RelatedI am installing a security license on Cisco 2911 Router for the first time. It already has a temporary license installed on it which is expiring soon. Cisco has already mailed me the procedure for installation. I want to know if i need to uninstall the previous license before installing the new one.
View 2 Replies View RelatedWe recently acquire a cisco 2921/K9 router to interface 2 networks
Network 1 : 169.254.XXX.XXX/16 on GigabitEthernet0/0 interface
Network 2 : 192.168.1.XXX/24 on GigabitEthernet0/1 interface
On the network 1 side there is a multicast source (169.254.200.200 destination : 225.0.0.1) on the network 2 side there is 1 receiver which is not multicast capable(old) but i want it to receive the multicast stream for the moment we configure the ip multicast-routing and each interface each interface with ip pim sparse-dense-mode then configure the GigabitEthernet0/1 in order to join the multicast group (using ip igmp static-group 225.0.0.1) and wireshark confirm that the multicast stream on the network 2 side from 169.254.200.200 -> 225.0.0.1 of course the receiver don't the stream, but if i force a "multicast to unicast" process inside the router it shall be ok.. after many hour of internet browsing i found 2 solution :
- NAT, [URL]
- multicast service reflection (Cisco documentation)
The NAT example don't work ,what is the best way to do this task.
I need to configure cisco router 2921 for snmp v3,
View 5 Replies View RelatedI just purchased thie Cisco 2921 router and have all the configuration completed except the Firewall and NAT. We have 4 supnets at our location on the router each with a DHCP handed from the router to our network. Any examples for the Firewall and Nat configurations?
View 6 Replies View RelatedWe have a 2300 RPS with single 1150WAC power supply (C3K-PWR-1150WAC) which is connected to one 2921 Router. But it is not backing the rotuer.
Router 2921 running IOS
c2900-universalk9-mz.SPA.152-2.T1.bin
I am getting the following logs:
*** External Redundant Power Supply is present, but type is unknown or not supported.***
%ENVMON-1-POWER_WARNING: : RPS Online Insertion and Removal is not supported.
Do we required any configuration to be done on Router end.
Note: The RPS is backing 2960 Switch.
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
I have a Cisco 2921 Router,with 3 giga interfacesi have a leased line for the internet with a public ip address and i want to configure this router as NAT /PAT gateway, so that users in my network can ue the internet by the router,my wan interface is g0/0 - ip 122.xx.xx.xx lan is g 0/1 -- 192.168.1.1 /24 . i have tried doing nat once but i was not able to make the wan port up.using cisco CP when i test the interface it givves error and i dont get internet to my users.
View 10 Replies View RelatedI have a trouble with PPTP VPN between Windows clients and Cisco 2921 router with RADIUS (IAS) authorization. When I try to connect to Cisco 2921 from Windows 7 using MS-CHAP v2 I receive error 778: it was not possible to verify the identity of server . Then I use PAP - everythig is OK. On Windows XP the same situation.
Cisco config:
version 15.0
service timestamps debug datetime msec
[Code].....
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View Related
